Design of a tunable multi-band differential LC VCO using 0.35 mu m SiGe BiCMOS technology for multi-standard wireless communication systems

In this paper, an integrated 2.2-5.7GHz multi-band differential LC VCO for multi-standard wireless communication systems was designed utilizing 0.35 mu m SiGe BiCMOS technology. The topology, which combines the switching inductors and capacitors together in the same circuit, is a novel approach for wideband VCOs. Based on the post-layout simulation results, the VCO can be tuned using a DC voltage of 0 to 3.3 V for 5 different frequency bands (2.27-2.51 GHz, 2.48-2.78 GHz, 3.22-3.53 GHz, 3.48-3.91 GHz and 4.528-5.7 GHz) with a maximum bandwidth of 1.36 GHz and a minimum bandwidth of 300 MHz. The designed and simulated VCO can generate a differential output power between 0.992 and -6.087 dBm with an average power consumption of 44.21 mW including the buffers. The average second and third harmonics level were obtained as -37.21 and -47.6 dBm, respectively. The phase noise between -110.45 and -122.5 dBc/Hz, that was simulated at 1 MHz offset, can be obtained through the frequency of interest. Additionally, the figure of merit (FOM), that includes all important parameters such as the phase noise, the power consumption and the ratio of the operating frequency to the offset frequency, is between -176.48 and -181.16 and comparable or better than the ones with the other current VCOs. The main advantage of this study in comparison with the other VCOs, is covering 5 frequency bands starting from 2.27 up to 5.76 GHz without FOM and area abandonment. Output power of the fundamental frequency changes between -6.087 and 0.992 dBm, depending on the bias conditions (operating bands). Based on the post-layout simulation results, the core VCO circuit draws a current between 2.4-6.3 mA and between 11.4 and 15.3 mA with the buffer circuit from 3.3 V supply. The circuit occupies an area of 1.477 mm(2) on Si substrate, including DC, digital and RF pads

A Noise-Shifting Differential Colpitts VCO

A novel noise-shifting differential Colpitts VCO is presented. It uses current switching to lower phase noise by cyclostationary noise alignment and improve the start-up condition. A design strategy is also devised to enhance the phase noise performance of quadrature coupled oscillators. Two integrated VCOs are presented as design examples

LC-VCO design optimization methodology based on the gm/ID ratio for nanometer CMOS technologies

In this paper, an LC voltage-controlled oscillator (LC-VCO) design optimization methodology based on the gm/ID technique and on the exploration of all inversion regions of the MOS transistor (MOST) is presented. An in-depth study of the compromises between phase noise and current consumption permits optimization of the design for given specifications. Semiempirical models of MOSTs and inductors, obtained by simulation, jointly with analytical phase noise models, allow to get a design space map where the design tradeoffs are easily identified. Four LC-VCO designs in different inversion regions in a 90-nm CMOS process are obtained with the proposed methodology and verified with electrical simulations. Finally, the implementation and measurements are presented for a 2.4-GHz VCO operating in moderate inversion. The designed VCO draws 440 μA from a 1.2-V power supply and presents a phase noise of -106.2 dBc/Hz at 400 kHz from the carrier

Voltage controlled oscillator for mm-wave radio systems

Abstract. The advancement in silicon technology has accelerated the development of integrated millimeter-wave transceiver systems operating up to 100 GHz with sophisticated functionality at a reduced consumer cost. Due to the progress in the field of signal processing, frequency modulated continuous wave (FMCW) radar has become common in recent years. A high-performance local oscillator (LO) is required to generate reference signals utilized in these millimeter-wave radar transceivers. To accomplish this, novel design techniques in fundamental voltage controlled oscillators (VCO) are necessary to achieve low phase noise, wide frequency tuning range, and good power efficiency. Although integrated VCOs have been studied for decades, as we move higher in the radio frequency spectrum, there are new trade-offs in the performance parameters that require further characterization. The work described in this thesis aims to design a fully integrated fundamental VCO targeting to 150 GHz, i.e., D-Band. The purpose is to observe and analyze the design limitations at these high frequencies and their corresponding trade-offs during the design procedure. The topology selected for this study is the cross-coupled LC tank VCO. For the study, two design topologies were considered: a conventional cross-coupled LC tank VCO and an inductive divider cross-coupled LC tank VCO. The conventional LC tank VCO yields better performance in terms of phase noise and tuning range. It is observed that the VCO is highly sensitive to parasitic contributions by the transistors, and the layout interconnects, thus limiting the targeted frequency range. The dimensions of the LC tank and the transistors are selected carefully. Moreover, the VCO performance is limited by the low Q factor of the LC tank governed by the varactor that is degrading the phase noise performance and the tuning range, respectively. The output buffer loaded capacitance and the core power consumption of the VCO are optimized. The layout is drawn carefully with strategies to minimize the parasitic effects. Considering all the design challenges, a 126 GHz VCO with a tuning range of 3.9% is designed. It achieves FOMT (Figure-of-merit) of -172 dBc/Hz, and phase noise of -99.14 dBc/Hz at 10 MHz offset, Core power consumption is 8.9 mW from a 1.2 V supply. Just falling short of the targeted frequency, the design is suitable for FMCW radar applications for future technologies. The design was done using Silicon-on-Insulator (SOI) CMOS technology

Investigation on LIGA-MEMS and on-chip CMOS capacitors for a VCO application

Modern communication systems require high performance radio frequency (RF) and microwave circuits and devices. This is becoming increasingly challenging to realize in the content of cost/size constraints. Integrated circuits (ICs) satisfy the cost/size requirement, but performance is often sacri¯ced. For instance, high quality factor (Q factor) passive components are difficult to achieve in standard silicon-based IC processes.In recent years, microelectromechanical systems (MEMS) devices have been receiving increasing attention as a possible replacement for various on-chip passive elements, offering potential improvement in performance while maintaining high levels of integration. Variable capacitors (varactor) are common elements used in various applications. One of the MEMS variable capacitors that has been recently developed is built using deep X-ray lithography (as part of the LIGA process). This type of capacitor exhibits high quality factor at microwave frequencies.The complementary metal oxide semiconductor (CMOS) technology dominates the silicon IC process. CMOS becomes increasingly popular for RF applications due to its advantages in level of integration, cost and power consumption. This research demonstrates a CMOS voltage-controlled oscillator (VCO) design which is used to investigate methods, advantages and problems in integrating LIGA-MEMS devices to CMOS RF circuits, and to evaluate the performance of the LIGA-MEMS variable capacitor in comparison with the conventional on-chip CMOS varactor. The VCO was designed and fabricated using TSMC 0.18 micron CMOS technology. The core of the VCO, including transistors, resistors, and on-chip inductors was designed to connect to either an on-chip CMOS varactor or an off-chip LIGA-MEMS capacitor to oscillate between 2.6 GHz and 2.7 GHz. Oscillator phase noise analysis is used to compare the performance between the two capacitors. The fabricated VCO occupied an area of 1 mm^2.This initial attempt at VCO fabrication did not produce a functional VCO, so the performance of the capacitors with the fabricated VCO could not be tested. However, the simulation results show that with this LIGA-MEMS capacitor, a 6.4 dB of phase noise improvement at 300 kHz offset from the carrier is possible in a CMOS-based VCO design

LC VCO tuning with parallel MOS-varactor in FDSM application

Oppgaven tar for seg LC-VCO (voltage controlled oscillator) og dens frekvens tuning ved hjelp av en varactor(variabel reactor) i dette tilfellet en variabel kapasitanse og hva slags potensialle denne LC-VCO'en har i en FDSM(frequency Delta-Sigma modulator) applikasjon. FDSM er en analog til digital konverterings teknikk med potensialet for veldig lav power operasjon siden data verdiene representeres i form av frekvenser

ACTIVE INDUCTOR BASED LOW PHASE NOISE VOLTAGE CONTROLLED OSCILLATOR

This paper proposed a fully MOS-based voltage-controlled oscillator (VCO) with tuning range and low phase noise, replacing the most often used NMOS-based inductor-capacitor tank arranged in cross-coupled topology with a high-Q active inductor. This study mainly focuses on VCO design using a MOS-based active inductor and is implemented and verified using UMC 180nm CMOS technology. The proposed VCO is resistorless and consists of an active inductor, two MOS capacitors, and the buffer circuits. The fundamental principle of this MOS-based VCO concept is to use MOS based inductor to replace the passive inductor, which is an active inductor that gives less area and low power usage. At 1 MHz frequency offset, the phase noise achieved by this proposed configuration is -102.78dBc/Hz. In the proposed VCO architecture, the frequency tuning range is 0.5GHz to 1.7GHz. This VCO design can accomplish this acceptable tuning range by altering the regulating voltage from 0.7V to 1.8V. This suggested architecture of proposed VCO design has the power consumption of 9mW with a 1.8V supply voltage. The suggested VCO has been shown to be a good fit for low-power RF circuit applications while preserving acceptable performance metrics