An Evaluation of 2-phase Charge Pump Topologies with Charge Transfer Switches for Green Mobile Technology

The development of charge pumps has been motivated by the power supply requirements of portable electronic devices. Charge pumps are inductorless DC-DC converters that are small size and high integration. The quality of the charge pump greatly depends on the effectiveness of switches to turn on and off at the designated clock phases. However, to date, no analysis has been carried out on the overall performance of charge pumps based on switch components in practice. This work demonstrates the characteristics of transistors as charge transfer switches and their effects on the performance of a charge pump. Three most common charge pump topologies are evaluated in terms of voltage drop due to on-resistance and charge loss per switch. Simulations are performed in 0.35μm Austriamicrosystems (AMS) technology for Dickson, Voltage Doubler and Makowski charge pump topologies in steady and dynamic states. In addition, the effect of switch parameters for different charge pump topologies are compared and analysed. We demonstrate that the Makowski charge pump is the topology for future green mobile technology

Noise shaping Asynchronous SAR ADC based time to digital converter

Time-to-digital converters (TDCs) are key elements for the digitization of timing information in modern mixed-signal circuits such as digital PLLs, DLLs, ADCs, and on-chip jitter-monitoring circuits. Especially, high-resolution TDCs are increasingly employed in on-chip timing tests, such as jitter and clock skew measurements, as advanced fabrication technologies allow fine on-chip time resolutions. Its main purpose is to quantize the time interval of a pulse signal or the time interval between the rising edges of two clock signals. Similarly to ADCs, the performance of TDCs are also primarily characterized by Resolution, Sampling Rate, FOM, SNDR, Dynamic Range and DNL/INL. This work proposes and demonstrates 2nd order noise shaping Asynchronous SAR ADC based TDC architecture with highest resolution of 0.25 ps among current state of art designs with respect to post-layout simulation results. This circuit is a combination of low power/High Resolution 2nd Order Noise Shaped Asynchronous SAR ADC backend with simple Time to Amplitude converter (TAC) front-end and is implemented in 40nm CMOS technology. Additionally, special emphasis is given on the discussion on various current state of art TDC architectures.Electrical and Computer Engineerin

Low-Power Energy Efficient Circuit Techniques for Small IoT Systems

Although the improvement in circuit speed has been limited in recent years, there has been increased focus on the internet of things (IoT) as technology scaling has decreased circuit size, power usage and cost. This trend has led to the development of many small sensor systems with affordable costs and diverse functions, offering people convenient connection with and control over their surroundings. This dissertation discusses the major challenges and their solutions in realizing small IoT systems, focusing on non-digital blocks, such as power converters and analog sensing blocks, which have difficulty in following the traditional scaling trends of digital circuits. To accommodate the limited energy storage and harvesting capacity of small IoT systems, this dissertation presents an energy harvester and voltage regulators with low quiescent power and good efficiency in ultra-low power ranges. Switched-capacitor-based converters with wide-range energy-efficient voltage-controlled oscillators assisted by power-efficient self-oscillating voltage doublers and new cascaded converter topologies for more conversion ratio configurability achieve efficient power conversion down to several nanowatts. To further improve the power efficiency of these systems, analog circuits essential to most wireless IoT systems are also discussed and improved. A capacitance-to-digital sensor interface and a clocked comparator design are improved by their digital-like implementation and operation in phase and frequency domain. Thanks to the removal of large passive elements and complex analog blocks, both designs achieve excellent area reduction while maintaining state-of-art energy efficiencies. Finally, a technique for removing dynamic voltage and temperature variations is presented as smaller circuits in advanced technologies are more vulnerable to these variations. A 2-D simultaneous feedback control using an on-chip oven control locks the supply voltage and temperature of a small on-chip domain and protects circuits in this locked domain from external voltage and temperature changes, demonstrating 0.0066 V/V and 0.013 °C/°C sensitivities to external changes. Simple digital implementation of the sensors and most parts of the control loops allows robust operation within wide voltage and temperature ranges.PHDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttps://deepblue.lib.umich.edu/bitstream/2027.42/138743/1/wanyeong_1.pd

Switched-capacitors as local converters for snake PV modules : a cost/efficiency exploration

In order to reduce the negative effect of partial shading and other sources of current mismatch within a module, smart reconfigurable modules allow altering the connections between groups of cells (cell-strings). With a proper algorithm managing these connections, we can make sure that the majority of the cells are operating close to their MPP, even when a part of the module is shaded. Such a smart reconfigurable module consists of some extra components. Switches are needed to change the interconnection scheme. Small, local converters collect power from multiple cell-strings. They step-up the voltage to reduce the current on the central bus they are connected to. At the end where we connect to the string-level bus, a module converter further regulates the voltage for the grid or the PV array. This topology was presented before where we showed that a smart reconfigurable module could recover up to 70% of the power lost to partial shading. In this paper we take a closer look at the local DC-DC converter. More precisely, we present a cost-efficiency analysis of different converter topologies. Taking into account practical limitations (economical limitations, number of components, maximum switch currents, maximum capacitance values, etc..) we estimate efficiency and projected cost. We show that Dickson pump (CR3) with 30-35mOhm switches is the best candidate. This would result in a chip cost of about €1.

Nd:YAG development for spaceborne laser ranging system

The results of the development of a unique modelocked laser device to be utilized in future NASA space-based, ultraprecision laser ranger systems are summarized. The engineering breadboard constructed proved the feasibility of the pump-pulsed, actively modelocked, PTM Q-switched Nd:YAG laser concept for the generation of subnanosecond pulses suitable for ultra-precision ranging. The laser breadboard also included a double-pass Nd:YAG amplifier and provision for a Type II KD*P frequency doubler. The specific technical accomplishment was the generation of single 150 psec, 20-mJ pulses at 10 pps at a wavelength of 1.064 micrometers with 25 dB suppression of pre-and post-pulses

Low power VCO-based analog-to-digital conversion

textThis dissertation presents novel two stage ADC architecture with a VCO based second stage. With the scaling of the supply voltages in modern CMOS process it is difficult to design high gain operational amplifiers needed for traditional voltage domain two-stage analog to digital converters. However time resolution continues to improve with the advancement in CMOS technology making VCO-based ADC more attractive. The nonlinearity in voltage-to-frequency transfer function is the biggest challenge in design of VCO based ADC. The hybrid approach used in this work uses a voltage domain first stage to determine the most significant bits and uses a VCO based second stage to quantize the small residue obtained from first stage. The architecture relaxes the gain requirement on the the first stage opamp and also relaxes the linearity requirements on the second stage VCO. The prototype ADC built in 65nm CMOS process achieves 63.7dB SNDR in 10MHz bandwidth while only consuming 1.1mW of power. The performance of the prototype chip is comparable to the state-of-art in terms of figure-of-merit but this new architecture uses significantly less circuit area.Electrical and Computer Engineerin

Circuit design techniques for Power Efficient Microscale Energy Harvesting Systems

Power Management is considered one of the hot topics nowadays, as it is already known that all integrated circuits need a stable supply with low noise, a constant voltage level across time, and the ability to supply large range of loads. Normal batteries do not provide those specifications. A new concept of energy management called energy harvesting is introduced here. Energy harvesting means collecting power from ambient resources like solar power, Radio Frequency (RF) power, energy from motion...etc. The Energy is collected by means of a transducer that directly converts this energy into electrical energy that can be managed by design to supply different loads. Harvested energy management is critical because normal batteries have to be replaced with energy harvesting modules with power management, in order to make integrated circuits fully autonomous; this leads to a decrease in maintenance costs and increases the life time. This work covers the design of an energy harvesting system focusing on micro-scale solar energy harvesting with power management. The target application of this study is a Wireless Sensor Node/Network (WSN) because its applications are very wide and power management in it is a big issue, as it is very hard to replace the battery of a WSN after deployment. The contribution of this work is mainly shown on two different scopes. The first scope is to propose a new tracking technique and to verify on the system level. The second scope is to propose a new optimized architecture for switched capacitor based power converters. At last, some future recommendations are proposed for this work to be more robust and reliable so that it can be transfered to the production phase. The proposed system design is based on the sub-threshold operation. This design approach decreases the amount of power consumed in the control circuit. It can efficiently harvest the maximum power possible from the photo-voltaic cell and transfer this power to the super-capacitor side with high efficiency. It shows a better performance compared to the literature work. The proposed architecture of the charge pump is more efficient in terms of power capability and knee frequency over the basic linear charge pump topology. Comparison with recent topologies are discussed and shows the robustness of the proposed technique

3중 샘플링 방식 델타-시그마 ADC를 이용한 디지털 Capacitive MEMS 마이크로폰

학위논문(박사) -- 서울대학교대학원 : 공과대학 전기·정보공학부, 2022. 8. 김수환.본 논문에서는 트리플 샘플링 적분기를 사용한 Capacitive 방식의 MEMS 마이크로폰이 제시되었다. 트리플 샘플링은 델타-시그마 방식의 아날로그-디지털 변환기의 첫 번째 적분기에 사용되었고 크게 두 가지의 동작으로 구분된다. 첫 번째로 적분기의 입력에서 반주기 지연 차동 입력을 빼서 신호 크기를 2배로 만들는 방식. 두 번째로 DAC의 피드백 커패시터를 샘플링 커패시터로 사용하여 입력 전압을 추가로 증가시키는 방식이다. 추가적으로 기존에서 샘플링 커패시터를 증가시켜 신호의 크기를 증폭시키는 방식과 결합하여 실수배의 이득을 얻을 수 있다. 또한 추가적인 커패시터, 타이밍, 전류 소모 없이 구조 변경만으로 이를 달성하였기 때문에 별다른 trade-off 없이 신호의 크기를 증폭시킬 수 있었다. 추가적으로 트리플 샘플링 방식의 적분기 신호 전달 함수 및 잡음 분석 또한 포함하였다. 우리의 readout 회로는 공급 전압이 1.8V인 0.18 m CMOS 공정으로 구현하였고 single-ended capacitive MEMS 트랜스듀서를 사용하여 측정하였다. 전류 소모량은 520 μA 이다. 마이크로폰은 A-weighted 신호 대 잡음 비는 62.1 dBA, 음향 과부하 지점은 115 dB SPL을 달성하였고 칩의 die size는 0.98〖"mm" 〗^2 이다.A triple-sampling ΔΣ ADC can replace the programmable-gain amplifier commonly used in the readout circuit for a digital capacitive MEMS microphone. The input voltage can then be multiplied by subtracting a further half-period delayed differential input and using the feedback capacitor of the DAC as a sampling capacitor. This triple-sampling technique results in a readout circuit with sensitivity and noise performance comparable to recent designs, but with a reduced power requirement. CMRR improvement is achieved by subtracting differential inputs and superior noise performance compare to conventional structure, as amplifier noise and DAC kT/C noise is not amplified by triple-sampling structure while the signal is increased by its gain. Triple-sampling also can be operated as a single-to-differential circuit. A MEMS microphone incorporating this readout circuit, fabricated in a 0.18μm CMOS process, achieved an A-weighted SNR of 62.1 dBA at 94 dB SPL with 520 μA current consumption, to which triple-sampling was shown to contribute 4.5 dBA.CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.1.1 MEMS MICROPHONE TRENDS 1 1.1.2 TYPE OF MEMS MICROPHONES 4 1.1.3 PREVIOUS WORKS 7 1.2 MEMS MICROPHONE BASIC TERMS 9 1.3 THESIS ORGANIZATION 12 CHAPTER 2 SYSTEM OVERVIEW 13 2.1 SYSTEM ARCHITECTURE 13 CHAPTER 3 INTERFACE CIRCUITS AND POWER MANAGEMENT CIRCUITS 16 3.1 PSEUDO-DIFFERENTIAL SOURCE FOLLOWER 17 3.2 CHARGE PUMP 19 3.3 LOW DROPOUT REGULATOR 22 3.3.1 DESIGN CONSIDERATION OF LOW DROPOUT REGULATOR 22 3.3.2 IMPLEMENTATION OF LOW DROPOUT REGULATOR 26 CHAPTER 4 TRIPLE-SAMPLING DELTA-SIGMA ADC 31 4.1 BASIC OF DELTA-SIGMA ADC 31 4.2 IMPLEMENTATION OF TRIPLE-SAMPLING DELTA-SIGMA MODULATOR 37 4.2.1 CONVENTIONAL 1ST INTEGRATOR STRUCTURE 37 4.2.2 CROSS-SAMPLING 1ST INTEGRATOR 40 4.2.3 TRIPLE-SAMPLING 1ST INTEGRATOR 43 4.2.4 STF ANALYSIS OF TRIPLE-SAMPLING 1ST INTEGRATOR 47 4.2.5 THERMAL NOISE ANALYSIS OF TRIPLE-SAMPLING 1ST INTEGRATOR 51 4.2 CIRCUIT IMPLEMENTATION OF DELTA-SIGMA ADC 57 CHAPTER 5 MEASUREMENT RESULTS 64 5.1 MEASUREMENT ENVIRONMENT 64 5.2 MEASUREMENT RESULTS 67 5.3 PERFORMANCE SUMMARY 72 CHAPTER 6 CONCLUSION 74 BIBLIOGRAPHY 76 한글초록 79박

A Charge Pump Architecture with High Power-Efficiency and Low Output Ripple Noise in 0.5 μm CMOS Process Technology

The demand of portable consumer electronic devices is skyrocketing day-by-day. Such modern integrated microsystems have several functional blocks which require different voltages to operate adequately. DC-DC converter circuits are used to generate different voltage domains for different functional blocks on large integrated microsystems from a single voltage battery-operated power supply. Charge pump is an inductorless DC-DC converter which generates higher positive voltage or lower voltage or negative voltage from the applied reference voltage. A charge pump circuit uses switches for charge transfer action and capacitors for charge storage. The thesis presents a high power-efficiency charge pump architecture with low output ripple noise in the AMI N-well 0.5 µm CMOS process technology. The switching action of the proposed charge pump architecture is controlled by a dual phase non-overlapping clock system. In order to achieve high power-efficiency, the power losses due to the leakage currents, the finite switch resistance and the imperfect charge transfer between the capacitors are taken into consideration and are minimized by proper switching of the charge transfer switches and by using different auxiliary circuits. To achieve low output ripple noise, the continuous current pumping method is proposed and implemented in the charge pump architecture. The proposed charge pump can operate over the wide input voltage range varying from 3 V to 7 V with the power conversion efficiency of 90%. The loading current drive capability of the proposed charge pump is ranging from 0 to 45 mA. The worst case output ripple voltage is less than 25 mV. To prove the concept, the design of the proposed charge pump is simulated rigorously over different process, temperature and voltage corners