Radio frequency interference detection and mitigation techniques for navigation and Earth observation

Radio-Frequency Interference (RFI) signals are undesired signals that degrade or disrupt the performance of a wireless receiver. RFI signals can be troublesome for any receiver, but they are especially threatening for applications that use very low power signals. This is the case of applications that rely on the Global Navigation Satellite Systems (GNSS), or passive microwave remote sensing applications such as Microwave Radiometry (MWR) and GNSS-Reflectometry (GNSS-R). In order to solve the problem of RFI, RFI-countermeasures are under development. This PhD thesis is devoted to the design, implementation and test of innovative RFI-countermeasures in the fields of MWR and GNSS. In the part devoted to RFI-countermeasures for MWR applications, first, this PhD thesis completes the development of the MERITXELL instrument. The MERITXELL is a multi-frequency total-power radiometer conceived to be an outstanding platform to perform detection, characterization, and localization of RFI signals at the most common MWR imaging bands up to 92 GHz. Moreover, a novel RFI mitigation technique is proposed for MWR: the Multiresolution Fourier Transform (MFT). An assessment of the performance of the MFT has been carried out by comparison with other time-frequency mitigation techniques. According to the results, the MFT technique is a good trade-off solution among all other techniques since it can mitigate efficiently all kinds of RFI signals under evaluation. In the part devoted to RFI-countermeasures for GNSS and GNSS-R applications, first, a system for RFI detection and localization at GNSS bands is proposed. This system is able to detect RFI signals at the L1 band with a sensitivity of -108 dBm at full-band, and of -135 dBm for continuous wave and chirp-like signals when using the averaged spectrum technique. Besides, the Generalized Spectral Separation Coefficient (GSSC) is proposed as a figure of merit to evaluate the Signal-to-Noise Ratio (SNR) degradation in the Delay-Doppler Maps (DDMs) due to the external RFI effect. Furthermore, the FENIX system has been conceived as an innovative system for RFI detection and mitigation and anti-jamming for GNSS and GNSS-R applications. FENIX uses the MFT blanking as a pre-correlation excision tool to perform the mitigation. In addition, FENIX has been designed to be cross-GNSS compatible and RFI-independent. The principles of operation of the MFT blanking algorithm are assessed and compared with other techniques for GNSS signals. Its performance as a mitigation tool is proven using GNSS-R data samples from a real airborne campaign. After that, the main building blocks of the patented architecture of FENIX have been described. The FENIX architecture has been implemented in three real-time prototypes. Moreover, a simulator named FENIX-Sim allows for testing its performance under different jamming scenarios. The real-time performance of FENIX prototype has been tested using different setups. First, a customized VNA has been built in order to measure the transfer function of FENIX in the presence of several representative RFI/jamming signals. The results show how the power transfer function adapts itself to mitigate the RFI/jamming signal. Moreover, several real-time tests with GNSS receivers have been performed using GPS L1 C/A, GPS L2C, and Galileo E1OS. The results show that FENIX provides an extra resilience against RFI and jamming signals up to 30 dB. Furthermore, FENIX is tested using a real GNSS timing setup. Under nominal conditions, when no RFI/jamming signal is present, a small additional jitter on the order of 2-4 ns is introduced in the system. Besides, a maximum bias of 45 ns has been measured under strong jamming conditions (-30 dBm), which is acceptable for current timing systems requiring accuracy levels of 100 ns. Finally, the design of a backup system for GNSS in tracking applications that require high reliability against RFI and jamming attacks is proposed.Les interferències de radiofreqüència (RFI) són senyals no desitjades que degraden o interrompen el funcionament dels receptors sense fils. Les RFI poden suposar un problema per qualsevol receptor, però són especialment amenaçadores per les a aplicacions que fan servir senyals de molt baixa potència. Aquest és el cas de les aplicacions que depenen dels sistemes mundials de navegació per satèl·lit (GNSS) o de les aplicacions de teledetecció passiva de microones, com la radiometria de microones (MWR) i la reflectometria GNSS (GNSS-R). Per combatre aquest problema, sistemes anti-RFI s'estan desenvolupament actualment. Aquesta tesi doctoral està dedicada al disseny, la implementació i el test de sistemes anti-RFI innovadors en els camps de MWR i GNSS. A la part dedicada als sistemes anti-RFI en MWR, aquesta tesi doctoral completa el desenvolupament de l'instrument MERITXELL. El MERITXELL és un radiòmetre multifreqüència concebut com una plataforma excepcional per la detecció, caracterització i localització de RFI a les bandes de MWR més utilitzades per sota dels 92 GHz. A més a més, es proposa una nova tècnica de mitigació de RFI per MWR: la Transformada de Fourier amb Multiresolució (MFT). El funcionament de la MFT s'ha comparat amb el d'altres tècniques de mitigació en els dominis del temps i la freqüència. D'acord amb els resultats obtinguts, la MFT és una bona solució de compromís entre les altres tècniques, ja que pot mitigar de manera eficient tots els tipus de senyals RFI considerats. A la part dedicada als sistemes anti-RFI en GNSS i GNSS-R, primer es proposa un sistema per a la detecció i localització de RFI a les bandes GNSS. Aquest sistema és capaç de detectar senyals RFI a la banda L1 amb una sensibilitat de -108 dBm a tota la banda, i de -135 dBm per a senyals d'ona contínua i chirp fen un mitjana de l'espectre. A més a més, el Coeficient de Separació Espectral Generalitzada (GSSC) es proposa com una mesura per avaluar la degradació de la relació senyal a soroll (SNR) en els Mapes de Delay-Doppler (DDM) a causa del impacte de les RFI. La major contribució d'aquesta tesi doctoral és el sistema FENIX. FENIX és un sistema innovador de detecció i mitigació de RFI i inhibidors de freqüència per aplicacions GNSS i GNSS-R. FENIX utilitza la MFT per eliminar la interferència abans del procés de correlació amb el codi GNSS independentment del tipus de RFI. L'algoritme de mitigació de FENIX s'ha avaluat i comparat amb altres tècniques i els principals components de la seva arquitectura patentada es descriuen. Finalment, un simulador anomenat FENIX-Sim permet avaluar el seu rendiment en diferents escenaris d'interferència. El funcionament en temps real del prototip FENIX ha estat provat utilitzant diferents mètodes. En primer lloc, s'ha creat un analitzador de xarxes per a mesurar la funció de transferència del FENIX en presència de diverses RFI representatives. Els resultats mostren com la funció de transferència s'adapta per mitigar el senyal interferent. A més a més, s'han realitzat diferents proves en temps real amb receptors GNSS compatibles amb els senyals GPS L1 C/A, GPS L2C i Galileo E1OS. Els resultats mostren que FENIX proporciona una resistència addicional contra les RFI i els senyals dels inhibidors de freqüència de fins a 30 dB. A més a més, FENIX s'ha provat amb un sistema comercial de temporització basat en GNSS. En condicions nominals, sense RFI, FENIX introdueix un petit error addicional de tan sols 2-4 ns. Per contra, el biaix màxim mesurat en condicions d'alta interferència (-30 dBm) és de 45 ns, el qual és acceptable per als sistemes de temporització actuals que requereixen nivells de precisió d'uns 100 ns. Finalment, es proposa el disseny d'un sistema robust de seguiment, complementari als GNSS, per a aplicacions que requereixen alta fiabilitat contra RFI.Postprint (published version

Definizione, studio e progetto preliminare di una tecnica di geo-localizzazione di sorgenti interferenti per satelliti commerciali di telecomunicazioni

L’argomento del dottorato riguarda le telecomunicazioni satellitari commerciali. In particolare tratta della possibilità di poter definire, progettare e valutare mediante analisi e simulazioni, un sistema in grado di geo-localizzare sorgenti interferenti nell’area di copertura dell’antenna a bordo satellite per telecomunicazioni (area di servizio). Tale soluzione tecnologica rappresenta un valido supporto per intervenire a seguito di uno o più eventi interferenti. Tale intervento può essere o di tipo passivo, quanto il satellite non è provvisto di sotto-sistema di contromisura, oppure attivo quando il satellite è provvisto a bordo di sistema di contromisura

Beam Tracking Strategies for 5G New Radio Networks Operating in the Millimetre Wave Bands

[ES] La llegada de la próxima generación del estándar de comunicaciones móviles, la llamada quinta generación (5G), es prácticamente una realidad. Las primeras redes comerciales han comenzado a ser desplegadas, centrándose en ofrecer altas velocidades de transferencia de datos. Sin embargo, el estándar 5G va mucho más allá y prevé dar soporte a nuevos servicios que pretenden revolucionar la sociedad. Estos nuevos servicios imponen un nivel alto de requisitos en no solo en cuanto a velocidad del tráfico de datos, sino en cuanto a latencia o número de dispositivos conectados simultáneamente. La amplia variedad de requisitos no puede ser soportada por las redes de cuarta generación (4G), por lo que se hizo necesario plantear un nuevo paradigma para las redes inalámbricas. Con la promesa de grandes cantidades de ancho de banda sin utilizar, el estándar 5G contempla utilizar frecuencias en la comúnmente conocida como banda de milimétricas (mmWave). Esta banda presenta grandes pérdidas de propagación, que se acentúan si existen bloqueos de señal. Actividades regulatorias del uso de las bandas de milimétricas atrajo el interés tanto de la industria como de la academia en plantear soluciones para dar servicio en estas bandas. En los últimos años se han presentado infinidad de trabajos basados en sistemas con múltiples antenas o MIMO, para conformar las señales transmitidas o recibidas en haces apuntando en determinadas direcciones. La ganancia que aportan los sistemas MIMO pueden compensar las altas pérdidas de propagación, asegurando la viabilidad de las comunicaciones mmWave. Se ha detectado una evidente falta de estudios sobre la viabilidad de sistemas MIMO en entornos móviles y dinámicos con bloqueos que hagan necesario que el sistema se reconfigure. Esta Tesis pretende cubrir este espacio desde un enfoque práctico y propone mecanismos de gestión de los haces para hacerles un seguimiento utilizando los recursos y mecanismos del nuevo estándar 5G. Las soluciones aportadas se basan en el uso eficiente de los reportes de medidas de las señales de referencia estandarizadas en enlace descendente. En primer lugar, esta Tesis recoge un análisis minucioso del estado del arte, donde se corrobora la necesidad de aportar soluciones de seguimiento de haces en sistemas de comunicaciones en la banda de milimétricas. Además, se estudian los diferentes mecanismos definidos en el estándar 5G y que posibilitan el seguimiento. Cabe destacar que el estándar no define un mecanismo único a seguir, permitiendo presentar propuestas. Una vez conocidas las tecnologías, se centra el estudio en el impacto del seguimiento sobre las prestaciones a nivel de red y de enlace. Dicho estudio se realiza sobre un sistema punto a punto, donde el terminal móvil se desplaza por un entorno urbano. En base a simulaciones de red, se cuantifica el índice de seguimiento de haz y de cómo dicho seguimiento afecta a la relación señal a ruido más interferencia (SINR) y la tasa de transmisión del usuario. Las soluciones de seguimiento propuestas en esta Tesis se pueden clasificar en dos categorías. En una primera categoría, se realiza el seguimiento en base a reportes de medidas de las señales de referencia. Independientemente de la velocidad, se alcanza un seguimiento del 91% con poca penalización en la tasa de transmisión si se monitorizan los haces de interés con una periodicidad menor de 20 ms. En la segunda categoría caben mecanismos de seguimiento que hacen uso de fuentes externas de información. Dentro de esta categoría, se propone un fingerprinting que relacione haces con la localización reportada y un modelo de machine learning (ML) que prediga los haces a utilizar. El fingerprinting proporciona los mismos niveles de rendimiento. Sin embargo, esta solución es muy sensible a errores y requiere considerar todos los casos posibles, lo que la hace tecnológicamente inviable. En cambio, el modelo de ML, que hace p[CA] L'arribada de la següent generació de l'estàndard de comunicacions mòbils, l'anomenada cinquena generació (5G), es pràcticament una realitat. Les primeres xarxes comercials han començat a desplegar-se i s'han centrat en oferir altes velocitats de transferència de dades. No obstant, l'estàndard 5G va molt mes allà y preveu donar suport a nous serveis que pretenen revolucionar la societat. Estos nous serveis imposen un alt nivell de requisits no sols en quant a velocitat de tràfic de dades, si no també en quant a latència o número de connexions simultànies. L'ampla varietat de requisits no es suportada per les xarxes de quarta generació (4G) actuals, per el qual es va fer necessari un nou paradigma de xarxes sense fil. Amb la promesa de amplies quantitats d'ample de banda, l'estàndard 5G contempla utilitzar freqüències a la banda de mil·limètriques. Esta banda presenta l'inconvenient d'experimentar grans pèrdues de propagació, que s'accentuen en cas de bloqueigs. L'apertura de les bandes de mil·limètriques va atraure l'interès tant de l'industria com de l'acadèmia en plantejar solucions per a donar servei en estes bandes. En els últims anys s'han presentat infinitat de treballs basats en sistemes amb múltiples antenes o MIMO, per a conformar els senyals transmesos o rebuts en feixos apuntant en determinades direccions d'interès. El guany de feix es pot utilitzar per a compensar les pèrdues de propagació, assegurant la viabilitat de les comunicacions en la banda de mil·limètriques. No obstant això, s'ha detectat una preocupant manca d'estudis sobre la viabilitat d'estos sistemes en entorns mòbils i dinàmics, amb obstacles que bloquejen els feixos i facen necessari que el sistema es reconfigure. El present treball de Tesi pretén cobrir este espai buit i des d'un punt de vista pràctic, es proposen mecanismes de gestió dels feixos per a ser el seguiment utilitzant els recursos i mecanismes dels que disposa l'estàndard 5G. D'esta manera, les solucions aportades es basen en la utilització eficient dels reports de mesures dels senyals de referència del enllaç descendent. En primer lloc, esta Tesi recull una anàlisi minuciosa de l'estat de l'art on es corrobora la necessitat de aportar solucions de seguiment de feixos per a comunicacions en la banda de freqüències mil·limètriques. A més a més, s'estudien els diferents mecanismes definits a l'estàndard 5G i que possibiliten el seguiment. Cap destacar que l'estàndard no defineix un mecanisme únic, si no que deixa la porta oberta a presentar propostes. Una vegada conegudes les tecnologies, l'estudi es centra en l'impacte del seguiment sobre les prestacions a nivell de xarxa i d'enllaç. Este estudi es realitza sobre un sistema MIMO punt a punt, en una única estació base i un terminal mòbil desplaçant-se en un entorn urbà. En base a simulacions d'extrem a extrem, es quantifica l'índex de seguiment de feix i com l'anomenat seguiment afecta a la relació senyal a soroll més interferència (SINR) i a la taxa instantània de transmissió de l'usuari. Les solucions de seguiment de feixos propostes a la Tesi es poden classificar en dos categories. A la primera categoria, el seguiment de feixos es realitza en base als reports de mesures dels senyals de referència. Independentment de la velocitat, s'arriba a una taxa de seguiment del 91% amb poca penalització de taxa de transmissió si els feixos d'interès es mesuren amb una periodicitat menor a 20 ms. A la segona categoria pertanyen els algoritmes que utilitzen fonts d'informació externes. Dins d'aquesta categoria es proposa un fingerprinting que relaciona un parell de feixos amb la ubicació de l'usuari, i a banda un model d'intel·ligència artificial (IA) que preveu el feix a utilitzar. El fingerprinting ofereix el mateix rendiment. Però, esta solució es molt sensible a errors i requereix considerar tots els casos possibles, fent-la tecnològicament inviable. En canvi, el[EN] The arrival of the next generation of mobile communication standards, the so-called Fifth Generation (5G), is already a reality. The first commercial networks have begun to be deployed, and they focus on providing higher data rates. However, the 5G standard goes much further from that and aims at providing support to new services which will revolutionise the society. These new services impose a high level of requirements not only in terms of the data traffic speed, but also in terms of very low latency or incredibly large number of simultaneous connections. This wide variety of requirements cannot be technologically supported by the current Fourth Generation (4G) networks, so it became necessary to move forward with a new paradigm for wireless networks. With the promise of large amounts of bandwidth, in the order of GHz, the 5G standard contemplates the use of frequencies in the commonly known Millimetre Wave (mmWave) band. The mmWave band experiences large propagation losses, which are accentuated in blockage events. Regulatory activities worldwide in the mmWave bands attracted the interest of both the industry and the academia. In the last few years, a tremendous number of contributions on mmWave propagation studies and networks have appeared, most of them based on Multiple-Input Multiple-Output (MIMO) solutions. MIMO architectures allow to beamform, which focuses the radiated energy on certain directions of interest called beams. The additional beam gain compensates the high propagation losses, ensuring the viability of the communications in the mmWave band. There is an evident lack of viability studies of mmWave MIMO systems in mobile and highly-dynamic environments, where obstacles may block beams and forcing frequent re-configurations. This Thesis work aims to fill this gap from a practical approach. This Thesis proposes beam management mechanisms utilising the mechanisms and resources offered by the Third Generation Partnership Project (3GPP) 5G radio access standard: 5G New Radio (NR). The practical solutions are based on the efficient use of measurement reports of standardised downlink Reference Signals (RS). In first place, this Thesis provides a thorough state-of-the-art analysis and corroborates the need of adopting beam tracking solutions for mmWave networks. Then, a complete overview of the 5G standard mechanisms that enable beam tracking is given. The NR standard does not define a standardised mechanism for beam tracking, leaving the door open to proposals to carry out such monitoring. Once the technologies have been identified, the Thesis continues with assessing the impact of the beam tracking strategies on the network and link-level performance. The study is focused on individual point-to-point mmWave links in a realistic urban environment. Based on end-to-end network simulations, the Thesis is interested in assessing the beam tracking success ratio and how beam misalignment affects the perceived Signal to Noise plus Interference Ratio (SINR) and user throughput at pedestrian and vehicular speeds. The beam tracking solutions proposed in this Thesis fall into two categories. The first category monitors beams based on measuring and reporting beamformed RS. Regardless of the speed, this beam tracking category provides up to 91 % tracking performance, with little throughput reduction if the beams of interest are measured with a periodicity below 20 ms. Beam tracking in the second category relies on external information sources. Within this category, this Thesis proposes a fingerprinting database relating beams to the user position and a machine learning (ML) model. Fingerprinting beam tracking is technologically viable and provides similar performance levels. However, this solution is very sensitive to errors and requires considering all possible situations. The ML beam tracking, which makes predictions with a 16 % of estimation error for the reference data set.I want to thank the Spanish Ministry of Education and Professional Formation for funding this Thesis work with an official pre-doctoral contract grant.Herranz Claveras, C. (2019). Beam Tracking Strategies for 5G New Radio Networks Operating in the Millimetre Wave Bands [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/130845TESI

Advanced Modulation and Coding Technology Conference

The objectives, approach, and status of all current LeRC-sponsored industry contracts and university grants are presented. The following topics are covered: (1) the LeRC Space Communications Program, and Advanced Modulation and Coding Projects; (2) the status of four contracts for development of proof-of-concept modems; (3) modulation and coding work done under three university grants, two small business innovation research contracts, and two demonstration model hardware development contracts; and (4) technology needs and opportunities for future missions

Synchronization and Parameter Estimation in Wireless Communications

This dissertation is devoted to the design and analysis of synchronization and channel parameter estimation schemes in wireless communications. Intrigued by the observation that the information is conveyed through wireless channels by uniformly spaced pulses that are some kind of "distorted" convolution of data symbols and a shaping pulse, we try to set up a framework to study synchronization and channel parameter estimation problems in the frequency domain. The dissertation consists of four major parts. Many issues in digital communications and signal processing involve the analysis of the inverse of Toeplitz matrices. In the first part, the convergence of the inverse of Toeplitz matrices and its application are presented. Under the condition that the $z$-transform of the sequence with which the Toeplitz matrices are associated has no zero on the unit circle, we show that the inverse converges to a circular matrix in the weak sense. Furthermore, for the finite boundary quadratic form, a sufficient condition under which the convergence can be strengthened into the strong sense and an upper bound of the approximation residue error are derived. It is well known that a circular matrix can be eigendecomposed by the discrete Fourier transform (DFT) which provides the desired frequency domain approach. In practical systems, synchronization parameters such as timing and carrier phase offsets, and channel response in fading channels are acquired with the help of a training sequence (TS) that is known to the receiver, which is called the data-aided (DA) estimation. In the second part, the performance limit that is the Cramer-Rao lower Bound (CRB) for the DA joint carrier phase and timing offsets estimation with an arbitrary TS is derived using the properties of Toeplitz matrices. Unlike the CRB derived in the literature, the bound derived in this dissertation reveals the close relation between a TS and its resultant performance limit, therefore it provides a quantitative approach to design TS for the acquisition of synchronization parameters. Following the estimation theorem, we derive a maximum likelihood (ML) slow frequency-selective fading channel estimator using the frequency domain approach introduced by the properties of Toeplitz matrices in the third part. In the fourth part, a carrier frequency offset estimator and a joint carrier phase and timing offset estimators with moderate complexities are proposed. Their systolic VLSI implementations are also presented. The performance of the proposed estimators approaches their corresponding performance limits. <p

Monostatic Airborne Synthetic Aperture Radar Using Commercial WiMAX Transceivers In the License-exempt Spectrum

The past half-century witnessed an evolution of synthetic aperture radar (SAR). Boosted by digital signal processing (DSP), a variety of SAR imaging algorithms have been developed, in which the wavenumber domain algorithm is mature for airborne SAR and independent of signal waveforms. Apart from the algorithm development, there is a growing interest in how to acquire the raw data of targets’ echoes before the DSP for SAR imaging in a cost-effective way. For the data acquisition, various studies over the past 15 years have shed light on utilizing the signal generated from the ubiquitous broadband wireless technology – orthogonal frequency division multiplexing (OFDM). However, the purpose of this thesis is to enable commercial OFDM-based wireless systems to work as an airborne SAR sensor. The unlicensed devices of Worldwide interoperability for Microwave Access (WiMAX) are the first option, owing to their accessibility, similarity and economy. This dissertation first demonstrates the feasibility of applying WiMAX to SAR by discussing their similar features. Despite the similarities they share, the compatibility of the two technologies is undermined by a series of problems resulted from WiMAX transceiver mechanisms and industrial rules for radiated power. In order to directly apply commercial WiMAX base station transceivers in unlicensed band to airborne SAR application, we propose a radio-frequency (RF) front design together with a signal processing means. To be specific, a double-pole, double-throw (DPDT) switch is inserted between an antenna and two WiMAX transceivers for generating pulsed signal. By simulations, the transmitted power of the SAR sensor is lower than 0dBm, while its imaging range can be over 10km for targets with relatively large radar cross section (RCS), such as a ship. Its range resolution is 9.6m whereas its cross-range resolution is finer than 1m. Equipped with the multi-mode, this SAR sensor is further enhanced to satisfy the requirements of diversified SAR applications. For example, the width of the scan-mode SAR’s range swath is 2.1km, over five times the width of other modes. Vital developed Matlab code is given in Appendix D, and its correctness is shown by comparing with the image of chirped SAR. To summarize, the significance of this dissertation is to propose, for the first time, a design of directly leveraging commercial OFDM-based systems for airborne SAR imaging. Compared with existing designs of airborne SAR, it is a promising low-cost solution

Proceedings of the Second International Mobile Satellite Conference (IMSC 1990)

Presented here are the proceedings of the Second International Mobile Satellite Conference (IMSC), held June 17-20, 1990 in Ottawa, Canada. Topics covered include future mobile satellite communications concepts, aeronautical applications, modulation and coding, propagation and experimental systems, mobile terminal equipment, network architecture and control, regulatory and policy considerations, vehicle antennas, and speech compression

Advanced signal processing tools for ballistic missile defence and space situational awareness

The research presented in this Thesis deals with signal processing algorithms for the classification of sensitive targets for defence applications and with novel solutions for the detection of space objects. These novel tools include classification algorithms for Ballistic Targets (BTs) from both micro-Doppler (mD) and High Resolution Range Profiles (HRRPs) of a target, and a space-borne Passive Bistatic Radar (PBR) designed for exploiting the advantages guaranteed by the Forward Scattering (FS) configuration for the detection and identification of targets orbiting around the Earth.;Nowadays the challenge of the identification of Ballistic Missile (BM) warheads in a cloud of decoys and debris is essential in order to optimize the use of ammunition resources. In this Thesis, two different and efficient robust frameworks are presented. Both the frameworks exploit in different fashions the effect in the radar return of micro-motions exhibited by the target during its flight.;The first algorithm analyses the radar echo from the target in the time-frequency domain, with the aim to extract the mD information. Specifically, the Cadence Velocity Diagram (CVD) from the received signal is evaluated as mD profile of the target, where the mD components composing the radar echo and their repetition rates are shown.;Different feature extraction approaches are proposed based on the estimation of statistical indices from the 1-Dimensional (1D) Averaged CVD (ACVD), on the evaluation of pseudo-Zerike (pZ) and Krawtchouk (Kr) image moments and on the use of 2-Dimensional (2D) Gabor filter, considering the CVD as 2D image. The reliability of the proposed feature extraction approaches is tested on both simulated and real data, demonstrating the adaptivity of the framework to different radar scenarios and to different amount of available resources.;The real data are realized in laboratory, conducting an experiment for simulating the mD signature of a BT by using scaled replicas of the targets, a robotic manipulator for the micro-motions simulation and a Continuous Waveform (CW) radar for the radar measurements.;The second algorithm is based on the computation of the Inverse Radon Transform (IRT) of the target signature, represented by a HRRP frame acquired within an entire period of the main rotating motion of the target, which are precession for warheads and tumbling for decoys. Following, pZ moments of the resulting transformation are evaluated as final feature vector for the classifier. The features guarantee robustness against the target dimensions and the initial phase and the angular velocity of its motion.;The classification results on simulated data are shown for different polarization of the ElectroMagnetic (EM) radar waveform and for various operational conditions, confirming the the validity of the algorithm.The knowledge of space debris population is of fundamental importance for the safety of both the existing and new space missions. In this Thesis, a low budget solution to detect and possibly track space debris and satellites in Low Earth Orbit (LEO) is proposed.;The concept consists in a space-borne PBR installed on a CubeSaT flying at low altitude and detecting the occultations of radio signals coming from existing satellites flying at higher altitudes. The feasibility of such a PBR system is conducted, with key performance such as metrics the minimumsize of detectable objects, taking into account visibility and frequency constraints on existing radio sources, the receiver size and the compatibility with current CubeSaT's technology.;Different illuminator types and receiver altitudes are considered under the assumption that all illuminators and receivers are on circular orbits. Finally, the designed system can represent a possible solution to the the demand for Ballistic Missile Defence (BMD) systems able to provide early warning and classification and its potential has been assessed also for this purpose.The research presented in this Thesis deals with signal processing algorithms for the classification of sensitive targets for defence applications and with novel solutions for the detection of space objects. These novel tools include classification algorithms for Ballistic Targets (BTs) from both micro-Doppler (mD) and High Resolution Range Profiles (HRRPs) of a target, and a space-borne Passive Bistatic Radar (PBR) designed for exploiting the advantages guaranteed by the Forward Scattering (FS) configuration for the detection and identification of targets orbiting around the Earth.;Nowadays the challenge of the identification of Ballistic Missile (BM) warheads in a cloud of decoys and debris is essential in order to optimize the use of ammunition resources. In this Thesis, two different and efficient robust frameworks are presented. Both the frameworks exploit in different fashions the effect in the radar return of micro-motions exhibited by the target during its flight.;The first algorithm analyses the radar echo from the target in the time-frequency domain, with the aim to extract the mD information. Specifically, the Cadence Velocity Diagram (CVD) from the received signal is evaluated as mD profile of the target, where the mD components composing the radar echo and their repetition rates are shown.;Different feature extraction approaches are proposed based on the estimation of statistical indices from the 1-Dimensional (1D) Averaged CVD (ACVD), on the evaluation of pseudo-Zerike (pZ) and Krawtchouk (Kr) image moments and on the use of 2-Dimensional (2D) Gabor filter, considering the CVD as 2D image. The reliability of the proposed feature extraction approaches is tested on both simulated and real data, demonstrating the adaptivity of the framework to different radar scenarios and to different amount of available resources.;The real data are realized in laboratory, conducting an experiment for simulating the mD signature of a BT by using scaled replicas of the targets, a robotic manipulator for the micro-motions simulation and a Continuous Waveform (CW) radar for the radar measurements.;The second algorithm is based on the computation of the Inverse Radon Transform (IRT) of the target signature, represented by a HRRP frame acquired within an entire period of the main rotating motion of the target, which are precession for warheads and tumbling for decoys. Following, pZ moments of the resulting transformation are evaluated as final feature vector for the classifier. The features guarantee robustness against the target dimensions and the initial phase and the angular velocity of its motion.;The classification results on simulated data are shown for different polarization of the ElectroMagnetic (EM) radar waveform and for various operational conditions, confirming the the validity of the algorithm.The knowledge of space debris population is of fundamental importance for the safety of both the existing and new space missions. In this Thesis, a low budget solution to detect and possibly track space debris and satellites in Low Earth Orbit (LEO) is proposed.;The concept consists in a space-borne PBR installed on a CubeSaT flying at low altitude and detecting the occultations of radio signals coming from existing satellites flying at higher altitudes. The feasibility of such a PBR system is conducted, with key performance such as metrics the minimumsize of detectable objects, taking into account visibility and frequency constraints on existing radio sources, the receiver size and the compatibility with current CubeSaT's technology.;Different illuminator types and receiver altitudes are considered under the assumption that all illuminators and receivers are on circular orbits. Finally, the designed system can represent a possible solution to the the demand for Ballistic Missile Defence (BMD) systems able to provide early warning and classification and its potential has been assessed also for this purpose

Second year technical report on-board processing for future satellite communications systems

Advanced baseband and microwave switching techniques for large domestic communications satellites operating in the 30/20 GHz frequency bands are discussed. The nominal baseband processor throughput is one million packets per second (1.6 Gb/s) from one thousand T1 carrier rate customer premises terminals. A frequency reuse factor of sixteen is assumed by using 16 spot antenna beams with the same 100 MHz bandwidth per beam and a modulation with a one b/s per Hz bandwidth efficiency. Eight of the beams are fixed on major metropolitan areas and eight are scanning beams which periodically cover the remainder of the U.S. under dynamic control. User signals are regenerated (demodulated/remodulated) and message packages are reformatted on board. Frequency division multiple access and time division multiplex are employed on the uplinks and downlinks, respectively, for terminals within the coverage area and dwell interval of a scanning beam. Link establishment and packet routing protocols are defined. Also described is a detailed design of a separate 100 x 100 microwave switch capable of handling nonregenerated signals occupying the remaining 2.4 GHz bandwidth with 60 dB of isolation, at an estimated weight and power consumption of approximately 400 kg and 100 W, respectively