Design of a wideband low-power continuous-time sigma-delta (ΣΔ) analog-to-digital converter (ADC) in 90nm CMOS technology

The growing trend in VLSI systems is to shift more signal processing functionality from analog to digital domain to reduce manufacturing cost and improve reliability. It has resulted in the demand for wideband high-resolution analog-to-digital converters (ADCs). There are many different techniques for doing analog-to-digital conversions. Oversampling ADC based on sigma-delta (ΣΔ) modulation is receiving a lot of attention due to its significantly relaxed matching requirements on analog components. Moreover, it does not need a steep roll-off anti-aliasing filter. A ΣΔ ADC can be implemented either as a discrete time system or a continuous time one. Nowadays growing interest is focused on the continuous-time ΣΔ ADC for its use in the wideband and low-power applications, such as medical imaging, portable ultrasound systems, wireless receivers, and test equipments. A continuous-time ΣΔ ADC offers some important advantages over its discrete-time counterpart, including higher sampling frequency, intrinsic anti-alias filtering, much relaxed sampling network requirements, and low-voltage implementation. Especially it has the potential in achieving low power consumption. This dissertation presents a novel fifth-order continuous-time ΣΔ ADC which is implemented in a 90nm CMOS technology with single 1.0-V power supply. To speed up design process, an improved direct design method is proposed and used to design the loop filter transfer function. To maximize the in-band gain provided by the loop filter, thus maximizing in-band noise suppression, the excess loop delay must be kept minimum. In this design, a very low latency 4-bit flash quantizer with digital-to-analog (DAC) trimming is utilized. DAC trimming technique is used to correct the quantizer offset error, which allows minimum-sized transistors to be used for fast and low-power operation. The modulator has sampling clock of 800MHz. It achieves a dynamic range (DR) of 75dB and a signal-to-noise-and-distortion ratio (SNDR) of 70dB over 25MHz input signal bandwidth with 16.4mW power dissipation. Our work is among the most improved published to date. It uses the lowest supply voltage and has the highest input signal bandwidth while dissipating the lowest power among the bandwidths exceeding 15MHz

High-Bandwidth Voltage-Controlled Oscillator based architectures for Analog-to-Digital Conversion

The purpose of this thesis is the proposal and implementation of data conversion open-loop architectures based on voltage-controlled oscillators (VCOs) built with ring oscillators (RO-based ADCs), suitable for highly digital designs, scalable to the newest complementary metal-oxide-semiconductor (CMOS) nodes. The scaling of the design technologies into the nanometer range imposes the reduction of the supply voltage towards small and power-efficient architectures, leading to lower voltage overhead of the transistors. Additionally, phenomena like a lower intrinsic gain, inherent noise, and parasitic effects (mismatch between devices and PVT variations) make the design of classic structures for ADCs more challenging. In recent years, time-encoded A/D conversion has gained relevant popularity due to the possibility of being implemented with mostly digital structures. Within this trend, VCOs designed with ring oscillator based topologies have emerged as promising candidates for the conception of new digitization techniques. RO-based data converters show excellent scalability and sensitivity, apart from some other desirable properties, such as inherent quantization noise shaping and implicit anti-aliasing filtering. However, their nonlinearity and the limited time delay achievable in a simple NOT gate drastically limits the resolution of the converter, especially if we focus on wide-band A/D conversion. This thesis proposes new ways to alleviate these issues. Firstly, circuit-based techniques to compensate for the nonlinearity of the ring oscillator are proposed and compared to equivalent state-of-the-art solutions. The proposals are designed and simulated in a 65-nm CMOS node for open-loop RO-based ADC architectures. One of the techniques is also validated experimentally through a prototype. Secondly, new ways to artificially increase the effective oscillation frequency are introduced and validated by simulations. Finally, new approaches to shape the quantization noise and filter the output spectrum of a RO-based ADC are proposed theoretically. In particular, a quadrature RO-based band-pass ADC and a power-efficient Nyquist A/D converter are proposed and validated by simulations. All the techniques proposed in this work are especially devoted for highbandwidth applications, such as Internet-of-Things (IoT) nodes or maximally digital radio receivers. Nevertheless, their field of application is not restricted to them, and could be extended to others like biomedical instrumentation or sensing.El propósito de esta tesis doctoral es la propuesta y la implementación de arquitecturas de conversión de datos basadas en osciladores en anillos, compatibles con diseños mayoritariamente digitales, escalables en los procesos CMOS de fabricación más modernos donde las estructuras digitales se ven favorecidas. La miniaturización de las tecnologías CMOS de diseño lleva consigo la reducción de la tensión de alimentación para el desarrollo de arquitecturas pequeñas y eficientes en potencia. Esto reduce significativamente la disponibilidad de tensión para saturar transistores, lo que añadido a una ganancia cada vez menor de los mismos, ruido y efectos parásitos como el “mismatch” y las variaciones de proceso, tensión y temperatura han llevado a que sea cada vez más complejo el diseño de estructuras analógicas eficientes. Durante los últimos años la conversión A/D basada en codificación temporal ha ganado gran popularidad dado que permite la implementación de estructuras mayoritariamente digitales. Como parte de esta evolución, los osciladores controlados por tensión diseñados con topologías de oscilador en anillo han surgido como un candidato prometedor para la concepción de nuevas técnicas de digitalización. Los convertidores de datos basados en osciladores en anillo son extremadamente sensibles (variación de frecuencia con respecto a la señal de entrada) así como escalables, además de otras propiedades muy atractivas, como el conformado espectral de ruido de cuantificación y el filtrado “anti-aliasing”. Sin embargo, su respuesta no lineal y el limitado tiempo de retraso alcanzable por una compuerta NOT restringen la resolución del conversor, especialmente para conversión A/D en aplicaciones de elevado ancho de banda. Esta tesis doctoral propone nuevas técnicas para aliviar este tipo de problemas. En primer lugar, se proponen técnicas basadas en circuito para compensar el efecto de la no linealidad en los osciladores en anillo, y se comparan con soluciones equivalentes ya publicadas. Las propuestas se diseñan y simulan en tecnología CMOS de 65 nm para arquitecturas en lazo abierto. Una de estas técnicas presentadas es también validada experimentalmente a través de un prototipo. En segundo lugar, se introducen y validan por simulación varias formas de incrementar artificialmente la frecuencia de oscilación efectiva. Para finalizar, se proponen teóricamente dos enfoques para configurar nuevas formas de conformación del ruido de cuantificación y filtrado del espectro de salida de los datos digitales. En particular, son propuestos y validados por simulación un ADC pasobanda en cuadratura de fase y un ADC de Nyquist de gran eficiencia en potencia. Todas las técnicas propuestas en este trabajo están destinadas especialmente para aplicaciones de alto ancho de banda, tales como módulos para el Internet de las cosas o receptores de radiofrecuencia mayoritariamente digitales. A pesar de ello, son extrapolables también a otros campos como el de la instrumentación biomédica o el de la medición de señales mediante sensores.Programa de Doctorado en Ingeniería Eléctrica, Electrónica y Automática por la Universidad Carlos III de MadridPresidente: Juan Pablo Alegre Pérez.- Secretario: Celia López Ongil.- Vocal: Fernando Cardes Garcí

Design techniques for sigma-delta modulators in communications applications

Specialised design techniques for sigma-delta modulators are described in this thesis with all of the examples coming from modern communications systems. The noise shaping and the signal transfer functions can be optimised using a weighted least squares approach. Numerical problems arising in the optimisation as a result of high oversampling rates are overcome through the use a simple transformation. The application to digitising audio is discussed, with the conclusion that Butterworth response noise shaping is preferable to inverse Chebyshev noise shaping for audio applications. An example of optimising the signal transfer function to provide immunity to instability brought about by large out-of-band signals is also presented. The use of redundant arithmetic in the implementation of very high speed sigma-delta modulators is introduced, together with a DAC / filter combination suitable for reconstructing an analogue signal from the redundant arithmetic SDM. An improved topology for a speech compander is described which offers a number of significant advantages over existing published methods. This uses no external components for ac coupling or setting the response time-constant, yet is robust and insensitive to parasitic components and process variations. This has been integrated on a CMOS IC process and the results are compared with the high level simulations. A simulation method which allows the verification of switched-capacitor schematics with several orders of magnitude speed improvements over commercially available simulation tools is discussed. The method assumes ideal components, with internally controllable switches and reduces the schematic netlist to the few key equations that an experienced designer would derive manually. This process is fully automated and consequently is useful for providing confidence in implementations of complex SC systems

A 23μW Solar-Powered Keyword-Spotting ASIC with Ring-Oscillator-Based Time-Domain Feature Extraction

Voice-controlled interfaces on acoustic Internet-of-Things (IoT) sensor nodes and mobile devices require integrated low-power always-on wake-up functions such as Voice Activity Detection (VAD) and Keyword Spotting (KWS) to ensure longer battery life. Most VAD and KWS ICs focused on reducing the power of the feature extractor (FEx) as it is the most power-hungry building block. A serial Fast Fourier Transform (FFT)-based KWS chip [1] achieved 510nW; however, it suffered from a high 64ms latency and was limited to detection of only 1-to-4 keywords (2-to-5 classes). Although the analog FEx [2]–[3] for VAD/KWS reported 0.2μW-to-1 μW and 10ms-to-100ms latency, neither demonstrated >5 classes in keyword detection. In addition, their voltage-domain implementations cannot benefit from process scaling because the low supply voltage reduces signal swing; and the degradation of intrinsic gain forces transistors to have larger lengths and poor linearity

An Evaluation of the S2Ia switched-current architecture for (delta)(sigma) modulator ADCs

Switched-Current (SI) is a design methodology by which discrete time, current mode, analog circuits can be implemented using standard digital CMOS processes, allowing the addition of analog signal processing circuits, analog to digital converters (ADCs), digital to analog converters (DACs) and other analog and mixed-signal circuits to otherwise digital only microchips without the need and expense of any extra fabrication steps. SI circuits operate by employing a secondary effect in CMOS circuits, a transistor\u27s gate capacitance, to store charge and thus form a current memory cell. A current memory cell is one of the basic building blocks found in most SI circuits and is usually the distinguishing feature of the various approaches to SI circuit design. Delta Sigma Modulators (DSMs) are discrete time, mixed-signal circuits making them well suited to implementation using the SI methodology. These circuits can form the basis of either an ADC or DAC and thus provide a good example of the SI technique employing a particular current memory cell implementation. For this work, a First Order DSM-based ADC was designed and simulated to verify the feasibility of a variant of the S2I Switched-Current Memory Cell architecture, the S2Ia Switched-Current Memory Cell, in a low-voltage, digital, 0.5/j.m CMOS process. The A D C design was targeted towards voiceband (4kHz bandwidth) applications over which it achieved a 6-bit resolution and separately attained a greater than 80kHz bandwidth. Extension of the First Order DSM employed in this design to a Second Order DSM would increase the resolution to at least 8-bits without sacrificing bandwidth. Although potentially less accurate than the S2I Switched-Current Memory Cell, a S2Ia cell has the advantage of requiring only two clock signals to the S2I cell\u27s four. Further, for cascades of S2Ia cells the number of clock signals remains two while a S2I cell cascade requires six separate clock signals. S2Ia-based circuits therefore require less complex clock generation circuitry and fewer clock lines

Design and FPGA implementation of a SISO and a MIMO wireless system for software defined radio

MIMO (Multiple-input Multiple-output) technology combined with space time coding techniques provides significant increase in performance and capacity over an equivalent SISO (Single-input Single-output) system while maintaining the same bandwidth and transmission power. MIMO has emerged as the major breakthrough in recent communication technologies. To migrate from SISO to MIMO system, multiple RF (Radio Frequency) front ends and additional signal processing are required. Software defined radio (SDR) allows MIMO and other evolving techniques to be added to current systems through software update instead of hardware replacement. SDR provides a flexible and economic solution to the system upgrade and migration. In this thesis, an SDR based SISO system using QPSK modulation scheme is implemented on FPGA. The system produces signal with an intermediate frequency of 25 MHz and throughput of 12.5 Mbps. One carrier recovery and two symbol timing recovery algorithms (Gardner and Maximum Likelihood) are investigated and implemented. A 2x1 MIMO system using Alamouti scheme and CORDIC based carrier recovery is designed as well. The SDR based SISO system can be easily incorporated to the MIMO design. Throughout this thesis, detailed design information is presented along with both computer simulation results and real hardware performance. The comparisons of different algorithms and component structures are also provided. Based on these comparisons, the suitable algorithm or structure according to specific implementation considerations and system requirement can be selected. The design and implementation are processed based on a system-level design flow. System modeling and simulation are performed using Xilinx's System Generator for DSP and Simulink. After it is mapped to HDL (Hardware Description Language) netlist, the design is synthesized and implemented by Xilinx's ISE tool. The generated bit-stream is then downloaded to target FPGA to program the device. The hardware performance is measured by BER (Bit Error Rate) tester, oscilloscope and spectrum analyzer. This thesis is an initial project for future work of Wireless Design Laboratory at Concordia University. The system realized in this project can be viewed as a base of future MIMO implementation with different number of antennas and advanced signal processing techniques

Time-encoding analog-to-digital converters : bridging the analog gap to advanced digital CMOS? Part 2: architectures and circuits

The scaling of CMOS technology deep into the nanometer range has created challenges for the design of highperformance analog ICs: they remain large in area and power consumption in spite of process scaling. Analog circuits based on time encoding [1], [2], where the signal information is encoded in the waveform transitions instead of its amplitude, have been developed to overcome these issues. While part one of this overview article [3] presented the basic principles of time encoding, this follow-up article describes and compares the main time-encoding architectures for analog-to-digital converters (ADCs) and discusses the corresponding design challenges of the circuit blocks. The focus is on structures that avoid, as much as possible, the use of traditional analog blocks like operational amplifiers (opamps) or comparators but instead use digital circuitry, ring oscillators, flip-flops, counters, an so on. Our overview of the state of the art will show that these circuits can achieve excellent performance. The obvious benefit of this highly digital approach to realizing analog functionality is that the resulting circuits are small in area and more compatible with CMOS process scaling. The approach also allows for the easy integration of these analog functions in systems on chip operating at "digital" supply voltages as low as 1V and lower. A large part of the design process can also be embedded in a standard digital synthesis flow