Optimizing Embedded Software of Self-Powered IoT Edge Devices for Transient Computing

IoT edge computing becomes increasingly popular as it can mitigate the burden of cloud servers significantly by offloading tasks from the cloud to the edge which contains the majority of IoT devices. Currently, there are trillions of edge devices all over the world, and this number keeps increasing. A vast amount of edge devices work under power-constrained scenarios such as for outdoor environmental monitoring. Considering the cost and sustainability, in the long run, self-powering through energy harvesting technology is preferred for these IoT edge devices. Nevertheless, a common and critical drawback of self-powered IoT edge devices is that their runtime states in volatile memory such as SRAM will be lost during the power outage. Thanks to the state-of-the-art non-volatile processor (NVP), the runtime volatile states can be saved into the on-chip non-volatile memory before the power outage and recovered when harvesting power becomes available. Yet the potential of a self-powered IoT edge device is still hindered by the intrinsic low energy efficiency and reliability. In order to fully exert the potentials of existing self-powered IoT edge devices, this dissertation aims at optimizing the energy efficiency and reliability of self-powered IoT edge devices through several software approaches. First, to prevent execution progress loss during the power outage, NVP-aware task schedulers are proposed to maximize the overall task execution progress especially for the atomic tasks of which the unfinished progress is subjected to loss regardless of having been checkpointed. Second, to minimize both the time and energy overheads of checkpointing operations on non-volatile memory, an intelligent checkpointing scheme is proposed which can not only ensure a successful checkpointing but also predict the necessity of conducting checkpointing to avoid excessive checkpointing overhead. Third, to avoid inappropriate runtime CPU clock frequency with low energy utility, a CPU frequency modulator is proposed which adjusts the runtime CPU clock frequency adaptively. Finally, to thrive in ultra-low harvesting power scenarios, a light-weight software paradigm is proposed to help maximize the energy extraction rate of the energy harvester and power regulator bundle. Besides, checkpointing is also optimized for more energy-efficient and light-weight operation

Enabling Reliable, Efficient, and Secure Computing for Energy Harvesting Powered IoT Devices

Energy harvesting is one of the most promising techniques to power devices for future generation IoT. While energy harvesting does not have longevity, safety, and recharging concerns like traditional batteries, its instability brings a new challenge to the embedded systems: the energy harvested from environment is usually weak and intermittent. With traditional CMOS based technology, whenever the power is off, the computation has to start from the very beginning. Compared with existing CMOS based memory devices, emerging non-volatile memory devices such as PCM and STT-RAM, have the benefits of sustaining the data even when there is no power. By checkpointing the processor's volatile state to non-volatile memory, a program can resume its execution immediately after power comes back on again instead of restarting from the very beginning with checkpointing techniques. However, checkpointing is not sufficient for energy harvesting systems. First, the program execution resumed from the last checkpoint might not execute correctly and causes inconsistency problem to the system. This problem is due to the inconsistency between volatile system state and non-volatile system state during checkpointing. Second, the process of checkpointing consumes a considerable amount of energy and time due to the slow and energy-consuming write operation of non-volatile memory. Finally, connecting to the internet poses many security issues to energy harvesting IoT devices. Traditional data encryption methods are both energy and time consuming which do not fit the resource constrained IoT devices. Therefore, a light-weight encryption method is in urgent need for securing IoT devices. Targeting those three challenges, this dissertation proposes three techniques to enable reliable, efficient, and secure computing in energy harvesting IoT devices. First, a consistency-aware checkpointing technique is proposed to avoid inconsistency errors generated from the inconsistency between volatile state and non-volatile state. Second, checkpoint aware hybrid cache architecture is proposed to guarantee reliable checkpointing while maintaining a low checkpointing overhead from cache. Finally, to ensure the security of energy harvesting IoT devices, an energy-efficient in-memory encryption implementation for protecting the IoT device is proposed which can quickly encrypts the data in non-volatile memory and protect the embedded system physical and on-line attacks

Transiently Powered Computers

Demand for compact, easily deployable, energy-efficient computers has driven the development of general-purpose transiently powered computers (TPCs) that lack both batteries and wired power, operating exclusively on energy harvested from their surroundings. TPCs\u27 dependence solely on transient, harvested power offers several important design-time benefits. For example, omitting batteries saves board space and weight while obviating the need to make devices physically accessible for maintenance. However, transient power may provide an unpredictable supply of energy that makes operation difficult. A predictable energy supply is a key abstraction underlying most electronic designs. TPCs discard this abstraction in favor of opportunistic computation that takes advantage of available resources. A crucial question is how should a software-controlled computing device operate if it depends completely on external entities for power and other resources? The question poses challenges for computation, communication, storage, and other aspects of TPC design. The main idea of this work is that software techniques can make energy harvesting a practicable form of power supply for electronic devices. Its overarching goal is to facilitate the design and operation of usable TPCs. This thesis poses a set of challenges that are fundamental to TPCs, then pairs these challenges with approaches that use software techniques to address them. To address the challenge of computing steadily on harvested power, it describes Mementos, an energy-aware state-checkpointing system for TPCs. To address the dependence of opportunistic RF-harvesting TPCs on potentially untrustworthy RFID readers, it describes CCCP, a protocol and system for safely outsourcing data storage to RFID readers that may attempt to tamper with data. Additionally, it describes a simulator that facilitates experimentation with the TPC model, and a prototype computational RFID that implements the TPC model. To show that TPCs can improve existing electronic devices, this thesis describes applications of TPCs to implantable medical devices (IMDs), a challenging design space in which some battery-constrained devices completely lack protection against radio-based attacks. TPCs can provide security and privacy benefits to IMDs by, for instance, cryptographically authenticating other devices that want to communicate with the IMD before allowing the IMD to use any of its battery power. This thesis describes a simplified IMD that lacks its own radio, saving precious battery energy and therefore size. The simplified IMD instead depends on an RFID-scale TPC for all of its communication functions. TPCs are a natural area of exploration for future electronic design, given the parallel trends of energy harvesting and miniaturization. This work aims to establish and evaluate basic principles by which TPCs can operate

Dependable Embedded Systems

This Open Access book introduces readers to many new techniques for enhancing and optimizing reliability in embedded systems, which have emerged particularly within the last five years. This book introduces the most prominent reliability concerns from today’s points of view and roughly recapitulates the progress in the community so far. Unlike other books that focus on a single abstraction level such circuit level or system level alone, the focus of this book is to deal with the different reliability challenges across different levels starting from the physical level all the way to the system level (cross-layer approaches). The book aims at demonstrating how new hardware/software co-design solution can be proposed to ef-fectively mitigate reliability degradation such as transistor aging, processor variation, temperature effects, soft errors, etc. Provides readers with latest insights into novel, cross-layer methods and models with respect to dependability of embedded systems; Describes cross-layer approaches that can leverage reliability through techniques that are pro-actively designed with respect to techniques at other layers; Explains run-time adaptation and concepts/means of self-organization, in order to achieve error resiliency in complex, future many core systems

Evaluation of STT-MRAM main memory for HPC and real-time systems

It is questionable whether DRAM will continue to scale and will meet the needs of next-generation systems. Therefore, significant effort is invested in research and development of novel memory technologies. One of the candidates for nextgeneration memory is Spin-Transfer Torque Magnetic Random Access Memory (STT-MRAM). STT-MRAM is an emerging non-volatile memory with a lot of potential that could be exploited for various requirements of different computing systems. Being a novel technology, STT-MRAM devices are already approaching DRAM in terms of capacity, frequency and device size. Special STT-MRAM features such as intrinsic radiation hardness, non-volatility, zero stand-by power and capability to function in extreme temperatures also make it particularly suitable for aerospace, avionics and automotive applications. Despite of being a conceivable alternative for main memory technology, to this day, academic research of STT-MRAM main memory remains marginal. This is mainly due to the unavailability of publicly available detailed timing parameters of this novel technology, which are required to perform a cycle accurate main memory simulation. Some researchers adopt simplistic memory models to simulate main memory, but such models can introduce significant errors in the analysis of the overall system performance. Therefore, detailed timing parameters are a must-have for any evaluation or architecture exploration study of STT-MRAM main memory. These detailed parameters are not publicly available because STT-MRAM manufacturers are reluctant to release any delicate information on the technology. This thesis demonstrates an approach to perform a cycle accurate simulation of STT-MRAM main memory, being the first to release detailed timing parameters of this technology from academia, essentially enabling researchers to conduct reliable system level simulation of STT-MRAM using widely accepted existing simulation infrastructure. Our results show that, in HPC domain STT-MRAM provide performance comparable to DRAM. Results from the power estimation indicates that STT-MRAM power consumption increases significantly for Activation/Precharge power while Burst power increases moderately and Background power does not deviate much from DRAM. The thesis includes detailed STT-MRAM main memory timing parameters to the main repositories of DramSim2 and Ramulator, two of the most widely used and accepted state-of-the-art main memory simulators. The STT-MRAM timing parameters that has been originated as a part of this thesis, are till date the only reliable and publicly available timing information on this memory technology published from academia. Finally, the thesis analyzes the feasibility of using STT-MRAM in real-time embedded systems by investigating STT-MRAM main memory impact on average system performance and WCET. STT-MRAM's suitability for the real-time embedded systems is validated on benchmarks provided by the European Space Agency (ESA), EEMBC Autobench and MediaBench suite by analyzing performance and WCET impact. In quantitative terms, our results show that STT-MRAM main memory in real-time embedded systems provides performance and WCET comparable to conventional DRAM, while opening up opportunities to exploit various advantages.Es cuestionable si DRAM continuará escalando y cumplirá con las necesidades de los sistemas de la próxima generación. Por lo tanto, se invierte un esfuerzo significativo en la investigación y el desarrollo de nuevas tecnologías de memoria. Uno de los candidatos para la memoria de próxima generación es la Spin-Transfer Torque Magnetic Random Access Memory (STT-MRAM). STT-MRAM es una memoria no volátil emergente con un gran potencial que podría ser explotada para diversos requisitos de diferentes sistemas informáticos. Al ser una tecnología novedosa, los dispositivos STT-MRAM ya se están acercando a la DRAM en términos de capacidad, frecuencia y tamaño del dispositivo. Las características especiales de STTMRAM, como la dureza intrínseca a la radiación, la no volatilidad, la potencia de reserva cero y la capacidad de funcionar en temperaturas extremas, también lo hacen especialmente adecuado para aplicaciones aeroespaciales, de aviónica y automotriz. A pesar de ser una alternativa concebible para la tecnología de memoria principal, hasta la fecha, la investigación académica de la memoria principal de STT-MRAM sigue siendo marginal. Esto se debe principalmente a la falta de disponibilidad de los parámetros de tiempo detallados públicamente disponibles de esta nueva tecnología, que se requieren para realizar un ciclo de simulación de memoria principal precisa. Algunos investigadores adoptan modelos de memoria simplistas para simular la memoria principal, pero tales modelos pueden introducir errores significativos en el análisis del rendimiento general del sistema. Por lo tanto, los parámetros de tiempo detallados son indispensables para cualquier evaluación o estudio de exploración de la arquitectura de la memoria principal de STT-MRAM. Estos parámetros detallados no están disponibles públicamente porque los fabricantes de STT-MRAM son reacios a divulgar información delicada sobre la tecnología. Esta tesis demuestra un enfoque para realizar un ciclo de simulación precisa de la memoria principal de STT-MRAM, siendo el primero en lanzar parámetros de tiempo detallados de esta tecnología desde la academia, lo que esencialmente permite a los investigadores realizar una simulación confiable a nivel de sistema de STT-MRAM utilizando una simulación existente ampliamente aceptada infraestructura. Nuestros resultados muestran que, en el dominio HPC, STT-MRAM proporciona un rendimiento comparable al de la DRAM. Los resultados de la estimación de potencia indican que el consumo de potencia de STT-MRAM aumenta significativamente para la activation/Precharge power, mientras que la Burst power aumenta moderadamente y la Background power no se desvía mucho de la DRAM. La tesis incluye parámetros detallados de temporización memoria principal de STT-MRAM a los repositorios principales de DramSim2 y Ramulator, dos de los simuladores de memoria principal más avanzados y más utilizados y aceptados. Los parámetros de tiempo de STT-MRAM que se han originado como parte de esta tesis, son hasta la fecha la única información de tiempo confiable y disponible al público sobre esta tecnología de memoria publicada desde la academia. Finalmente, la tesis analiza la viabilidad de usar STT-MRAM en real-time embedded systems mediante la investigación del impacto de la memoria principal de STT-MRAM en el rendimiento promedio del sistema y WCET. La idoneidad de STTMRAM para los real-time embedded systems se valida en los applicaciones proporcionados por la European Space Agency (ESA), EEMBC Autobench y MediaBench, al analizar el rendimiento y el impacto de WCET. En términos cuantitativos, nuestros resultados muestran que la memoria principal de STT-MRAM en real-time embedded systems proporciona un desempeño WCET comparable al de una memoria DRAM convencional, al tiempo que abre oportunidades para explotar varias ventajas

Gestión de jerarquías de memoria híbridas a nivel de sistema

Tesis inédita de la Universidad Complutense de Madrid, Facultad de Informática, Departamento de Arquitectura de Computadoras y Automática y de Ku Leuven, Arenberg Doctoral School, Faculty of Engineering Science, leída el 11/05/2017.In electronics and computer science, the term ‘memory’ generally refers to devices that are used to store information that we use in various appliances ranging from our PCs to all hand-held devices, smart appliances etc. Primary/main memory is used for storage systems that function at a high speed (i.e. RAM). The primary memory is often associated with addressable semiconductor memory, i.e. integrated circuits consisting of silicon-based transistors, used for example as primary memory but also other purposes in computers and other digital electronic devices. The secondary/auxiliary memory, in comparison provides program and data storage that is slower to access but offers larger capacity. Examples include external hard drives, portable flash drives, CDs, and DVDs. These devices and media must be either plugged in or inserted into a computer in order to be accessed by the system. Since secondary storage technology is not always connected to the computer, it is commonly used for backing up data. The term storage is often used to describe secondary memory. Secondary memory stores a large amount of data at lesser cost per byte than primary memory; this makes secondary storage about two orders of magnitude less expensive than primary storage. There are two main types of semiconductor memory: volatile and nonvolatile. Examples of non-volatile memory are ‘Flash’ memory (sometimes used as secondary, sometimes primary computer memory) and ROM/PROM/EPROM/EEPROM memory (used for firmware such as boot programs). Examples of volatile memory are primary memory (typically dynamic RAM, DRAM), and fast CPU cache memory (typically static RAM, SRAM, which is fast but energy-consuming and offer lower memory capacity per are a unit than DRAM). Non-volatile memory technologies in Si-based electronics date back to the 1990s. Flash memory is widely used in consumer electronic products such as cellphones and music players and NAND Flash-based solid-state disks (SSDs) are increasingly displacing hard disk drives as the primary storage device in laptops, desktops, and even data centers. The integration limit of Flash memories is approaching, and many new types of memory to replace conventional Flash memories have been proposed. The rapid increase of leakage currents in Silicon CMOS transistors with scaling poses a big challenge for the integration of SRAM memories. There is also the case of susceptibility to read/write failure with low power schemes. As a result of this, over the past decade, there has been an extensive pooling of time, resources and effort towards developing emerging memory technologies like Resistive RAM (ReRAM/RRAM), STT-MRAM, Domain Wall Memory and Phase Change Memory(PRAM). Emerging non-volatile memory technologies promise new memories to store more data at less cost than the expensive-to build silicon chips used by popular consumer gadgets including digital cameras, cell phones and portable music players. These new memory technologies combine the speed of static random-access memory (SRAM), the density of dynamic random-access memory (DRAM), and the non-volatility of Flash memory and so become very attractive as another possibility for future memory hierarchies. The research and information on these Non-Volatile Memory (NVM) technologies has matured over the last decade. These NVMs are now being explored thoroughly nowadays as viable replacements for conventional SRAM based memories even for the higher levels of the memory hierarchy. Many other new classes of emerging memory technologies such as transparent and plastic, three-dimensional(3-D), and quantum dot memory technologies have also gained tremendous popularity in recent years...En el campo de la informática, el término ‘memoria’ se refiere generalmente a dispositivos que son usados para almacenar información que posteriormente será usada en diversos dispositivos, desde computadoras personales (PC), móviles, dispositivos inteligentes, etc. La memoria principal del sistema se utiliza para almacenar los datos e instrucciones de los procesos que se encuentre en ejecución, por lo que se requiere que funcionen a alta velocidad (por ejemplo, DRAM). La memoria principal está implementada habitualmente mediante memorias semiconductoras direccionables, siendo DRAM y SRAM los principales exponentes. Por otro lado, la memoria auxiliar o secundaria proporciona almacenaje(para ficheros, por ejemplo); es más lenta pero ofrece una mayor capacidad. Ejemplos típicos de memoria secundaria son discos duros, memorias flash portables, CDs y DVDs. Debido a que estos dispositivos no necesitan estar conectados a la computadora de forma permanente, son muy utilizados para almacenar copias de seguridad. La memoria secundaria almacena una gran cantidad de datos aun coste menor por bit que la memoria principal, siendo habitualmente dos órdenes de magnitud más barata que la memoria primaria. Existen dos tipos de memorias de tipo semiconductor: volátiles y no volátiles. Ejemplos de memorias no volátiles son las memorias Flash (algunas veces usadas como memoria secundaria y otras veces como memoria principal) y memorias ROM/PROM/EPROM/EEPROM (usadas para firmware como programas de arranque). Ejemplos de memoria volátil son las memorias DRAM (RAM dinámica), actualmente la opción predominante a la hora de implementar la memoria principal, y las memorias SRAM (RAM estática) más rápida y costosa, utilizada para los diferentes niveles de cache. Las tecnologías de memorias no volátiles basadas en electrónica de silicio se remontan a la década de1990. Una variante de memoria de almacenaje por carga denominada como memoria Flash es mundialmente usada en productos electrónicos de consumo como telefonía móvil y reproductores de música mientras NAND Flash solid state disks(SSDs) están progresivamente desplazando a los dispositivos de disco duro como principal unidad de almacenamiento en computadoras portátiles, de escritorio e incluso en centros de datos. En la actualidad, hay varios factores que amenazan la actual predominancia de memorias semiconductoras basadas en cargas (capacitivas). Por un lado, se está alcanzando el límite de integración de las memorias Flash, lo que compromete su escalado en el medio plazo. Por otra parte, el fuerte incremento de las corrientes de fuga de los transistores de silicio CMOS actuales, supone un enorme desafío para la integración de memorias SRAM. Asimismo, estas memorias son cada vez más susceptibles a fallos de lectura/escritura en diseños de bajo consumo. Como resultado de estos problemas, que se agravan con cada nueva generación tecnológica, en los últimos años se han intensificado los esfuerzos para desarrollar nuevas tecnologías que reemplacen o al menos complementen a las actuales. Los transistores de efecto campo eléctrico ferroso (FeFET en sus siglas en inglés) se consideran una de las alternativas más prometedores para sustituir tanto a Flash (por su mayor densidad) como a DRAM (por su mayor velocidad), pero aún está en una fase muy inicial de su desarrollo. Hay otras tecnologías algo más maduras, en el ámbito de las memorias RAM resistivas, entre las que cabe destacar ReRAM (o RRAM), STT-RAM, Domain Wall Memory y Phase Change Memory (PRAM)...Depto. de Arquitectura de Computadores y AutomáticaFac. de InformáticaTRUEunpu

Evaluation of STT-MRAM main memory for HPC and real-time systems

It is questionable whether DRAM will continue to scale and will meet the needs of next-generation systems. Therefore, significant effort is invested in research and development of novel memory technologies. One of the candidates for nextgeneration memory is Spin-Transfer Torque Magnetic Random Access Memory (STT-MRAM). STT-MRAM is an emerging non-volatile memory with a lot of potential that could be exploited for various requirements of different computing systems. Being a novel technology, STT-MRAM devices are already approaching DRAM in terms of capacity, frequency and device size. Special STT-MRAM features such as intrinsic radiation hardness, non-volatility, zero stand-by power and capability to function in extreme temperatures also make it particularly suitable for aerospace, avionics and automotive applications. Despite of being a conceivable alternative for main memory technology, to this day, academic research of STT-MRAM main memory remains marginal. This is mainly due to the unavailability of publicly available detailed timing parameters of this novel technology, which are required to perform a cycle accurate main memory simulation. Some researchers adopt simplistic memory models to simulate main memory, but such models can introduce significant errors in the analysis of the overall system performance. Therefore, detailed timing parameters are a must-have for any evaluation or architecture exploration study of STT-MRAM main memory. These detailed parameters are not publicly available because STT-MRAM manufacturers are reluctant to release any delicate information on the technology. This thesis demonstrates an approach to perform a cycle accurate simulation of STT-MRAM main memory, being the first to release detailed timing parameters of this technology from academia, essentially enabling researchers to conduct reliable system level simulation of STT-MRAM using widely accepted existing simulation infrastructure. Our results show that, in HPC domain STT-MRAM provide performance comparable to DRAM. Results from the power estimation indicates that STT-MRAM power consumption increases significantly for Activation/Precharge power while Burst power increases moderately and Background power does not deviate much from DRAM. The thesis includes detailed STT-MRAM main memory timing parameters to the main repositories of DramSim2 and Ramulator, two of the most widely used and accepted state-of-the-art main memory simulators. The STT-MRAM timing parameters that has been originated as a part of this thesis, are till date the only reliable and publicly available timing information on this memory technology published from academia. Finally, the thesis analyzes the feasibility of using STT-MRAM in real-time embedded systems by investigating STT-MRAM main memory impact on average system performance and WCET. STT-MRAM's suitability for the real-time embedded systems is validated on benchmarks provided by the European Space Agency (ESA), EEMBC Autobench and MediaBench suite by analyzing performance and WCET impact. In quantitative terms, our results show that STT-MRAM main memory in real-time embedded systems provides performance and WCET comparable to conventional DRAM, while opening up opportunities to exploit various advantages.Es cuestionable si DRAM continuará escalando y cumplirá con las necesidades de los sistemas de la próxima generación. Por lo tanto, se invierte un esfuerzo significativo en la investigación y el desarrollo de nuevas tecnologías de memoria. Uno de los candidatos para la memoria de próxima generación es la Spin-Transfer Torque Magnetic Random Access Memory (STT-MRAM). STT-MRAM es una memoria no volátil emergente con un gran potencial que podría ser explotada para diversos requisitos de diferentes sistemas informáticos. Al ser una tecnología novedosa, los dispositivos STT-MRAM ya se están acercando a la DRAM en términos de capacidad, frecuencia y tamaño del dispositivo. Las características especiales de STTMRAM, como la dureza intrínseca a la radiación, la no volatilidad, la potencia de reserva cero y la capacidad de funcionar en temperaturas extremas, también lo hacen especialmente adecuado para aplicaciones aeroespaciales, de aviónica y automotriz. A pesar de ser una alternativa concebible para la tecnología de memoria principal, hasta la fecha, la investigación académica de la memoria principal de STT-MRAM sigue siendo marginal. Esto se debe principalmente a la falta de disponibilidad de los parámetros de tiempo detallados públicamente disponibles de esta nueva tecnología, que se requieren para realizar un ciclo de simulación de memoria principal precisa. Algunos investigadores adoptan modelos de memoria simplistas para simular la memoria principal, pero tales modelos pueden introducir errores significativos en el análisis del rendimiento general del sistema. Por lo tanto, los parámetros de tiempo detallados son indispensables para cualquier evaluación o estudio de exploración de la arquitectura de la memoria principal de STT-MRAM. Estos parámetros detallados no están disponibles públicamente porque los fabricantes de STT-MRAM son reacios a divulgar información delicada sobre la tecnología. Esta tesis demuestra un enfoque para realizar un ciclo de simulación precisa de la memoria principal de STT-MRAM, siendo el primero en lanzar parámetros de tiempo detallados de esta tecnología desde la academia, lo que esencialmente permite a los investigadores realizar una simulación confiable a nivel de sistema de STT-MRAM utilizando una simulación existente ampliamente aceptada infraestructura. Nuestros resultados muestran que, en el dominio HPC, STT-MRAM proporciona un rendimiento comparable al de la DRAM. Los resultados de la estimación de potencia indican que el consumo de potencia de STT-MRAM aumenta significativamente para la activation/Precharge power, mientras que la Burst power aumenta moderadamente y la Background power no se desvía mucho de la DRAM. La tesis incluye parámetros detallados de temporización memoria principal de STT-MRAM a los repositorios principales de DramSim2 y Ramulator, dos de los simuladores de memoria principal más avanzados y más utilizados y aceptados. Los parámetros de tiempo de STT-MRAM que se han originado como parte de esta tesis, son hasta la fecha la única información de tiempo confiable y disponible al público sobre esta tecnología de memoria publicada desde la academia. Finalmente, la tesis analiza la viabilidad de usar STT-MRAM en real-time embedded systems mediante la investigación del impacto de la memoria principal de STT-MRAM en el rendimiento promedio del sistema y WCET. La idoneidad de STTMRAM para los real-time embedded systems se valida en los applicaciones proporcionados por la European Space Agency (ESA), EEMBC Autobench y MediaBench, al analizar el rendimiento y el impacto de WCET. En términos cuantitativos, nuestros resultados muestran que la memoria principal de STT-MRAM en real-time embedded systems proporciona un desempeño WCET comparable al de una memoria DRAM convencional, al tiempo que abre oportunidades para explotar varias ventajas.Postprint (published version

Towards Successful Application of Phase Change Memories: Addressing Challenges from Write Operations

The emerging Phase Change Memory (PCM) technology is drawing increasing attention due to its advantages in non-volatility, byte-addressability and scalability. It is regarded as a promising candidate for future main memory. However, PCM's write operation has some limitations that pose challenges to its application in memory. The disadvantages include long write latency, high write power and limited write endurance. In this thesis, I present my effort towards successful application of PCM memory. My research consists of several optimizing techniques at both the circuit and architecture level. First, at the circuit level, I propose Differential Write to remove unnecessary bit changes in PCM writes. This is not only beneficial to endurance but also to the energy and latency of writes. Second, I propose two memory scheduling enhancements (AWP and RAWP) for a non-blocking bank design. My memory scheduling enhancements can exploit intra-bank parallelism provided by non-blocking bank design, and achieve significant throughput improvement. Third, I propose Bit Level Power Budgeting (BPB), a fine-grained power budgeting technique that leverages the information from Differential Write to achieve even higher memory throughput under the same power budget. Fourth, I propose techniques to improve the QoS tuning ability of high-priority applications when running on PCM memory. In summary, the techniques I propose effectively address the challenges of PCM's write operations. In addition, I present the experimental infrastructure in this work and my visions of potential future research topics, which could be helpful to other researchers in the area

Sophisticated Batteryless Sensing

Wireless embedded sensing systems have revolutionized scientific, industrial, and consumer applications. Sensors have become a fixture in our daily lives, as well as the scientific and industrial communities by allowing continuous monitoring of people, wildlife, plants, buildings, roads and highways, pipelines, and countless other objects. Recently a new vision for sensing has emerged---known as the Internet-of-Things (IoT)---where trillions of devices invisibly sense, coordinate, and communicate to support our life and well being. However, the sheer scale of the IoT has presented serious problems for current sensing technologies---mainly, the unsustainable maintenance, ecological, and economic costs of recycling or disposing of trillions of batteries. This energy storage bottleneck has prevented massive deployments of tiny sensing devices at the edge of the IoT. This dissertation explores an alternative---leave the batteries behind, and harvest the energy required for sensing tasks from the environment the device is embedded in. These sensors can be made cheaper, smaller, and will last decades longer than their battery powered counterparts, making them a perfect fit for the requirements of the IoT. These sensors can be deployed where battery powered sensors cannot---embedded in concrete, shot into space, or even implanted in animals and people. However, these batteryless sensors may lose power at any point, with no warning, for unpredictable lengths of time. Programming, profiling, debugging, and building applications with these devices pose significant challenges. First, batteryless devices operate in unpredictable environments, where voltages vary and power failures can occur at any time---often devices are in failure for hours. Second, a device\u27s behavior effects the amount of energy they can harvest---meaning small changes in tasks can drastically change harvester efficiency. Third, the programming interfaces of batteryless devices are ill-defined and non- intuitive; most developers have trouble anticipating the problems inherent with an intermittent power supply. Finally, the lack of community, and a standard usable hardware platform have reduced the resources and prototyping ability of the developer. In this dissertation we present solutions to these challenges in the form of a tool for repeatable and realistic experimentation called Ekho, a reconfigurable hardware platform named Flicker, and a language and runtime for timely execution of intermittent programs called Mayfly