68 research outputs found
Experimental Evaluation and Comparison of Time-Multiplexed Multi-FPGA Routing Architectures
Emulating large complex designs require multi-FPGA systems (MFS). However, inter-FPGA communication is confronted by the challenge of lack of interconnect capacity due to limited number of FPGA input/output (I/O) pins. Serializing parallel signals onto a single trace effectively addresses the limited I/O pin obstacle. Besides the multiplexing scheme and multiplexing ratio (number of inter-FPGA signals per trace), the choice of the MFS routing architecture also affect the critical path latency. The routing architecture of an MFS is the interconnection pattern of FPGAs, fixed wires and/or programmable interconnect chips. Performance of existing MFS routing architectures is also limited by off-chip interface selection. In this dissertation we proposed novel 2D and 3D latency-optimized time-multiplexed MFS routing architectures. We used rigorous experimental approach and real sequential benchmark circuits to evaluate and compare the proposed and existing MFS routing architectures. This research provides a new insight into the encouraging effects of using off-chip optical interface and three dimensional MFS routing architectures. The vertical stacking results in shorter off-chip links improving the overall system frequency with the additional advantage of smaller footprint area. The proposed 3D architectures employed serialized interconnect between intra-plane and inter-plane FPGAs to address the pin limitation problem. Additionally, all off-chip links are replaced by optical fibers that exhibited latency improvement and resulted in faster MFS. Results indicated that exploiting third dimension provided latency and area improvements as compared to 2D MFS. We also proposed latency-optimized planar 2D MFS architectures in which electrical interconnections are replaced by optical interface in same spatial distribution. Performance evaluation and comparison showed that the proposed architectures have reduced critical path delay and system frequency improvement as compared to conventional MFS. We also experimentally evaluated and compared the system performance of three inter-FPGA communication schemes i.e. Logic Multiplexing, SERDES and MGT in conjunction with two routing architectures i.e. Completely Connected Graph (CCG) and TORUS. Experimental results showed that SERDES attained maximum frequency than the other two schemes. However, for very high multiplexing ratios, the performance of SERDES & MGT became comparable
High-speed, low cost test platform using FPGA technology
The object of this research is to develop a low-cost, adaptable testing platform for multi-GHz digital applications, with concentration on the test requirement of advanced devices. Since most advanced ATEs are very expensive, this equipment is not always available for testing cost-sensitive devices. The approach is to use recently-introduced advanced FPGAs for the core logic of the testing platform, thereby allowing for a low-cost, low power-consumption, high-performance, and adaptable test system. Furthermore to customize the testing system for specific applications, we implemented multiple extension testing modules base on this platform. With these extension modules, new functions can be added easily and the test system can be upgraded with specific features required for other testing purposes. The applications of this platform can help those digital devices to be delivered into market with shorter time, lower cost and help the development of the whole industry.Ph.D
WDM/TDM PON bidirectional networks single-fiber/wavelength RSOA-based ONUs layer 1/2 optimization
This Thesis proposes the design and the optimization of a hybrid WDM/TDM PON at the L1 (PHY) and L2 (MAC) layers, in terms of minimum deployment cost and enhanced performance for Greenfield NGPON. The particular case of RSOA-based ONUs and ODN using a single-fibre/single-wavelength is deeply analysed. In this WDM/TDM PON relevant parameters are optimized. Special attention has been given at the main noise impairment in this type of networks: the Rayleigh Backscattering effect, which cannot be prevented. To understand its behaviour and mitigate its effects, a novel mathematical model for the Rayleigh Backscattering in burst mode transmission is presented for the first time, and it has been used to optimize the WDM/TDM RSOA based PON.
Also, a cost-effective, simple design SCM WDM/TDM PON with rSOA-based ONU, was optimized and implemented. This prototype was successfully tested showing high performance, robustness, versatility and reliability. So, the system is able to give coverage up to 1280 users at 2.5 Gb/s / 1.25 Gb/s downstream/upstream, over 20 Km, and being compatible with the GPON ITU-T recommendation.
This precedent has enabled the SARDANA network to extend the design, architecture and capabilities of a WDM/TDM PON for a long reach metro-access network (100 km). A proposal for an agile Transmission Convergence sub-layer is presented as another relevant contribution of this work. It is based on the optimization of the standards GPON and XG-PON (for compatibility), but applied to a long reach metro-access TDM/WDM PON rSOA-based network with higher client count.
Finally, a proposal of physical implementation for the SARDANA layer 2 and possible configurations for SARDANA internetworking, with the metro network and core transport network, are presented
Tecnologias coerentes para redes ópticas flexíveis
Next-generation networks enable a broad range of innovative services with
the best delivery by utilizing very dense wired/wireless networks. However,
the development of future networks will require several breakthroughs in
optical networks such as high-performance optical transceivers to support a
very-high capacity optical network as well as optimization of the network
concept, ensuring a dramatic reduction of the cost per bit.
At the same time, all of the optical network segments (metro, access,
long-haul) need new technology options to support high capacity, spectral
efficiency and data-rate flexibility. Coherent detection offers an opportunity
by providing very high sensitivity and supporting high spectral efficiency.
Coherent technology can still be combined with polarization multiplexing.
Despite the increased cost and complexity, the migration to dual-polarization
coherent transceivers must be considered, as it enables to double the spectral
efficiency. These dual-polarization systems require an additional digital signal
processing (DSP) subsystem for polarization demultiplexing. This work seeks
to provide and characterize cost-effective novel coherent transceivers for
the development of new generation practical, flexible and high capacity
transceivers for optical metro-access and data center interconnects. In this
regard, different polarization demultiplexing (PolDemux) algorithms, as well
as adaptive Stokes will be considered.
Furthermore, low complexity and modulation format-agnostic DSP techniques
based on adaptive Stokes PolDemux for flexible and customizable
optical coherent systems will be proposed. On this subject, the performance
of the adaptive Stokes algorithm in an ultra-dense wavelength division multiplexing
(U-DWDM) system will be experimentally evaluated, in offline
and real-time operations over a hybrid optical-wireless link. In addition, the
efficiency of this PolDemux algorithm in a flexible optical metro link based
on Nyquist pulse shaping U-DWDM system and hybrid optical signals will be
assessed. Moreover, it is of great importance to find a transmission technology
that enables to apply the Stokes PolDemux for long-haul transmission
systems and data center interconnects. In this work, it is also proposed
a solution based on the use of digital multi-subcarrier multiplexing, which
improve the performance of long-haul optical systems, without increasing
substantially, their complexity and cost.As redes de telecomunicações futuras permitirão uma ampla gama de serviços
inovadores e com melhor desempenho. No entanto, o desenvolvimento das
futuras redes implicará vários avanços nas redes de fibra ótica, como transcetores
óticos de alto desempenho capazes de suportar ligações de muito
elevada capacidade, e a otimização da estrutura da rede, permitindo uma
redução drástica do custo por bit transportado.
Simultaneamente, todos os segmentos de rede ótica (metropolitanas, acesso
e longo alcance) necessitam de novas opções tecnológicas para suportar
uma maior capacidade, maior eficiência espetral e flexibilidade. Neste contexto,
a deteção coerente surge como uma oportunidade, fornecendo alta
sensibilidade e elevada eficiência espetral. A tecnologia de deteção coerente
pode ainda ser associada à multiplexação na polarização. Apesar de um
potencial aumento ao nível do custo e da complexidade, a migração para
transcetores coerentes de dupla polarização deve ser ponderada, pois permite
duplicar a eficiência espetral. Esses sistemas de dupla polarização requerem
um subsistema de processamento digital de sinal (DSP) adicional para desmultiplexagem
da polarização. Este trabalho procura fornecer e caracterizar
novos transcetores coerentes de baixo custo para o desenvolvimento de uma
nova geração de transcetores mais práticos, flexíveis e de elevada capacidade,
para interconexões óticas ao nível das futuras redes de acesso e metro.
Assim, serão analisados diferentes algoritmos para a desmultiplexagem da
polarização, incluindo uma abordagem adaptativa baseada no espaço de
Stokes.
Além disso, são propostas técnicas de DSP independentes do formato de
modulação e de baixa complexidade baseadas na desmultiplexagem de Stokes
adaptativa para sistemas óticos coerentes flexíveis. Neste contexto, o desempenho
do algoritmo adaptativo de desmultiplexagem na polarização
baseado no espaço de Stokes é avaliado experimentalmente num sistema
U-DWDM, tanto em análises off-line como em tempo real, considerando um
percurso ótico hibrido que combina um sistema de transmissão suportado
por fibra e outro em espaço livre. Foi ainda analisada a eficiência do algoritmo
de desmultiplexagem na polarização numa rede ótica de acesso flexível
U-DWDM com formatação de pulso do tipo Nyquist. Neste trabalho foi
ainda analisada a aplicação da técnica de desmultiplexagem na polarização
baseada no espaço de Stokes para sistemas de longo alcance. Assim, foi
proposta uma solução de aplicação baseada no uso da multiplexagem digital
de múltiplas sub-portadoras, tendo-se demonstrado uma melhoria na eficiência
do desempenho dos sistemas óticos de longo alcance, sem aumentar
significativamente a respetiva complexidade e custo.Programa Doutoral em Engenharia Eletrotécnic
A scalable packetised radio astronomy imager
Includes bibliographical referencesModern radio astronomy telescopes the world over require digital back-ends. The complexity of these systems depends on many site-specific factors, including the number of antennas, beams and frequency channels and the bandwidth to be processed. With the increasing popularity for ever larger interferometric arrays, the processing requirements for these back-ends have increased significantly. While the techniques for building these back-ends are well understood, every installation typically still takes many years to develop as the instruments use highly specialised, custom hardware in order to cope with the demanding engineering requirements. Modern technology has enabled reprogrammable FPGA-based processing boards, together with packet-based switching techniques, to perform all the digital signal processing requirements of a modern radio telescope array. The various instruments used by radio telescopes are functionally very different, but the component operations remain remarkably similar and many share core functionalities. Generic processing platforms are thus able to share signal processing libraries and can acquire different personalities to perform different functions simply by reprogramming them and rerouting the data appropriately. Furthermore, Ethernet-based packet-switched networks are highly flexible and scalable, enabling the same instrument design to be scaled to larger installations simply by adding additional processing nodes and larger network switches. The ability of a packetised network to transfer data to arbitrary processing nodes, along with these nodes' reconfigurability, allows for unrestrained partitioning of designs and resource allocation. This thesis describes the design and construction of the first working radio astronomy imaging instrument hosted on Ethernet-interconnected re- programmable FPGA hardware. I attempt to establish an optimal packetised architecture for the most popular instruments with particular attention to the core array functions of correlation and beamforming. Emphasis is placed on requirements for South Africa's MeerKAT array. A demonstration system is constructed and deployed on the KAT-7 array, MeerKAT's prototype. This research promises reduced instrument development time, lower costs, improved reliability and closer collaboration between telescope design teams
Recommended from our members
Development of Silicon Photonic Multi Chip Module Transceivers
The exponential growth of data generation–driven in part by the proliferation of applications such as high definition streaming, artificial intelligence, and the internet of things–presents an impending bottleneck for electrical interconnects to fulfill data center bandwidth demands. Links now require bandwidths in excess of multiple Tbps while operating on the order of picojoules per bit, in addition to constraints on areal bandwidth densities and pin I/O bandwidth densities. Optical communications built on a silicon photonic platform offers a potential solution to develop power efficient, high bandwidth, low attenuation, small footprint links, all while building off the mature CMOS ecosystem. The development of silicon photonic foundries supporting multi project wafer runs with associated process design kit components supports a path towards widespread commercial production by increasing production volume while reducing fabrication and development costs. While silicon photonics can always be improved in terms of performance and yield, one of the central challenges is the integration of the silicon photonic integrated circuits with the driving electronic integrated circuits and data generating compute nodes such as CPUs, FPGAs, and ASICs. The co-packaging of the photonics with the electronics is crucial for adoption of silicon photonics in datacenters, as improper integration negates all the potential benefits of silicon photonics.
The work in this dissertation is centered around the development of silicon photonic multi chip module transceivers to aid in the deployment of silicon photonics within data centers. Section one focuses on silicon photonic integration and highlights multiple integrated transceiver prototypes. The central prototype features a photonic integrated circuit with bus waveguides with WDM microdisk modulators for the transmitter and WDM demuxes with drop ports to photodiodes for the receiver. The 2.5D integrated prototype utilizes a thinned silicon interposer and TIA electronic integrated circuits. The architecture, integration, characterization, performance, and scalability of the prototype are discussed. The development of this first prototype identified key design considerations necessary for designing multi chip module silicon photonic prototypes, which will be addressed in this section. Finally, other multi chip module silicon photonic prototypes will be overviewed. These include a 2.5D integrated transceiver with a different electronic integrated circuit TIA, a 3D integrated receiver, an active interposer network on chip, and a 2.5D integrated transceiver with custom electronic integrated circuits. Section two focuses on research that supports the development of silicon photonic transceivers. The thermal crosstalk from neighboring microdisk modulators as a function of modulator pitch is investigated. As modulators are placed at denser pitches to accommodate areal bandwidth density requirements in transceivers, this thermal crosstalk will become significant. In this section, designs and results from several iterations of custom microring modulators are reported. Custom microring modulators allow for scaling up the number of channels in microring transceivers by offering the ability to fabricate variable resonances and provide a platform for further innovation in bandwidth, free spectral range, and energy efficiency. The designs and results of higher order modulation format modulators, both microring based and Mach Zehnder based, are discussed. High order modulators offer a path towards scaling transceiver total throughput without having to increase the channel counts or component bandwidth. Together, the work in these two sections supports the development of silicon photonic transceivers to aid in the adoption of silicon photonics into data generating systems
Recommended from our members
Physical Layer Modeling and Optimization of Silicon Photonic Interconnection Networks
The progressive blooming of silicon photonics technology (SiP) has indicated that optical interconnects may substitute the electrical wires for data movement over short distances in the future. Silicon Photonics platform has been the subject of intensive research for more than a decade now and its prospects continue to emerge as it enjoys the maturity of CMOS manufacturing industry. SiP foundries all over the world and particularly in the US (AIM Photonics) have been developing reliable photonic design kits (PDKs) that include fundamental SiP building blocks such as wavelength selective modulators and tunable filters. Microring resonators (MRR) are hailed as the most compact devices that can perform both modulation and demodulation in a wavelength division multiplexed (WDM) transceiver design. Although the use of WDM can reduce the number of fibers carrying data, it also makes the design of transceivers challenging. It is probably acceptable to achieve compactness at the expense of somewhat higher transceiver cost and power consumption. Nevertheless, these two metrics should remain close to their roadmap values for Datacom applications. An increase of an order of magnitude is clearly not acceptable. For example costs relative to bandwidth for an optical link in a data center interconnect will have to decrease from the current 1/Gbps. Additionally, the transceiver itself must remain compact.
The optical properties of SiP devices are subject to various design considerations, operation conditions, and optimization procedures. In this thesis, the general goal is to develop mathematical models that can accurately describe the thermo-optical and electro-optical behavior of individual SiP devices and then use these models to perform optimization on the parameters of such devices to maximize the capabilities of photonic links or photonic switch fabrics for datacom applications.
In Chapter 1, Introduction, we first provide an overview of the current state of the optical transceivers for data centers and datacom applications. Four main categories for optical interfaces (Pluggable transceivers, On-board optics, Co-packaged optics, monolithic integration) are briefly discussed. The structure of a silicon photonic link is also briefly introduced. Then the direction is shifted towards optical switching technologies where various technologies such as free space MEMS, liquid crystal on silicon (LCOS), SOA-based switches, and silicon-based switches are explored.
In Chapter 2, Silicon Photonic Waveguides, we present an extensive study of the silicon-on-insulator (SOI) waveguides that are the basic building blocks of all of the SiP devices. The dispersion of Si and SiO2 is modeled with Sellmiere equation for the wavelength range 1500–1600 nm and then is used to calculate the TE and TM modes of a 2D slab waveguide. There are two reasons that 2D waveguides are studied: first, the modes of these waveguides have closed form solutions and the modes of 3D waveguides can be approximated from 2D waveguides based on the effective index method. Second, when the coupling of waveguides is studied and the concept of curvature function of coupling is developed, the coupled modes of 2D waveguides are used to show that this approach has some inherent small error due to the discretization of the nonuniform coupling. This chapter finishes by describing the coefficients of the sensitivity of optical modes of the waveguides to the geometrical and material parameters. Perturbation theory is briefly presented as a way to analytically examine the impact of small perturbations on the effective index of the modes.
In Chapter 3, Compact Modeling Approach, the concept of scattering matrix of a multi-port silicon photonic device is presented. The elements of the S-matrix are complex numbers that relate the amplitude and phase relationships of the optical models in the input and output ports. Based on the scattering matrix modeling of silicon photonics devices, two methods of solving photonic circuits are developed: the first one is based on the iteration for linear circuits. The second approach is based on the construction of an equivalent signal flow graph (SFG) for the circuit. We show that the SFG approach is very efficient for circuits involving microring resonator structures. Not only SFG can provide the solution for the transmission, it also provides the signal paths and the closed-form solution based on the Mason’s graph formula. We also show how the SFG method can be utilized to formulate the backscattering effects inside a ring resonator.
In Chapter 4, Scalability of Silicon Photonic Switch Fabrics, we develop the models for electro-optic Mach-Zehnder switch elements (2×2). For the electro-optic properties, the empirical Soref’s equations are used to characterize how the loss and index of silicon changes when the charge carrier density is changed. We then use our photonic circuit solver based on the iteration method to find accurate result of light propagation in large-scale switch topologies (e.g. 4×4, and 8×8). The concept of advanced path mapping based on physical layer evaluation of the switch fabric is introduced and used to develop the optimum routing tables for 4×4 and 8×8 Benes switch topologies.
In Chapter 5, Design space of Microring Resonators, we introduce the concept of curvature function of coupling to mathematically characterize the coupling coefficient of a ring resonator to a waveguide as a function of the geometrical parameters (ring radius, coupling gap, width and height of waveguides) and the wavelength. Extensive 2D and 3D FDTD simulations are carried out to validate our modeling approach. Experimental demonstrations are also used to not only further validate our modeling of coupling, but also to extract an empirical power-law model for the bending loss of the ring resonators as a function the radius. By combining these models, we for the first time present a full characterization of the design space of microring resonators. Moreover, the value of this discussion will be further apparent when the scalability of a silicon photonic link is studied. We will show that the FSR of the rings determines the optical bandwidth but it also impacts the properties of the ring resonators.
In Chapter 6, Thermo-optic Efficiency of Microheaters, we develop analytical models for the thermo-optic properties of SiP waveguides. For the thermo-optic properties, the concept of thermal impulse response is mathematically developed for integrated micro-heaters. The thermal impulse response is a key function that determines the tradeoff between heating efficiency and heating speed (thermal bandwidth), as well as allows us to predict the pulse-width-modulation (PWM) optical response of the heater-waveguide system. One of the motivations behind this study was to find the highest possible efficiency for thermal tuning of microring resonators to use it in the evaluation of the energy consumption of a photonic link. The results indicate 2 nm/mW which is in agreement with the trends that we see in the literature.
In Chapter 7, Crosstalk Penalty, we theoretically and experimentally investigate the optical crosstalk effects in microring-based silicon photonic interconnects. Both inter-channel crosstalk and intra-channel crosstalk are investigated and approximate equations are developed for their corresponding power penalties. Inclusion of the inter-channel crosstalk is an important part of our final analysis of a silicon photonic link.
In Chapter 8, Scalability of Silicon Photonic Links, we present the analysis of a WDM silicon photonics point-to-point link based on microring modulators and microring wavelength filters. Our approach is based on the power penalty analysis of non-return-to-zero (NRZ) signals and Gaussian noise statistics. All the necessary equations for the optical power penalty calculations are presented for microring modulators and filters. The first part of the analysis is based on various ideal assumptions which lead to a maximum capacity of 2.1 Tb/s for the link. The second part of the analysis is carried out with more realistic assumptions on the photonic elements in the link, culminating in a maximum throughput of 800 Gb/s. We also provide estimations of the energy/bit metric of such links based on the optimized models of electronic circuits in 65 nm CMOS technology
Adaptive modulation techniques for passive optical networks
Smart use of fiber networks to increase capacity to the hom
- …