Design of a tunable multi-band differential LC VCO using 0.35 mu m SiGe BiCMOS technology for multi-standard wireless communication systems

In this paper, an integrated 2.2-5.7GHz multi-band differential LC VCO for multi-standard wireless communication systems was designed utilizing 0.35 mu m SiGe BiCMOS technology. The topology, which combines the switching inductors and capacitors together in the same circuit, is a novel approach for wideband VCOs. Based on the post-layout simulation results, the VCO can be tuned using a DC voltage of 0 to 3.3 V for 5 different frequency bands (2.27-2.51 GHz, 2.48-2.78 GHz, 3.22-3.53 GHz, 3.48-3.91 GHz and 4.528-5.7 GHz) with a maximum bandwidth of 1.36 GHz and a minimum bandwidth of 300 MHz. The designed and simulated VCO can generate a differential output power between 0.992 and -6.087 dBm with an average power consumption of 44.21 mW including the buffers. The average second and third harmonics level were obtained as -37.21 and -47.6 dBm, respectively. The phase noise between -110.45 and -122.5 dBc/Hz, that was simulated at 1 MHz offset, can be obtained through the frequency of interest. Additionally, the figure of merit (FOM), that includes all important parameters such as the phase noise, the power consumption and the ratio of the operating frequency to the offset frequency, is between -176.48 and -181.16 and comparable or better than the ones with the other current VCOs. The main advantage of this study in comparison with the other VCOs, is covering 5 frequency bands starting from 2.27 up to 5.76 GHz without FOM and area abandonment. Output power of the fundamental frequency changes between -6.087 and 0.992 dBm, depending on the bias conditions (operating bands). Based on the post-layout simulation results, the core VCO circuit draws a current between 2.4-6.3 mA and between 11.4 and 15.3 mA with the buffer circuit from 3.3 V supply. The circuit occupies an area of 1.477 mm(2) on Si substrate, including DC, digital and RF pads

CMOS design of chaotic oscillators using state variables: a monolithic Chua's circuit

This paper presents design considerations for monolithic implementation of piecewise-linear (PWL) dynamic systems in CMOS technology. Starting from a review of available CMOS circuit primitives and their respective merits and drawbacks, the paper proposes a synthesis approach for PWL dynamic systems, based on state-variable methods, and identifies the associated analog operators. The GmC approach, combining quasi-linear VCCS's, PWL VCCS's, and capacitors is then explored regarding the implementation of these operators. CMOS basic building blocks for the realization of the quasi-linear VCCS's and PWL VCCS's are presented and applied to design a Chua's circuit IC. The influence of GmC parasitics on the performance of dynamic PWL systems is illustrated through this example. Measured chaotic attractors from a Chua's circuit prototype are given. The prototype has been fabricated in a 2.4- mu m double-poly n-well CMOS technology, and occupies 0.35 mm/sup 2/, with a power consumption of 1.6 mW for a +or-2.5-V symmetric supply. Measurements show bifurcation toward a double-scroll Chua's attractor by changing a bias current

Low power low voltage quadrature RC oscillators for modern RF receivers

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para a obtenção do grau de Mestre em Engenharia Electrotécnica e de ComputadoresThis thesis proposes a study of three different RC oscillators, two relaxation and a ring oscillator. All the circuits are implemented using UMC 130 nm CMOS technology with a supply voltage of 1.2 V. We present a wideband MOS current/voltage controlled quadrature oscillator constituted by two multivibrators. Two different forms of coupling named, soft (traditional)and hard (proposed) are differentiated and investigated. It is found that hard coupling reduces the quadrature error and results in a low phase-noise (about 2 dB improvement) with respect to soft coupling. The behaviour of the singular and coupled multivibrators is investigated, when an external synchronizing harmonic is applied. We introduce a new RC relaxation oscillator with pulse self biasing, to reduce power consumption, and with harmonic ltering and resistor feedback, to reduce phase-noise. The designed circuit has a very low phase-noise, -132.6 dBc/Hz @ 10 MHz offset, and the power consumption is only 1 mW, which leads to a gure of merit (FOM) of -159.1 dBc/Hz. The nal circuit is a two integrator fully implemented in CMOS technology, with low power consumption. The respective layout is made and occupies a total area of5.856x10-3 mm2, post-layout simulation is also done

High Frequency, High Linearity and Low Noise Digital to Time Converter for Phase Adjustment

Nowadays, fast communication systems have become vital for our lifestyle. As a result, the digital PLL fulfils a very important role as frequency synthesizer, demodulator or distributor of clock signals in microprocessors and similar digital circuits. Thus, the correction of the signal using a phase adjust- ment is essential for the good operation of the PLL. In this work, it is proposed a variable slope digital to time converter (DTC), as a programmable delay line, used for the correction of the phase of a digital PLL. The work is focused on the study of the performance of the circuit, through the evaluation of fundamental parameters such as RMS jitter, line- arity, resolution and delay range. Accordingly, it is employed a 4-bit topology using 130 nm MOSFET technology. The in- tended DTC takes advantage of CMOS inverters, due to their simplicity and low noise, and capacitors, for the programmable delay RC network. The DTC functioning is based on the activation of switching transistors to trigger the programmable capacitors, through a code to define the number of capacitors that introduce delay. The circuit is complemented with a simple CMOS inverter as a comparator that triggers when the threshold voltage is attained and an output buffer employed to correct the slopes of the signal. The proposed DTC proposed is a single-ended architecture that achieves 52.50 fs RMS jitter, and the resulting DNL and INL are equivalent to 0.1124 LSB and 0.09773 LSB, respectively. The 4-bit de- lay line has a resolution of 15.2 ps, an area of 0.018 mm2 and a power consumption of 62.8 μW from a 1.2 V low dropout regulator (LDO).Atualmente, os sistemas de comunicação rápida tornaram-se vitais para o nosso estilo de vida. Como resultado, a PLL digital apresenta um papel importante em funções como sintetizador de frequên- cia, demodulador ou distribuidor de sinais de relógio de microprocessadores ou circuitos digitais seme- lhantes. Assim, a correção do sinal utilizando um ajuste de fase é essencial para o bom funcionamento da PLL. Neste trabalho, é proposto um conversor digital para tempo de inclinação de curva variável, como uma linha de atraso programável, utilizada para corrigir a fase de uma PLL digital. Este trabalho é focado no estudo da performance do dispositivo, através da avaliação de parâme- tros fundamentais como RMS jitter, linearidade, resolução e range de atraso. Desta forma, a topologia implementada utiliza 4 bits e tecnologia MOSFET 130 . O conversor digital para tempo é criado utilizando inversores CMOS, que têm as vantagens de apresentar simplicidade e baixo ruído, e condensadores, utilizados para programar a rede de atraso de RC. Este funciona com base na ativação de transístores, empregues como interruptores para acionar os conden- sadores programáveis, através de um código que define o número de condensadores ligados que intro- duzem atraso. O circuito é complementado com um inversor CMOS como comparador que é acionado quando a voltagem de threshold é atingida e um buffer de saída implementado para corrigir a inclinação das curvas. O respetivo conversor apresenta uma arquitetura com uma única saída que é capaz de atingir 52.50 fs RMS jitter, e possuí DNL e INL equivalente a 0.1124 LSB e 0.09773 LSB, respetivamente. A linha de atraso de 4 bits tem uma resolução de 15.2 ps, uma área de 0.018 mm2 e um consumo de potência de 62.8 μW vindo de um regulador de baixa queda de tensão de 1.2 V

Realization of a voltage controlled oscillator using 0.35 um sige-bicmos technology for multi-band applications

The stable growth in wireless communications market has engendered the interoperability of various standards in a single broadband frequency range from hundred MHz up to several GHz. This frequency range consists of various wireless applications such as GSM, Bluetooth and WLAN. Therefore, an agile wireless system needs smart RF front-ends for functioning properly in such a crowded spectrum. As a result, the demand for multi-standard RF transceivers which put various wireless and cordless phone standards together in one structure was increased. The demand for multi-standard RF transceivers gives a key role to reconfigurable wideband VCO operation with low-power and low-phase noise characteristics. Besides agility and intelligence, such a communication system (GSM, WLAN, Global Positioning Systems, etc. ) required meeting the requirements of several standards in a cost-effective way. This, when cost and integration are the major concerns, leads to the exploitation of Si-based technologies. In this thesis, an integrated 2.2-5.7GHz Multi-band differential LC VCO for Multi-standard Wireless Communication systems was designed utilizing 0.35μm SiGe BiCMOS technology. The topology, which combines the switching inductors and capacitors together in the same circuit, is a novel approach for wideband VCOs. Based on the post layout simulation results, the VCO can be tuned using a DC voltage of 0 to 3.3V for 5 different frequency bands (2.27-2.51 GHz, 2.48-2.78GHz, 3.22-3.53GHz, 3.48-3.91GHz and 4.528-5.7GHz) with a maximum bandwidth of 1.36GHz and a minimum bandwidth of 300MHz. The designed and simulated VCO can generate a differential output power between 0.992 dBm and -6.087 dBm with an average power consumption of 44.21mW including the buffers. The average second and third harmonics level were obtained as -37.21 dBm and -47.6 dBm, respectively. The phase noise between -110.45 and -122.5 dBc/Hz, that was simulated at 1 MHz offset, can be obtained through the frequency of interest. Additionally, the figure of merit (FOM), that includes all important parameters such as the phase noise, the power consumption and the ratio of the operating frequency to the offset frequency, is between -176.48 and -181.16 and comparable or better than the ones with the other current VCOs. The main advantage of this study in comparison with the other VCOs, is covering 5 frequency bands starting from 2.27 up to 5.76 GHz without FOM and area abandonment

Design Of A 2.4 Ghz Low Power Lc Vco In Umc 0.18u Technology

Tez (Yüksek Lisans) -- İstanbul Teknik Üniversitesi, Fen Bilimleri Enstitüsü, 2007Thesis (M.Sc.) -- İstanbul Technical University, Institute of Science and Technology, 2007Bu çalışmada, Bluetooth uygulamalarında kullanılmak üzere 2.45GHz merkez frekansında çalışan, frekans ayarlaması 2.2GHz ile 2.7GHz arasında değişen, düşük güç (2mW) tüketimi sağlayan bir LC GKO (VCO) tasarlanmıştır. Faz gürültüsünü minimize etmek maksadıyla 4 bit anahtarlamalı IMOS dizisinden yararlanılmıştır. Ayrıca frekansın ince ayarı için kapasite kuplajlı diyot varaktör devresi eklenmiştir. Bu frekans ayarlama tekniğinin faz gürültüsüne etkisi en kötü hal için 50kHz ofsette yaklaşık olarak 2dBc/Hz olup yüksek ofsetlerde yok denecek kadar azdır. Devrenin kaba kontrol gerilimleri 1.4V ve 0V olup, ince ayar gerilimi ise 0.5V ile 1.4V arasındadır. Besleme geriliminin 1.4V olduğu dikkate alındığında devre yüksek entegrasyon olanağı sunmaktadır. Faz gürültüsü 50kHz ofsette -88.6dBc/Hz ile -94.36dBc/Hz arasında olup 3MHz ofsette ise -128.3dBc/Hz ile -130.5dBc/Hz değerlerine ulaşmaktadır.Bu devreye ek olarak daha düşük gerilimli farklı topolojiler aynı akım akıtacak şekilde tasarlanmış ve tezin aynı zamanda ISM bandında çalışan düşük güç sarfiyatı isteyen uygulamalarda gerekli olacak bir GKO ihtiyacı için karşılaştırmalı bir çalışma olması sağlanmıştır.In this study, a low power LC VCO which operates at a center frequency of 2.45GHz over the range between 2.2GHz and 2.7GHz is designed for Bluetooth applications. The oscillator consumes 2mW at a supply voltage of 1.4V. To minimize the phase noise generated by the varactor through AM-PM conversion, 4bits SCA varactor is implemented by employing IMOS varactors. For fine tuning of frequency, a capacitor coupled diode varactor structure is designed. The effect of this overall varactor structure on the phase noise is around 2dBc/Hz at 50kHz offset for the worst case whereas it is negligble at high offsets. The coarse control tuning voltage values are 0V and 1.4V and the fine tuning control voltage varies from 0.5V to 1.4V. Hence, a high integration is achieved by keeping the external voltage at power supply voltage. The phase noise is between -88.6dBc/Hz and -94.36dBc/Hz at 50kHz offset, and between -128.3dBc/Hz and -130.5dBc/Hz at 3MHz offset. In addition to this, several circuits enabling lower supply voltage are simulated by keeping the same current in order to constitute a comparative study for low power applications which do not require stringent phase noise specification at 2.4GHz.Yüksek LisansM.Sc

Reconfigurable time interval measurement circuit incorporating a programmable gain time difference amplifier

PhD ThesisAs further advances are made in semiconductor manufacturing technology the performance of circuits is continuously increasing. Unfortunately, as the technology node descends deeper into the nanometre region, achieving the potential performance gain is becoming more of a challenge; due not only to the effects of process variation but also to the reduced timing margins between signals within the circuit creating timing problems. Production Standard Automatic Test Equipment (ATE) is incapable of performing internal timing measurements due, first to the lack of accessibility and second to the overall timing accuracy of the tester which is grossly inadequate. To address these issue ‘on-chip’ time measurement circuits have been developed in a similar way that built in self-test (BIST) evolved for ‘on-chip’ logic testing. This thesis describes the design and analysis of three time amplifier circuits. The analysis undertaken considers the operational aspects related to gain and input dynamic range, together with the robustness of the circuits to the effects of process, voltage and temperature (PVT) variations. The design which had the best overall performance was subsequently compared to a benchmark design, which used the ‘buffer delay offset’ technique for time amplification, and showed a marked 6.5 times improvement on the dynamic range extending this from 40 ps to 300ps. The new design was also more robust to the effects of PVT variations. The new time amplifier design was further developed to include an adjustable gain capability which could be varied in steps of approximately 7.5 from 4 to 117. The time amplifier was then connected to a 32-stage tapped delay line to create a reconfigurable time measurement circuit with an adjustable resolution range from 15 down to 0.5 ps and a dynamic range from 480 down to 16 ps depending upon the gain setting. The overall footprint of the measurement circuit, together with its calibration module occupies an area of 0.026 mm2 The final circuit, overall, satisfied the main design criteria for ‘on-chip’ time measurement circuitry, namely, it has a wide dynamic range, high resolution, robust to the effects of PVT and has a small area overhead.Umm Al-Qura University

Integrated chaos generators

This paper surveys the different design issues, from mathematical model to silicon, involved on the design of integrated circuits for the generation of chaotic behavior.Comisión Interministerial de Ciencia y Tecnología 1FD97-1611(TIC)European Commission ESPRIT 3110

Phase Noise Analyses and Measurements in the Hybrid Memristor-CMOS Phase-Locked Loop Design and Devices Beyond Bulk CMOS

Phase-locked loop (PLLs) has been widely used in analog or mixed-signal integrated circuits. Since there is an increasing market for low noise and high speed devices, PLLs are being employed in communications. In this dissertation, we investigated phase noise, tuning range, jitter, and power performances in different architectures of PLL designs. More energy efficient devices such as memristor, graphene, transition metal di-chalcogenide (TMDC) materials and their respective transistors are introduced in the design phase-locked loop. Subsequently, we modeled phase noise of a CMOS phase-locked loop from the superposition of noises from its building blocks which comprises of a voltage-controlled oscillator, loop filter, frequency divider, phase-frequency detector, and the auxiliary input reference clock. Similarly, a linear time-invariant model that has additive noise sources in frequency domain is used to analyze the phase noise. The modeled phase noise results are further compared with the corresponding phase-locked loop designs in different n-well CMOS processes. With the scaling of CMOS technology and the increase of the electrical field, the problem of short channel effects (SCE) has become dominant, which causes decay in subthreshold slope (SS) and positive and negative shifts in the threshold voltages of nMOS and pMOS transistors, respectively. Various devices are proposed to continue extending Moore\u27s law and the roadmap in semiconductor industry. We employed tunnel field effect transistor owing to its better performance in terms of SS, leakage current, power consumption etc. Applying an appropriate bias voltage to the gate-source region of TFET causes the valence band to align with the conduction band and injecting the charge carriers. Similarly, under reverse bias, the two bands are misaligned and there is no injection of carriers. We implemented graphene TFET and MoS2 in PLL design and the results show improvements in phase noise, jitter, tuning range, and frequency of operation. In addition, the power consumption is greatly reduced due to the low supply voltage of tunnel field effect transistor