A Multiproject Chip Approach to the Teaching of Analog MOS LSI and VLSI

Multiproject chip implementation has been used in teaching analog MOS circuit design. After having worked with computer simulation and layout aids in homework problems, students designed novel circuits including several high performance op amps, an A/D converter, a switched capacitor filter, a 1 K dynamic RAM, and a variety of less conventional MOS circuits such as a VII converter, an AC/DC converter, an AM radio receiver, a digitally-controlled analog signal processor, and on-chip circuitry for measuring transistor capacitances. These circuits were laid out as part of an NMOS multiproject chip. Several of the designs exhibit a considerable degree of innovation; fabrication pending, computer simulation shows that some may be pushing the state of the art. Several designs are of interest to digital designers; in fact, the course has provided knowledge and technique needed for detailed digital circuit design at the gate level

Silicon-based distributed voltage-controlled oscillators

Distributed voltage-controlled oscillators (DVCOs) are presented as a new approach to the design of silicon VCOs at microwave frequencies. In this paper, the operation of distributed oscillators is analyzed and the general oscillation condition is derived, resulting in analytical expressions for the frequency and amplitude. Two tuning techniques for DVCOs are demonstrated, namely, the inherent-varactor tuning and delay-balanced current-steering tuning. A complete analysis of the tuning techniques is presented. CMOS and bipolar DVCOs have been designed and fabricated in a 0.35-μm BiCMOS process. A 10-GHz CMOS DVCO achieves a tuning range of 12% (9.3-10.5 GHz) and a phase noise of -103 dBc/Hz at 600 kHz offset from the carrier. The oscillator provides an output power of -4.5 dBm without any buffering, drawing 14 mA of dc current from a 2.5-V power supply. A 12-GHz bipolar DVCO consuming 6 mA from a 2.5-V power supply is also demonstrated. It has a tuning range of 26% with a phase noise of -99 dBc/Hz at 600 kHz offset from the carrier

Design considerations for a monolithic, GaAs, dual-mode, QPSK/QASK, high-throughput rate transceiver

A monolithic, GaAs, dual mode, quadrature amplitude shift keying and quadrature phase shift keying transceiver with one and two billion bits per second data rate is being considered to achieve a low power, small and ultra high speed communication system for satellite as well as terrestrial purposes. Recent GaAs integrated circuit achievements are surveyed and their constituent device types are evaluated. Design considerations, on an elemental level, of the entire modem are further included for monolithic realization with practical fabrication techniques. Numerous device types, with practical monolithic compatability, are used in the design of functional blocks with sufficient performances for realization of the transceiver

Metodologia Per la Caratterizzazione di amplificatori a basso rumore per UMTS

In questo lavoro si presenta una metodologia di progettazione elettronica a livello di sistema, affrontando il problema della caratterizzazione dello spazio di progetto dell' amplificatore a basso rumore costituente il primo stadio di un front end a conversione diretta per UMTS realizzato in tecnologia CMOS con lunghezza di canale .18u. La metodologia è sviluppata al fine di valutare in modo quantititativo le specifiche ottime di sistema per il front-end stesso e si basa sul concetto di Piattaforma Analogica, che prevede la costruzione di un modello di prestazioni per il blocco analogico basato su campionamento statistico di indici di prestazioni del blocco stesso, misurati tramite simulazione di dimensionamenti dei componenti attivi e passivi soddisfacenti un set di equazioni specifico della topologia circuitale. Gli indici di prestazioni vengono successivamente ulizzati per parametrizzare modelli comportamentali utilizzati nelle fasi di ottimizzazione a livello di sistema. Modelli comportamentali atti a rappresentare i sistemi RF sono stati pertanto studiati per ottimizzare la scelta delle metriche di prestazioni. L'ottimizzazione dei set di equazioni atti a selezionare le configurazione di interesse per il campionamento ha al tempo stesso richiesto l'approfondimento dei modelli di dispositivi attivi validi in tutte le regioni di funzionamento, e lo studio dettagliato della progettazione degli amplificatori a basso rumore basati su degenerazione induttiva. Inoltre, il problema della modellizzazione a livello di sistema degli effetti della comunicazione tra LNA e Mixer è stato affrontato proponendo e analizzando diverse soluzioni. Il lavoro ha permesso di condurre un'ottimizzazione del front-end UMTS, giungendo a specifiche ottime a livello di sistema per l'amplificatore stesso

A novel tuning technique for distributed voltage controlled oscillators

A novel current-steering delay-balanced tuning technique for distributed voltage controlled oscillators (DVCO) is demonstrated. This tuning technique is used to design a DVCO operating at 10 GHz in a 0.35 μm CMOS technology. The DVCO is continuously tunable between 9.9 and 10.3 GHz. Special attention is paid to the layout issues for the high frequency design

A 190 by 244 charge-coupled area image sensor with interline transfer organization

A 190 x 244 element charge coupled area image sensor has been designed, fabricated and tested. This sensor employs an interline transfer organization and buried n-channel technology. It features a novel on-chip charge integrator and a distributed floating gate amplifier for high and low light level applications. The X-Y element count has been chosen to establish the capability of producing an NTSC compatible video signal. The array size is also compatible with the Super 8 lens format. The first few sample devices have been successfully operated at full video bandwidth for both high and low light levels with the charge amplifier system

Advanced digital modulation: Communication techniques and monolithic GaAs technology

Communications theory and practice are merged with state-of-the-art technology in IC fabrication, especially monolithic GaAs technology, to examine the general feasibility of a number of advanced technology digital transmission systems. Satellite-channel models with (1) superior throughput, perhaps 2 Gbps; (2) attractive weight and cost; and (3) high RF power and spectrum efficiency are discussed. Transmission techniques possessing reasonably simple architectures capable of monolithic fabrication at high speeds were surveyed. This included a review of amplitude/phase shift keying (APSK) techniques and the continuous-phase-modulation (CPM) methods, of which MSK represents the simplest case

Study of a small solar probe /sunblazer/. part ii- spacecraft and payload design progress report, jul. 1, 1964 - jun. 30, 1965

Design considerations for Sunblazer solar probe and payloa