Digital Signal Processing Capabilities of the Fujitsu MB8764

The Fujitsu MB8764 digital signal processing chip is designed to operate with a machine cycle of up to 10 MHz. The chip’s ability to perform a 16-by-16 bit multiply and add operation in one machine cycle makes it a good candidate for real time digital signal processing. Unlike the Intel 2920 the Fujitsu MB8764 does not have an onboard analog-to-digital, digital-to-analog converter. Therefore, this paper will be restricted to the operation of this device with digital data input and output. The use of the MB8764 as a digital filter is analyzed. Performance limitations due to finite word length, memory size and configuration, and clock rate are considered. The MB8764 capabilities in computing fast Fourier transforms are discussed. Development of a working digital filter with the MB8764 work station is presented

Realization of Integrable Low- Voltage Companding Filters for Portable System Applications

Undoubtedly, today’s integrated electronic systems owe their remarkable performance primarily to the rapid advancements of digital technology since 1970s. The various important advantages of digital circuits are: its abstraction from the physical details of the actual circuit implementation, its comparative insensitiveness to variations in the manufacturing process, and the operating conditions besides allowing functional complexity that would not be possible using analog technology. As a result, digital circuits usually offer a more robust behaviour than their analog counterparts, though often with area, power and speed drawbacks. Due to these and other benefits, analog functionality has increasingly been replaced by digital implementations. In spite of the advantages discussed above, analog components are far from obsolete and continue to be key components of modern electronic systems. There is a definite trend toward persistent and ubiquitous use of analog electronic circuits in day-to-day life. Portable electronic gadgets, wireless communications and the widespread application of RF tags are just a few examples of contemporary developments. While all of these electronic systems are based on digital circuitry, they heavily rely on analog components as interfaces to the real world. In fact, many modern designs combine powerful digital systems and complementary analog components on a single chip for cost and reliability reasons. Unfortunately, the design of such systems-on-chip (SOC) suffers from the vastly different design styles of analog and digital components. While mature synthesis tools are readily available for digital designs, there is hardly any such support for analog designers apart from wellestablished PSPICE-like circuit simulators. Consequently, though the analog part usually occupies only a small fraction of the entire die area of an SOC, but its design often constitutes a major bottleneck within the entire development process. Integrated continuous-time active filters are the class of continuous-time or analog circuits which are used in various applications like channel selection in radios, anti-aliasing before sampling, and hearing aids etc. One of the figures of merit of a filter is the dynamic range; this is the ratio of the largest to the smallest signal that can be applied at the input of the filter while maintaining certain specified performance. The dynamic range required in the filter varies with the application and is decided by the variation in strength of the desired signal as well as that of unwanted signals that are to be rejected by the filter. It is well known that the power dissipation and the capacitor area of an integrated active filter increases in proportion to its dynamic range. This situation is incompatible with the needs of integrated systems, especially battery operated ones. In addition to this fundamental dependence of power dissipation on dynamic range, the design of integrated active filters is further complicated by the reduction of supply voltage of integrated circuits imposed by the scaling down of technologies to attain twin objective of higher speed and lower power consumption in digital circuits. The reduction in power consumption with decreasing supply voltage does not apply to analog circuits. In fact, considerable innovation is required with a reduced supply voltage even to avoid increasing power consumption for a given signal to noise ratio (S/N). These aspects pose a great hurdle to the active filter designer. A technique which has attracted the attention of circuit designers as a possible route to filters with higher dynamic range per unit power consumption is “companding”. Companding (compression-expansion) filters are a very promising subclass of continuous-time analog filters, where the input (linear) signal is initially compressed before it will be handled by the core (non-linear) system. In order to preserve the linear operation of the whole system, the non-linear signal produced by the core system is converted back to a linear output signal by employing an appropriate output stage. The required compression and expansion operations are performed by employing bipolar transistors in active region or MOS transistors in weak inversion; the systems thus derived are known as logarithmic-domain (logdomain) systems. In case MOS transistors operated in saturation region are employed, the derived structures are known as Square-root domain systems. Finally, the third class of companding filters can also be obtained by employing bipolar transistors in active region or MOS transistors in weak inversion; the derived systems are known as Sinh-domain systems. During the last several years, a significant research effort has been already carried out in the area of companding circuits. This is due to the fact that their main advantages are the capability for operation in low-voltage environment and large dynamic range originated from their companding nature, electronic tunability of the frequency characteristics, absence of resistors and the potential for operations in varied frequency regions.Thus, it is obvious that companding filters can be employed for implementing high-performance analog signal processing in diverse frequency ranges. For example, companding filters could be used for realizing subsystems in: xDSL modems, disk drive read channels, biomedical electronics, Bluetooth/ZigBee applications, phaselocked loops, FM stereo demodulator, touch-tone telephone tone decoder and crossover network used in a three-way high-fidelity loudspeaker etc. A number of design methods for companding filters and their building blocks have been introduced in the literature. Most of the proposed filter structures operate either above 1.5V or under symmetrical (1.5V) power supplies. According to data that provides information about the near future of semiconductor technology, International Technology Roadmap for Semiconductors (ITRS), in 2013, the supply voltage of digital circuits in 32 nm technology will be 0.5 V. Therefore, the trend for the implementation of analog integrated circuits is the usage of low-voltage building blocks that use a single 0.5-1.5V power supply. Therefore, the present investigation was primarily concerned with the study and design of low voltage and low power Companding filters. The work includes the study about: the building blocks required in implementing low voltage and low power Companding filters; the techniques used to realize low voltage and low power Companding filters and their various areas of application. Various novel low voltage and low power Companding filter designs have been developed and studied for their characteristics to be applied in a particular portable area of application. The developed designs include the N-th order universal Companding filter designs, which have been reported first time in the open literature. Further, an endeavor has been made to design Companding filters with orthogonal tuning of performance parameters so that the designs can be simultaneously used for various features. The salient features of each of the developed circuit are described. Electronic tunability is one of the major features of all of the designs. Use of grounded capacitors and resistorless designs in all the cases makes the designs suitable for IC technology. All the designs operate in a low-voltage and low-power environment essential for portable system applications. Unless specified otherwise, all the investigations on these designs are based on the PSPICE simulations using model parameters of the NR100N bipolar transistors and BSIM 0.35μm/TSMC 0.25μm /TSMC 0.18μm CMOS process MOS transistors. The performance of each circuit has been validated by comparing the characteristics obtained using simulation with the results present in the open literature. The proposed designs could not be realized in silicon due to non-availability of foundry facility at the place of study. An effort has already been started to realize some of the designs in silicon and check their applicability in practical circuits. At the basic level, one of the proposed Companding filter designs was implemented using the commercially available transistor array ICs (LM3046N) and was found to verify the theoretical predictions obtained from the simulation results

Low Power Filtering Techniques for Wideband and Wireless Applications

This dissertation presents design and implementation of continuous time analog filters for two specific applications: wideband analog systems such as disk drive channel and low-power wireless applications. Specific focus has been techniques that reduce the power requirements of the overall system either through improvement in architecture or efficiency of the analog building blocks. The first problem that this dissertation addresses is the implementation of wideband filters with high equalization gain. An efficient architecture that realizes equalization zeros by combining available transfer functions associated with a biquadratic cell is proposed. A 330MHz, 5th order Gm-C lowpass Butterworth filter with 24dB boost is designed using the proposed architecture. The prototype fabricated in standard 0.35um CMOS process shows -41dB of IM3 for 250mV peak to peak swing with 8.6mW/pole of power dissipation. Also, an LC prototype implemented using similar architecture is discussed in brief. It is shown that, for practical range of frequency and SNR, LC based design is more power efficient than a Gm-C one, though at the cost of much larger area. Secondly, a complementary current mirror based building block is proposed, which pushes the limits imposed by conventional transconductors on the powerefficiency of Gm-C filters. Signal processing through complementary devices provides good linearity and Gm/Id efficiency and is shown to improve power efficiency by nearly 7 times. A current-mode 4th order Butterworth filter is designed, in 0.13um UMC technology, using the proposed building. It provides 54.2dB IM3 and 55dB SNR in 1.3GHz bandwidth while consuming as low as 24mW of power. All CMOS filter realization occupies a relatively small area and is well suited for integration in deep submicron technologies. Thirdly, a 20MHz, 68dB dynamic range active RC filter is presented. This filter is designed for a ten bit continuous time sigma delta ADC architecture developed specifically for fine-line CMOS technologies. Inverter based amplification and a common mode feedback for such amplifiers are discussed. The filter consumes 5mW of power and occupies an area of 0.07 mm2

Filter Design Considerations for High Performance Continuous-Time Low-Pass Sigma-Delta ADC

Continuous-time filters are critical components in the implementation of large bandwidth, high frequency, and high resolution continuous-time (CT) sigma-delta (ΣΔ) analog-to-digital converters (ADCs). The loop filter defines the noise-transfer function (NTF) and hence the quantization noise-shaping behavior of the ΣΔ modulator, and becomes the most critical performance determining part in ΣΔ ADC. This thesis work presents the design considerations for the loop filter in low-pass CT ΣΔ ADC with 12-bits resolution in 25MHz bandwidth and low power consumption using 0.18μm CMOS technology. Continuous-time filters are more suitable than discrete-time filters due to relaxed amplifier bandwidth requirements for high frequency ΣΔ ADCs. A fifth-order low-pass filter with cut-off frequency of 25 MHz was designed to meet the dynamic range requirement of the ADC. An active RC topology was chosen for the implementation of the loop filter, which can provide high dynamic range required by the ΣΔ ADC. The design of a summing amplifier and a novel method for adjusting the group delay in the fast path provided by a secondary feedback DAC of the ΣΔ ADC are presented in detail. The ADC was fabricated using Jazz 0.18μm CMOS technology. The implementation issues of OTAs with high-linearity and low-noise performance suitable for the broadband ADC applications are also analyzed in this work. Important design equations pertaining to the linearity and noise performance of the Gm-C biquad filters are presented. A Gm-C biquad with 100MHz center frequency and quality factor 10 was designed as a prototype to confirm with the theoretical design equations. Transistor level circuit implementation of all the analog modules was completed in a standard 0.18μm CMOS process

Direct digital design of PIDF controllers with ComPlex zeros for DC-DC buck converters

This paper presents a new direct digital design method for discrete proportional integral derivative PID + filter (PIDF) controllers employed in DC-DC buck converters. The considered controller structure results in a proper transfer function which has the advantage of being directly implementable by a microcontroller algorithm. Secondly, it can be written as an Infinite Impulse Response (IIR) digital filter. Thirdly, the further degree of freedom introduced by the low pass filter of the transfer function can be used to satisfy additional specifications. A new design procedure is proposed, which consists of the conjunction of the pole-zero cancellation method with an analytical design control methodology based on inversion formulae. These two methods are employed to reduce the negative effects introduced by the complex poles in the transfer function of the buck converter while exactly satisfying steady-state specifications on the tracking error and frequency domain requirements on the phase margin and on the gain crossover frequency. The proposed approach allows the designer to assign a closed-loop bandwidth without constraints imposed by the resonance frequency of the buck converter. The response under step variation of the reference value, and the disturbance rejection capability of the proposed control technique under load variations are also evaluated in real-time implementation by using the Arduino DUE board, and compared with other methods

CMOS Hyperbolic Sine ELIN filters for low/audio frequency biomedical applications

Hyperbolic-Sine (Sinh) filters form a subclass of Externally-Linear-Internally-Non- Linear (ELIN) systems. They can handle large-signals in a low power environment under half the capacitor area required by the more popular ELIN Log-domain filters. Their inherent class-AB nature stems from the odd property of the sinh function at the heart of their companding operation. Despite this early realisation, the Sinh filtering paradigm has not attracted the interest it deserves to date probably due to its mathematical and circuit-level complexity. This Thesis presents an overview of the CMOS weak inversion Sinh filtering paradigm and explains how biomedical systems of low- to audio-frequency range could benefit from it. Its dual scope is to: consolidate the theory behind the synthesis and design of high order Sinh continuous–time filters and more importantly to confirm their micro-power consumption and 100+ dB of DR through measured results presented for the first time. Novel high order Sinh topologies are designed by means of a systematic mathematical framework introduced. They employ a recently proposed CMOS Sinh integrator comprising only p-type devices in its translinear loops. The performance of the high order topologies is evaluated both solely and in comparison with their Log domain counterparts. A 5th order Sinh Chebyshev low pass filter is compared head-to-head with a corresponding and also novel Log domain class-AB topology, confirming that Sinh filters constitute a solution of equally high DR (100+ dB) with half the capacitor area at the expense of higher complexity and power consumption. The theoretical findings are validated by means of measured results from an 8th order notch filter for 50/60Hz noise fabricated in a 0.35μm CMOS technology. Measured results confirm a DR of 102dB, a moderate SNR of ~60dB and 74μW power consumption from 2V power supply

Composite Operational Amplifiers And Their Applications In Active Networks

A new general approach is presented for extending the useful operating frequencies of; linear active networks in general, inverting integrators, finite gain amplifiers, and active filters in particular, realized using Operational Amplifiers (OA). This is achieved by replacing each OA in the active network by a Composite Operational Amplifier (CNOA), constructed using N OA\u27s. The technique of generating the CNO\u27s for any given N is proposed. The realizations, employing the CNOA\u27s generated, are examined according to a stringent performance criterion satisfying the important properties such as extended bandwidth, stability with one and two pole OA model, low sensitivity to the active and passive components and OA mismatch, wide dynamic range...etc. Several families of CNOA\u27s for N = 2, 3, and 4, satisfy the suggested performance criterion. The CNOA\u27s thus obtained are found useful in most frequently used linear active networks, namely, functional building blocks (finite gain-positive, negative and differential-amplifiers) and inverting integrators. Several applications of CNOA\u27s in active filters illustrate clearly the considerable improvements of the filters performance when composite amplifiers were used. This led to the introduction of two useful applications, a programmable filter and the use of CNOA\u27s in inductance simulations. The results of the use of CNOA\u27s in different active networks are given and shown theoretically and experimentally to compare favorably with the state of the art realizations using the same number of OA\u27s

High Performance Integrated Circuit Blocks for High-IF Wideband Receivers

Due to the demand for high‐performance radio frequency (RF) integrated circuit design in the past years, a system‐on‐chip (SoC) that enables integration of analog and digital parts on the same die has become the trend of the microelectronics industry. As a result, a major requirement of the next generation of wireless devices is to support multiple standards in the same chip‐set. This would enable a single device to support multiple peripheral applications and services. Based on the aforementioned, the traditional superheterodyne front‐end architecture is not suitable for such applications as it would require a complete receiver for each standard to be supported. A more attractive alternative is the highintermediate frequency (IF) radio architecture. In this case the signal is digitalized at an intermediate frequency such as 200MHz. As a consequence, the baseband operations, such as down‐conversion and channel filtering, become more power and area efficient in the digital domain. Such architecture releases the specifications for most of the front‐end building blocks, but the linearity and dynamic range of the ADC become the bottlenecks in this system. The requirements of large bandwidth, high frequency and enough resolution make such ADC very difficult to realize. Many ADC architectures were analyzed and Continuous‐Time Bandpass Sigma‐Delta (CT‐BP‐ΣΔ) architecture was found to be the most suitable solution in the high‐IF receiver architecture since they combine oversampling and noise shaping to get fairly high resolution in a limited bandwidth. A major issue in continuous‐time networks is the lack of accuracy due to powervoltage‐ temperature (PVT) tolerances that lead to over 20% pole variations compared to their discrete‐time counterparts. An optimally tuned BP ΣΔ ADC requires correcting for center frequency deviations, excess loop delay, and DAC coefficients. Due to these undesirable effects, a calibration algorithm is necessary to compensate for these variations in order to achieve high SNR requirements as technology shrinks. In this work, a novel linearization technique for a Wideband Low‐Noise Amplifier (LNA) targeted for a frequency range of 3‐7GHz is presented. Post‐layout simulations show NF of 6.3dB, peak S21 of 6.1dB, and peak IIP3 of 21.3dBm, respectively. The power consumption of the LNA is 5.8mA from 2V. Secondly, the design of a CMOS 6th order CT BP‐ΣΔ modulator running at 800 MHz for High‐IF conversion of 10MHz bandwidth signals at 200 MHz is presented. A novel transconductance amplifier has been developed to achieve high linearity and high dynamic range at high frequencies. A 2‐bit quantizer with offset cancellation is alsopresented. The sixth‐order modulator is implemented using 0.18 um TSMC standard analog CMOS technology. Post‐layout simulations in cadence demonstrate that the modulator achieves a SNDR of 78 dB (~13 bit) performance over a 14MHz bandwidth. The modulator’s static power consumption is 107mW from a supply power of ± 0.9V. Finally, a calibration technique for the optimization of the Noise Transfer Function CT BP ΣΔ modulators is presented. The proposed technique employs two test tones applied at the input of the quantizer to evaluate the noise transfer function of the ADC, using the capabilities of the Digital Signal Processing (DSP) platform usually available in mixed‐mode systems. Once the ADC output bit stream is captured, necessary information to generate the control signals to tune the ADC parameters for best Signal‐to‐Quantization Noise Ratio (SQNR) performance is extracted via Least‐ Mean Squared (LMS) software‐based algorithm. Since the two tones are located outside the band of interest, the proposed global calibration approach can be used online with no significant effect on the in‐band content