High Peformance and Low Power On-Die Interconnect Fabrics.

Increasing power density with technology scaling has caused stagnation in operating frequency of modern day microprocessors. This has led designers to prefer multicore architectures over complex monolithic processors to keep up with the demand for rising computing throughput. Although processing units are getting smaller and simpler, the dramatic rise of their count on a single die has made the fabric that connects these processing units increasingly complex. These interconnect fabrics have become a bottleneck in improving overall system effciency. As a result, the design paradigm for multi-core chips is gradually shifting from a core-centric architecture towards an interconnect-centric architecture, where system efficiency is limited by the fabric rather than the processing ability of any individual core. This dissertation introduces three novel and synergistic circuit techniques to improve scalability of switch fabrics to make on-die integration of hundreds to thousands of cores feasible. 1) A matrix topology is proposed for designing a fully connected switch fabric that re-uses output buses for programming, and stores shue congurations at cross points. This significantly reduces routing congestion, lowers area/power, and improves per- formance. Silicon measurements demonstrate 47% energy savings in a 64-lane SIMD processor fabricated in 65nm CMOS over a conventional implementation. 2) A novel approach to handle high radix arbitration along with data routing is proposed. It optimally uses existing cross-bar interconnect resources without requiring any additional overhead. Bandwidth exceeding 2Tb/s is recorded in a test prototype fabricated in 65nm. 3) Building on the later, a new circuit topology to manage and update priority adaptively within the switch fabric without incurring additional delay or area is then proposed. Several assist circuit techniques, such as a thyristor based sense amplifier and self regenerating bi-directional repeaters are proposed for high speed energy efficient signaling to and from the switch fabric to improve overall routing efficiency. Using these techniques a 64 x 64 switch fabric with 128b data bus fabricated in 45nm achieves a throughput of 4.5Tb/s at single cycle latency while operating at 559MHz.Ph.D.Electrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/91506/1/sudhirks_1.pd

A survey of fault-tolerance algorithms for reconfigurable nano-crossbar arrays

ACM Comput. Surv. Volume 50, issue 6 (November 2017)Nano-crossbar arrays have emerged as a promising and viable technology to improve computing performance of electronic circuits beyond the limits of current CMOS. Arrays offer both structural efficiency with reconfiguration and prospective capability of integration with different technologies. However, certain problems need to be addressed, and the most important one is the prevailing occurrence of faults. Considering fault rate projections as high as 20% that is much higher than those of CMOS, it is fair to expect sophisticated fault-tolerance methods. The focus of this survey article is the assessment and evaluation of these methods and related algorithms applied in logic mapping and configuration processes. As a start, we concisely explain reconfigurable nano-crossbar arrays with their fault characteristics and models. Following that, we demonstrate configuration techniques of the arrays in the presence of permanent faults and elaborate on two main fault-tolerance methodologies, namely defect-unaware and defect-aware approaches, with a short review on advantages and disadvantages. For both methodologies, we present detailed experimental results of related algorithms regarding their strengths and weaknesses with a comprehensive yield, success rate and runtime analysis. Next, we overview fault-tolerance approaches for transient faults. As a conclusion, we overview the proposed algorithms with future directions and upcoming challenges.This work is supported by the EU-H2020-RISE project NANOxCOMP no 691178 and the TUBITAK-Career project no 113E760

Multistage Packet-Switching Fabrics for Data Center Networks

Recent applications have imposed stringent requirements within the Data Center Network (DCN) switches in terms of scalability, throughput and latency. In this thesis, the architectural design of the packet-switches is tackled in different ways to enable the expansion in both the number of connected endpoints and traffic volume. A cost-effective Clos-network switch with partially buffered units is proposed and two packet scheduling algorithms are described. The first algorithm adopts many simple and distributed arbiters, while the second approach relies on a central arbiter to guarantee an ordered packet delivery. For an improved scalability, the Clos switch is build using a Network-on-Chip (NoC) fabric instead of the common crossbar units. The Clos-UDN architecture made with Input-Queued (IQ) Uni-Directional NoC modules (UDNs) simplifies the input line cards and obviates the need for the costly Virtual Output Queues (VOQs). It also avoids the need for complex, and synchronized scheduling processes, and offers speedup, load balancing, and good path diversity. Under skewed traffic, a reliable micro load-balancing contributes to boosting the overall network performance. Taking advantage of the NoC paradigm, a wrapped-around multistage switch with fully interconnected Central Modules (CMs) is proposed. The architecture operates with a congestion-aware routing algorithm that proactively distributes the traffic load across the switching modules, and enhances the switch performance under critical packet arrivals. The implementation of small on-chip buffers has been made perfectly feasible using the current technology. This motivated the implementation of a large switching architecture with an Output-Queued (OQ) NoC fabric. The design merges assets of the output queuing, and NoCs to provide high throughput, and smooth latency variations. An approximate analytical model of the switch performance is also proposed. To further exploit the potential of the NoC fabrics and their modularity features, a high capacity Clos switch with Multi-Directional NoC (MDN) modules is presented. The Clos-MDN switching architecture exhibits a more compact layout than the Clos-UDN switch. It scales better and faster in port count and traffic load. Results achieved in this thesis demonstrate the high performance, expandability and programmability features of the proposed packet-switches which makes them promising candidates for the next-generation data center networking infrastructure

Studies in Exascale Computer Architecture: Interconnect, Resiliency, and Checkpointing

Today’s supercomputers are built from the state-of-the-art components to extract as much performance as possible to solve the most computationally intensive problems in the world. Building the next generation of exascale supercomputers, however, would require re-architecting many of these components to extract over 50x more performance than the current fastest supercomputer in the United States. To contribute towards this goal, two aspects of the compute node architecture were examined in this thesis: the on-chip interconnect topology and the memory and storage checkpointing platforms. As a first step, a skeleton exascale system was modeled to meet 1 exaflop of performance along with 100 petabytes of main memory. The model revealed that large kilo-core processors would be necessary to meet the exaflop performance goal; existing topologies, however, would not scale to those levels. To address this new challenge, we investigated and proposed asymmetric high-radix topologies that decoupled local and global communications and used different radix routers for switching network traffic at each level. The proposed topologies scaled more readily to higher numbers of cores with better latency and energy consumption than before. The vast number of components that the model revealed would be needed in these exascale systems cautioned towards better fault tolerance mechanisms. To address this challenge, we showed that local checkpoints within the compute node can be saved to a hybrid DRAM and SSD platform in order to write them faster without wearing out the SSD or consuming a lot of energy. A hybrid checkpointing platform allowed more frequent checkpoints to be made without sacrificing performance. Subsequently, we proposed switching to a DIMM-based SSD in order to perform fine-grained I/O operations that would be integral in interleaving checkpointing and computation while still providing persistence guarantees. Two more techniques that consolidate and overlap checkpointing were designed to better hide the checkpointing latency to the SSD.PHDComputer Science & EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttps://deepblue.lib.umich.edu/bitstream/2027.42/137096/1/sabeyrat_1.pd

On Multicast in Asynchronous Networks-on-Chip: Techniques, Architectures, and FPGA Implementation

In this era of exascale computing, conventional synchronous design techniques are facing unprecedented challenges. The consumer electronics market is replete with many-core systems in the range of 16 cores to thousands of cores on chip, integrating multi-billion transistors. However, with this ever increasing complexity, the traditional design approaches are facing key issues such as increasing chip power, process variability, aging, thermal problems, and scalability. An alternative paradigm that has gained significant interest in the last decade is asynchronous design. Asynchronous designs have several potential advantages: they are naturally energy proportional, burning power only when active, do not require complex clock distribution, are robust to different forms of variability, and provide ease of composability for heterogeneous platforms. Networks-on-chip (NoCs) is an interconnect paradigm that has been introduced to deal with the ever-increasing system complexity. NoCs provide a distributed, scalable, and efficient interconnect solution for today’s many-core systems. Moreover, NoCs are a natural match with asynchronous design techniques, as they separate communication infrastructure and timing from the computational elements. To this end, globally-asynchronous locally-synchronous (GALS) systems that interconnect multiple processing cores, operating at different clock speeds, using an asynchronous NoC, have gained significant interest. While asynchronous NoCs have several advantages, they also face a key challenge of supporting new types of traffic patterns. Once such pattern is multicast communication, where a source sends packets to arbitrary number of destinations. Multicast is not only common in parallel computing, such as for cache coherency, but also for emerging areas such as neuromorphic computing. This important capability has been largely missing from asynchronous NoCs. This thesis introduces several efficient multicast solutions for these interconnects. In particular, techniques, and network architectures are introduced to support high-performance and low-power multicast. Two leading network topologies are the focus: a variant mesh-of-trees (MoT) and a 2D mesh. In addition, for a more realistic implementation and analysis, as well as significantly advancing the field of asynchronous NoCs, this thesis also targets synthesis of these NoCs on commercial FPGAs. While there has been significant advances in FPGA technologies, there has been only limited research on implementing asynchronous NoCs on FPGAs. To this end, a systematic computeraided design (CAD) methodology has been introduced to efficiently and safely map asynchronous NoCs on FPGAs. Overall, this thesis makes the following three contributions. The first contribution is a multicast solution for a variant MoT network topology. This topology consists of simple low-radix switches, and has been used in high-performance computing platforms. A novel local speculation technique is introduced, where a subset of the network’s switches are speculative that always broadcast every packet. These switches are very simple and have high performance. Speculative switches are surrounded by non-speculative ones that route packets based on their destinations and also throttle any redundant copies created by the former. This hybrid network architecture achieved significant performance and power benefits over other multicast approaches. The second contribution is a multicast solution for a 2D-mesh topology, which is more complex with higher-radix switches and also is more commonly used. A novel continuous-time replication strategy is introduced to optimize the critical multi-way forking operation of a multicast transmission. In this technique, a multicast packet is first stored in an input port of a switch, from where it is sent through distinct output ports towards different destinations concurrently, at each output’s own rate and in continuous time. This strategy is shown to have significant latency and energy benefits over an approach that performs multicast using multiple distinct serial unicasts to each destination. Finally, a systematic CAD methodology is introduced to synthesize asynchronous NoCs on commercial FPGAs. A two-fold goal is targeted: correctness and high performance. For ease of implementation, only existing FPGA synthesis tools are used. Moreover, since asynchronous NoCs involve special asynchronous components, a comprehensive guide is introduced to map these elements correctly and efficiently. Two asynchronous NoC switches are synthesized using the proposed approach on a leading Xilinx FPGA in 28 nm: one that only handles unicast, and the other that also supports multicast. Both showed significant energy benefits with some performance gains over a state-of-the-art synchronous switch

Multistage Packet-Switching Fabrics for Data Center Networks

Recent applications have imposed stringent requirements within the Data Center Network (DCN) switches in terms of scalability, throughput and latency. In this thesis, the architectural design of the packet-switches is tackled in different ways to enable the expansion in both the number of connected endpoints and traffic volume. A cost-effective Clos-network switch with partially buffered units is proposed and two packet scheduling algorithms are described. The first algorithm adopts many simple and distributed arbiters, while the second approach relies on a central arbiter to guarantee an ordered packet delivery. For an improved scalability, the Clos switch is build using a Network-on-Chip (NoC) fabric instead of the common crossbar units. The Clos-UDN architecture made with Input-Queued (IQ) Uni-Directional NoC modules (UDNs) simplifies the input line cards and obviates the need for the costly Virtual Output Queues (VOQs). It also avoids the need for complex, and synchronized scheduling processes, and offers speedup, load balancing, and good path diversity. Under skewed traffic, a reliable micro load-balancing contributes to boosting the overall network performance. Taking advantage of the NoC paradigm, a wrapped-around multistage switch with fully interconnected Central Modules (CMs) is proposed. The architecture operates with a congestion-aware routing algorithm that proactively distributes the traffic load across the switching modules, and enhances the switch performance under critical packet arrivals. The implementation of small on-chip buffers has been made perfectly feasible using the current technology. This motivated the implementation of a large switching architecture with an Output-Queued (OQ) NoC fabric. The design merges assets of the output queuing, and NoCs to provide high throughput, and smooth latency variations. An approximate analytical model of the switch performance is also proposed. To further exploit the potential of the NoC fabrics and their modularity features, a high capacity Clos switch with Multi-Directional NoC (MDN) modules is presented. The Clos-MDN switching architecture exhibits a more compact layout than the Clos-UDN switch. It scales better and faster in port count and traffic load. Results achieved in this thesis demonstrate the high performance, expandability and programmability features of the proposed packet-switches which makes them promising candidates for the next-generation data center networking infrastructure

Design and Evaluation of a Hardware System for Online Signal Processing within Mobile Brain-Computer Interfaces

Brain-Computer Interfaces (BCIs) sind innovative Systeme, die eine direkte Kommunikation zwischen dem Gehirn und externen Geräten ermöglichen. Diese Schnittstellen haben sich zu einer transformativen Lösung nicht nur für Menschen mit neurologischen Verletzungen entwickelt, sondern auch für ein breiteres Spektrum von Menschen, das sowohl medizinische als auch nicht-medizinische Anwendungen umfasst. In der Vergangenheit hat die Herausforderung, dass neurologische Verletzungen nach einer anfänglichen Erholungsphase statisch bleiben, die Forscher dazu veranlasst, innovative Wege zu beschreiten. Seit den 1970er Jahren stehen BCIs an vorderster Front dieser Bemühungen. Mit den Fortschritten in der Forschung haben sich die BCI-Anwendungen erweitert und zeigen ein großes Potenzial für eine Vielzahl von Anwendungen, auch für weniger stark eingeschränkte (zum Beispiel im Kontext von Hörelektronik) sowie völlig gesunde Menschen (zum Beispiel in der Unterhaltungsindustrie). Die Zukunft der BCI-Forschung hängt jedoch auch von der Verfügbarkeit zuverlässiger BCI-Hardware ab, die den Einsatz in der realen Welt gewährleistet. Das im Rahmen dieser Arbeit konzipierte und implementierte CereBridge-System stellt einen bedeutenden Fortschritt in der Brain-Computer-Interface-Technologie dar, da es die gesamte Hardware zur Erfassung und Verarbeitung von EEG-Signalen in ein mobiles System integriert. Die Architektur der Verarbeitungshardware basiert auf einem FPGA mit einem ARM Cortex-M3 innerhalb eines heterogenen ICs, was Flexibilität und Effizienz bei der EEG-Signalverarbeitung gewährleistet. Der modulare Aufbau des Systems, bestehend aus drei einzelnen Boards, gewährleistet die Anpassbarkeit an unterschiedliche Anforderungen. Das komplette System wird an der Kopfhaut befestigt, kann autonom arbeiten, benötigt keine externe Interaktion und wiegt einschließlich der 16-Kanal-EEG-Sensoren nur ca. 56 g. Der Fokus liegt auf voller Mobilität. Das vorgeschlagene anpassbare Datenflusskonzept erleichtert die Untersuchung und nahtlose Integration von Algorithmen und erhöht die Flexibilität des Systems. Dies wird auch durch die Möglichkeit unterstrichen, verschiedene Algorithmen auf EEG-Daten anzuwenden, um unterschiedliche Anwendungsziele zu erreichen. High-Level Synthesis (HLS) wurde verwendet, um die Algorithmen auf das FPGA zu portieren, was den Algorithmenentwicklungsprozess beschleunigt und eine schnelle Implementierung von Algorithmusvarianten ermöglicht. Evaluierungen haben gezeigt, dass das CereBridge-System in der Lage ist, die gesamte Signalverarbeitungskette zu integrieren, die für verschiedene BCI-Anwendungen erforderlich ist. Darüber hinaus kann es mit einer Batterie von mehr als 31 Stunden Dauerbetrieb betrieben werden, was es zu einer praktikablen Lösung für mobile Langzeit-EEG-Aufzeichnungen und reale BCI-Studien macht. Im Vergleich zu bestehenden Forschungsplattformen bietet das CereBridge-System eine bisher unerreichte Leistungsfähigkeit und Ausstattung für ein mobiles BCI. Es erfüllt nicht nur die relevanten Anforderungen an ein mobiles BCI-System, sondern ebnet auch den Weg für eine schnelle Übertragung von Algorithmen aus dem Labor in reale Anwendungen. Im Wesentlichen liefert diese Arbeit einen umfassenden Entwurf für die Entwicklung und Implementierung eines hochmodernen mobilen EEG-basierten BCI-Systems und setzt damit einen neuen Standard für BCI-Hardware, die in der Praxis eingesetzt werden kann.Brain-Computer Interfaces (BCIs) are innovative systems that enable direct communication between the brain and external devices. These interfaces have emerged as a transformative solution not only for individuals with neurological injuries, but also for a broader range of individuals, encompassing both medical and non-medical applications. Historically, the challenge of neurological injury being static after an initial recovery phase has driven researchers to explore innovative avenues. Since the 1970s, BCIs have been at one forefront of these efforts. As research has progressed, BCI applications have expanded, showing potential in a wide range of applications, including those for less severely disabled (e.g. in the context of hearing aids) and completely healthy individuals (e.g. entertainment industry). However, the future of BCI research also depends on the availability of reliable BCI hardware to ensure real-world application. The CereBridge system designed and implemented in this work represents a significant leap forward in brain-computer interface technology by integrating all EEG signal acquisition and processing hardware into a mobile system. The processing hardware architecture is centered around an FPGA with an ARM Cortex-M3 within a heterogeneous IC, ensuring flexibility and efficiency in EEG signal processing. The modular design of the system, consisting of three individual boards, ensures adaptability to different requirements. With a focus on full mobility, the complete system is mounted on the scalp, can operate autonomously, requires no external interaction, and weighs approximately 56g, including 16 channel EEG sensors. The proposed customizable dataflow concept facilitates the exploration and seamless integration of algorithms, increasing the flexibility of the system. This is further underscored by the ability to apply different algorithms to recorded EEG data to meet different application goals. High-Level Synthesis (HLS) was used to port algorithms to the FPGA, accelerating the algorithm development process and facilitating rapid implementation of algorithm variants. Evaluations have shown that the CereBridge system is capable of integrating the complete signal processing chain required for various BCI applications. Furthermore, it can operate continuously for more than 31 hours with a 1800mAh battery, making it a viable solution for long-term mobile EEG recording and real-world BCI studies. Compared to existing research platforms, the CereBridge system offers unprecedented performance and features for a mobile BCI. It not only meets the relevant requirements for a mobile BCI system, but also paves the way for the rapid transition of algorithms from the laboratory to real-world applications. In essence, this work provides a comprehensive blueprint for the development and implementation of a state-of-the-art mobile EEG-based BCI system, setting a new benchmark in BCI hardware for real-world applicability

Deadlock avoidance with virtual channels

High Performance Computing is a rapidly evolving area of computer science which attends to solve complicated computational problems with the combination of computational nodes connected through high speed networks. This work concentrates on the networks problems that appear in such networks and specially focuses on the Deadlock problem that can decrease the efficiency of the communication or even destroy the balance and paralyze the network. Goal of this work is the Deadlock avoidance with the use of virtual channels, in the switches of the network where the problem appears. The deadlock avoidance assures that will not be loss of data inside network, having as result the increased latency of the served packets, due to the extra calculation that the switches have to make to apply the policy.La computación de alto rendimiento es una zona de rápida evolución de la informática que busca resolver complicados problemas de cálculo con la combinación de los nodos de cómputo conectados a través de redes de alta velocidad. Este trabajo se centra en los problemas de las redes que aparecen en este tipo de sistemas y especialmente se centra en el problema del "deadlock" que puede disminuir la eficacia de la comunicación con la paralización de la red. El objetivo de este trabajo es la evitación de deadlock con el uso de canales virtuales, en los conmutadores de la red donde aparece el problema. Evitar el deadlock asegura que no se producirá la pérdida de datos en red, teniendo como resultado el aumento de la latencia de los paquetes, debido al overhead extra de cálculo que los conmutadores tienen que hacer para aplicar la política.La computació d'alt rendiment és una àrea de ràpida evolució de la informàtica que pretén resoldre complicats problemes de càlcul amb la combinació de nodes de còmput connectats a través de xarxes d'alta velocitat. Aquest treball se centra en els problemes de les xarxes que apareixen en aquest tipus de sistemes i especialment se centra en el problema del "deadlock" que pot disminuir l'eficàcia de la comunicació amb la paralització de la xarxa. L'objectiu d'aquest treball és l'evitació de deadlock amb l'ús de canals virtuals, en els commutadors de la xarxa on apareix el problema. Evitar deadlock assegura que no es produirà la pèrdua de dades en xarxa, tenint com a resultat l'augment de la latència dels paquets, degut al overhead extra de càlcul que els commutadors han de fer per aplicar la política

Design and performance optimization of asynchronous networks-on-chip

As digital systems continue to grow in complexity, the design of conventional synchronous systems is facing unprecedented challenges. The number of transistors on individual chips is already in the multi-billion range, and a greatly increasing number of components are being integrated onto a single chip. As a consequence, modern digital designs are under strong time-to-market pressure, and there is a critical need for composable design approaches for large complex systems. In the past two decades, networks-on-chip (NoC’s) have been a highly active research area. In a NoC-based system, functional blocks are first designed individually and may run at different clock rates. These modules are then connected through a structured network for on-chip global communication. However, due to the rigidity of centrally-clocked NoC’s, there have been bottlenecks of system scalability, energy and performance, which cannot be easily solved with synchronous approaches. As a result, there has been significant recent interest in combing the notion of asynchrony with NoC designs. Since the NoC approach inherently separates the communication infrastructure, and its timing, from computational elements, it is a natural match for an asynchronous paradigm. Asynchronous NoC’s, therefore, enable a modular and extensible system composition for an ‘object-orient’ design style. The thesis aims to significantly advance the state-of-art and viability of asynchronous and globally-asynchronous locally-synchronous (GALS) networks-on-chip, to enable high-performance and low-energy systems. The proposed asynchronous NoC’s are nearly entirely based on standard cells, which eases their integration into industrial design flows. The contributions are instantiated in three different directions. First, practical acceleration techniques are proposed for optimizing the system latency, in order to break through the latency bottleneck in the memory interfaces of many on-chip parallel processors. Novel asynchronous network protocols are proposed, along with concrete NoC designs. A new concept, called ‘monitoring network’, is introduced. Monitoring networks are lightweight shadow networks used for fast-forwarding anticipated traffic information, ahead of the actual packet traffic. The routers are therefore allowed to initiate and perform arbitration and channel allocation in advance. The technique is successfully applied to two topologies which belong to two different categories – a variant mesh-of-trees (MoT) structure and a 2D-mesh topology. Considerable and stable latency improvements are observed across a wide range of traffic patterns, along with moderate throughput gains. Second, for the first time, a high-performance and low-power asynchronous NoC router is compared directly to a leading commercial synchronous counterpart in an advanced industrial technology. The asynchronous router design shows significant performance improvements, as well as area and power savings. The proposed asynchronous router integrates several advanced techniques, including a low-latency circular FIFO for buffer design, and a novel end-to-end credit-based virtual channel (VC) flow control. In addition, a semi-automated design flow is created, which uses portions of a standard synchronous tool flow. Finally, a high-performance multi-resource asynchronous arbiter design is developed. This small but important component can be directly used in existing asynchronous NoC’s for performance optimization. In addition, this standalone design promises use in opening up new NoC directions, as well as for general use in parallel systems. In the proposed arbiter design, the allocation of a resource to a client is divided into several steps. Multiple successive client-resource pairs can be selected rapidly in pipelined sequence, and the completion of the assignments can overlap in parallel. In sum, the thesis provides a set of advanced design solutions for performance optimization of asynchronous and GALS networks-on-chip. These solutions are at different levels, from network protocols, down to router- and component-level optimizations, which can be directly applied to existing basic asynchronous NoC designs to provide a leap in performance improvement