Concurrent optimization strategies for high-performance VLSI circuits

In the next generation of VLSI circuits, concurrent optimizations will be essential to achieve the performance challenges. In this dissertation, we present techniques for combining traditional timing optimization techniques to achieve a superior performance;The method of buffer insertion is used in timing optimization to either increase the driving power of a path in a circuit, or to isolate large capacitive loads that lie on noncritical or less critical paths. The procedure of transistor sizing selects the sizes of transistors within a circuit to achieve a given timing specification. Traditional design techniques perform these two optimizations as independent steps during synthesis, even though they are intimately linked and performing them in alternating steps is liable to lead to suboptimal solutions. The first part of this thesis presents a new approach for unifying transistor sizing with buffer insertion. Our algorithm achieve from 5% to 49% area reduction compared with the results of a standard transistor sizing algorithm;The next part of the thesis deals with the problem of collapsing gates for technology mapping. Two new techniques are proposed. The first method, the odd-level transistor replacement (OTR) method, performs technology mapping without the restriction of a fixed library size, and maps a circuit to a virtual library of complex static CMOS gates. The second technique, the Static CMOS/PTL method, uses a mix of static CMOS and pass transistor logic (PTL) to realize the circuit, using the relation between PTL and binary decision diagrams. The methods are very efficient and can handle all ISCAS\u2785 benchmark circuits in minutes. On average, it was found that the OTR method gave 40%, and the Static/PTL gave 50% delay reductions over SIS, with substantial area savings;Finally, we extend the technology mapping work to interleave it with placement in a single optimization. Conventional methods that perform these steps separately will not be adequate for next-generation circuits. Our approach presents an integrated solution to this problem, and shows an average of 28.19%, and a maximum of 78.42% improvement in the delay over a method that performs the two optimizations in separate steps

Stack Contention-alleviated Precharge Keeper for Pseudo Domino Logic

The dynamic circuits are supposed to offer superior speed and low power dissipation over static CMOS circuits. The domino logic circuits are used for high system performance but suffer from the precharge pulse degradation. This article provides different design topologies on the domino circuits to overcome the charge sharing and charge leakage with reference to the power dissipation and delay. The precharge keeper circuit has been proposed such that the keeper transistors also work as the precharge transistors to realize multiple output function. The performance improvement of the circuit\u27s analysis have been done for adders and logic gates using HSPICE tool. The proposed keeper techniques reveal lower power dissipation and lesser delay over the standard keeper circuit with less transistor count for different process variation

Stack Contention-alleviated Precharge Keeper for Pseudo Domino Logic

The dynamic circuits are supposed to offer superior speed and low power dissipation over static CMOS circuits. The domino logic circuits are used for high system performance but suffer from the precharge pulse degradation. This article provides different design topologies on the domino circuits to overcome the charge sharing and charge leakage with reference to the power dissipation and delay. The precharge keeper circuit has been proposed such that the keeper transistors also work as the precharge transistors to realize multiple output function. The performance improvement of the circuit’s analysis have been done for adders and logic gates using HSPICE tool. The proposed keeper techniques reveal lower power dissipation and lesser delay over the standard keeper circuit with less transistor count for different process variation

Silicon compilation

Silicon compilation is a term used for many different purposes. In this paper we define silicon compilation as a mapping from some higher level description into layout. We define the basic issues in structural and behavioral silicon compilation and some possible solutions to those issues. Finally, we define the concept of an intelligent silicon compiler in which the compiler evaluates the quality of the generated design and attempts to improve it if it is not satisfactory

High Current Matching over Full-Swing and Low-Glitch Charge Pump Circuit for PLLs

A high current matching over full-swing and low-glitch charge pump (CP) circuit is proposed. The current of the CP is split into two identical branches having one-half the original current. The two branches are connected in source-coupled structure, and a two-stage amplifier is used to regulate the common-source voltage for the minimum current mismatch. The proposed CP is designed in TSMC 0.18µm CMOS technology with a power supply of 1.8 V. SpectreRF based simulation results show the mismatch between the current source and the current sink is less than 0.1% while the current is 40 µA and output swing is 1.32 V ranging from 0.2 V to 1.52 V. Moreover, the transient output current presents nearly no glitches. The simulation results verify the usage of the CP in PLLs with the maximum tuning range from the voltage-controlled oscillator, as well as the low power supply applications

Pass-transistor very large scale integration

Logic elements are provided that permit reductions in layout size and avoidance of hazards. Such logic elements may be included in libraries of logic cells. A logical function to be implemented by the logic element is decomposed about logical variables to identify factors corresponding to combinations of the logical variables and their complements. A pass transistor network is provided for implementing the pass network function in accordance with this decomposition. The pass transistor network includes ordered arrangements of pass transistors that correspond to the combinations of variables and complements resulting from the logical decomposition. The logic elements may act as selection circuits and be integrated with memory and buffer elements

Design of Low Power Data Preserving Flip Flop Using MTCMOS Technique

In order to reduce overall power consumption, a well-known technique is to scale supply voltages. However, to maintain performance, device threshold voltages must scale as well, which will cause sub threshold leakage currents to increase exponentially. The sub threshold voltage has to affect the two parameters one is the delay and other one is the sub threshold leakage current. Smaller the threshold voltage smaller will be delay while larger will be the sub threshold current. Controlling sub threshold leakage has been explored significantly in the literature, especially in the context of reducing leakage currents in burst mode type circuits, where the system spends the majority of the time in an idle standby, or sleep, state where no computation is taking place. MTCMOS or multi-threshold CMOS has been proposed as a very effective technique for reducing leakage currents during the standby by state by utilizing high sleep devices to gate the power supplies of a low logic block. Although MTCMOS circuit techniques are effective for controlling leakage currents in combinational logic, a drawback is that it can cause internal nodes to float, and cannot be directly used in standard memory cells without corrupting stored data. As a result, several researchers have explored possible MTCMOS latch designs that can reduce leakage currents yet maintain state during the standby modes. In this work a data preserving flip flop with reduced leakage power is designed using MTCMOS technique in 90nm technology with the help of CADENCE tool. The simulation results have shown that the leakage power is reduced by 25.70% compared to CMOS flip flop

Adiabatic Approach for Low-Power Passive Near Field Communication Systems

This thesis tackles the need of ultra-low power electronics in the power limited passive Near Field Communication (NFC) systems. One of the techniques that has proven the potential of delivering low power operation is the Adiabatic Logic Technique. However, the low power benefits of the adiabatic circuits come with the challenges due to the absence of single opinion on the most energy efficient adiabatic logic family which constitute appropriate trade-offs between computation time, area and complexity based on the circuit and the power-clocking schemes. Therefore, five energy efficient adiabatic logic families working in single-phase, 2-phase and 4-phase power-clocking schemes were chosen. Since flip-flops are the basic building blocks of any sequential circuit and the existing flip-flops are MUX-based (having more transistors) design, therefore a novel single-phase, 2-phase and 4-phase reset based flip-flops were proposed. The performance of the multi-phase adiabatic families was evaluated and compared based on the design examples such as 2-bit ring counter, 3-bit Up-Down counter and 16-bit Cyclic Redundancy Check (CRC) circuit (benchmark circuit) based on ISO 14443-3A standard. Several trade-offs, design rules, and an appropriate range for the supply voltage scaling for multi-phase adiabatic logic are proposed. Furthermore, based on the NFC standard (ISO 14443-3A), data is frequently encoded using Manchester coding technique before transmitting it to the reader. Therefore, if Manchester encoding can be implemented using adiabatic logic technique, energy benefits are expected. However, adiabatic implementation of Manchester encoding presents a challenge. Therefore, a novel method for implementing Manchester encoding using adiabatic logic is proposed overcoming the challenges arising due to the AC power-clock. Other challenges that come with the dynamic nature of the adiabatic gates and the complexity of the 4-phase power-clocking scheme is in synchronizing the power-clock v phases and the time spent in designing, validation and debugging of errors. This requires a specific modelling approach to describe the adiabatic logic behaviour at the higher level of abstraction. However, describing adiabatic logic behaviour using Hardware Description Languages (HDLs) is a challenging problem due to the requirement of modelling the AC power-clock and the dual-rail inputs and outputs. Therefore, a VHDL-based modelling approach for the 4-phase adiabatic logic technique is developed for functional simulation, precise timing analysis and as an improvement over the previously described approaches

Digital Circuit Design Using Floating Gate Transistors

Floating gate (flash) transistors are used exclusively for memory applications today. These applications include SD cards of various form factors, USB flash drives and SSDs. In this thesis, we explore the use of flash transistors to implement digital logic circuits. Since the threshold voltage of flash transistors can be modified at a fine granularity during programming, several advantages are obtained by our flash-based digital circuit design approach. For one, speed binning at the factory can be controlled with precision. Secondly, an IC can be re-programmed in the field, to negate effects such as aging, which has been a significant problem in recent times, particularly for mission-critical applications. Thirdly, unlike a regular MOSFET, which has one threshold voltage level, a flash transistor can have multiple threshold voltage levels. The benefit of having multiple threshold voltage levels in a flash transistor is that it allows the ability to encode more symbols in each device, unlike a regular MOSFET. This allows us to implement multi-valued logic functions natively. In this thesis, we evaluate different flash-based digital circuit design approaches and compare their performance with a traditional CMOS standard cell-based design approach. We begin by evaluating our design approach at the cell level to optimize the design’s delay, power energy and physical area characteristics. The flash-based approach is demonstrated to be better than the CMOS standard cell approach, for these performance metrics. Afterwards, we present the performance of our design approach at the block level. We describe a synthesis flow to decompose a circuit block into a network of interconnected flash-based circuit cells. We also describe techniques to optimize the resulting network of flash-based circuit cells using don’t cares. Our optimization approach distinguishes itself from other optimization techniques that use don’t cares, since it a) targets a flash-based design flow, b) optimizes clusters of logic nodes at once instead of one node at a time, c) attempts to reduce the number of cubes instead of reducing the number of literals in each cube and d) performs optimization on the post-technology mapped netlist which results in a direct improvement in result quality, as compared to pre-technology mapping logic optimization that is typically done in the literature. The resulting network characteristics (delay, power, energy and physical area) are presented. These results are compared with a standard cell-based realization of the same block (obtained using commercial tools) and we demonstrate significant improvements in all the design metrics. We also study flash-based FPGA designs (both static and dynamic), and present the tradeoff of delay, power dissipation and energy consumption of the various designs. Our work differs from previously proposed flash-based FPGAs, since we embed the flash transistors (which store the configuration bits) directly within the logic and interconnect fabrics. We also present a detailed description of how the programming of the configuration bits is accomplished, for all the proposed designs