Design exploration and performance strategies towards power-efficient FPGA-based achitectures for sound source localization

Many applications rely on MEMS microphone arrays for locating sound sources prior to their execution. Those applications not only are executed under real-time constraints but also are often embedded on low-power devices. These environments become challenging when increasing the number of microphones or requiring dynamic responses. Field-Programmable Gate Arrays (FPGAs) are usually chosen due to their flexibility and computational power. This work intends to guide the design of reconfigurable acoustic beamforming architectures, which are not only able to accurately determine the sound Direction-Of-Arrival (DoA) but also capable to satisfy the most demanding applications in terms of power efficiency. Design considerations of the required operations performing the sound location are discussed and analysed in order to facilitate the elaboration of reconfigurable acoustic beamforming architectures. Performance strategies are proposed and evaluated based on the characteristics of the presented architecture. This power-efficient architecture is compared to a different architecture prioritizing performance in order to reveal the unavoidable design trade-offs

Baseband analog front-end and digital back-end for reconfigurable multi-standard terminals

Multimedia applications are driving wireless network operators to add high-speed data services such as Edge (E-GPRS), WCDMA (UMTS) and WLAN (IEEE 802.11a,b,g) to the existing GSM network. This creates the need for multi-mode cellular handsets that support a wide range of communication standards, each with a different RF frequency, signal bandwidth, modulation scheme etc. This in turn generates several design challenges for the analog and digital building blocks of the physical layer. In addition to the above-mentioned protocols, mobile devices often include Bluetooth, GPS, FM-radio and TV services that can work concurrently with data and voice communication. Multi-mode, multi-band, and multi-standard mobile terminals must satisfy all these different requirements. Sharing and/or switching transceiver building blocks in these handsets is mandatory in order to extend battery life and/or reduce cost. Only adaptive circuits that are able to reconfigure themselves within the handover time can meet the design requirements of a single receiver or transmitter covering all the different standards while ensuring seamless inter-interoperability. This paper presents analog and digital base-band circuits that are able to support GSM (with Edge), WCDMA (UMTS), WLAN and Bluetooth using reconfigurable building blocks. The blocks can trade off power consumption for performance on the fly, depending on the standard to be supported and the required QoS (Quality of Service) leve

Enhancing Real-time Embedded Image Processing Robustness on Reconfigurable Devices for Critical Applications

Nowadays, image processing is increasingly used in several application fields, such as biomedical, aerospace, or automotive. Within these fields, image processing is used to serve both non-critical and critical tasks. As example, in automotive, cameras are becoming key sensors in increasing car safety, driving assistance and driving comfort. They have been employed for infotainment (non-critical), as well as for some driver assistance tasks (critical), such as Forward Collision Avoidance, Intelligent Speed Control, or Pedestrian Detection. The complexity of these algorithms brings a challenge in real-time image processing systems, requiring high computing capacity, usually not available in processors for embedded systems. Hardware acceleration is therefore crucial, and devices such as Field Programmable Gate Arrays (FPGAs) best fit the growing demand of computational capabilities. These devices can assist embedded processors by significantly speeding-up computationally intensive software algorithms. Moreover, critical applications introduce strict requirements not only from the real-time constraints, but also from the device reliability and algorithm robustness points of view. Technology scaling is highlighting reliability problems related to aging phenomena, and to the increasing sensitivity of digital devices to external radiation events that can cause transient or even permanent faults. These faults can lead to wrong information processed or, in the worst case, to a dangerous system failure. In this context, the reconfigurable nature of FPGA devices can be exploited to increase the system reliability and robustness by leveraging Dynamic Partial Reconfiguration features. The research work presented in this thesis focuses on the development of techniques for implementing efficient and robust real-time embedded image processing hardware accelerators and systems for mission-critical applications. Three main challenges have been faced and will be discussed, along with proposed solutions, throughout the thesis: (i) achieving real-time performances, (ii) enhancing algorithm robustness, and (iii) increasing overall system's dependability. In order to ensure real-time performances, efficient FPGA-based hardware accelerators implementing selected image processing algorithms have been developed. Functionalities offered by the target technology, and algorithm's characteristics have been constantly taken into account while designing such accelerators, in order to efficiently tailor algorithm's operations to available hardware resources. On the other hand, the key idea for increasing image processing algorithms' robustness is to introduce self-adaptivity features at algorithm level, in order to maintain constant, or improve, the quality of results for a wide range of input conditions, that are not always fully predictable at design-time (e.g., noise level variations). This has been accomplished by measuring at run-time some characteristics of the input images, and then tuning the algorithm parameters based on such estimations. Dynamic reconfiguration features of modern reconfigurable FPGA have been extensively exploited in order to integrate run-time adaptivity into the designed hardware accelerators. Tools and methodologies have been also developed in order to increase the overall system dependability during reconfiguration processes, thus providing safe run-time adaptation mechanisms. In addition, taking into account the target technology and the environments in which the developed hardware accelerators and systems may be employed, dependability issues have been analyzed, leading to the development of a platform for quickly assessing the reliability and characterizing the behavior of hardware accelerators implemented on reconfigurable FPGAs when they are affected by such faults

Embedded electronic systems driven by run-time reconfigurable hardware

Abstract This doctoral thesis addresses the design of embedded electronic systems based on run-time reconfigurable hardware technology –available through SRAM-based FPGA/SoC devices– aimed at contributing to enhance the life quality of the human beings. This work does research on the conception of the system architecture and the reconfiguration engine that provides to the FPGA the capability of dynamic partial reconfiguration in order to synthesize, by means of hardware/software co-design, a given application partitioned in processing tasks which are multiplexed in time and space, optimizing thus its physical implementation –silicon area, processing time, complexity, flexibility, functional density, cost and power consumption– in comparison with other alternatives based on static hardware (MCU, DSP, GPU, ASSP, ASIC, etc.). The design flow of such technology is evaluated through the prototyping of several engineering applications (control systems, mathematical coprocessors, complex image processors, etc.), showing a high enough level of maturity for its exploitation in the industry.Resumen Esta tesis doctoral abarca el diseño de sistemas electrónicos embebidos basados en tecnología hardware dinámicamente reconfigurable –disponible a través de dispositivos lógicos programables SRAM FPGA/SoC– que contribuyan a la mejora de la calidad de vida de la sociedad. Se investiga la arquitectura del sistema y del motor de reconfiguración que proporcione a la FPGA la capacidad de reconfiguración dinámica parcial de sus recursos programables, con objeto de sintetizar, mediante codiseño hardware/software, una determinada aplicación particionada en tareas multiplexadas en tiempo y en espacio, optimizando así su implementación física –área de silicio, tiempo de procesado, complejidad, flexibilidad, densidad funcional, coste y potencia disipada– comparada con otras alternativas basadas en hardware estático (MCU, DSP, GPU, ASSP, ASIC, etc.). Se evalúa el flujo de diseño de dicha tecnología a través del prototipado de varias aplicaciones de ingeniería (sistemas de control, coprocesadores aritméticos, procesadores de imagen, etc.), evidenciando un nivel de madurez viable ya para su explotación en la industria.Resum Aquesta tesi doctoral està orientada al disseny de sistemes electrònics empotrats basats en tecnologia hardware dinàmicament reconfigurable –disponible mitjançant dispositius lògics programables SRAM FPGA/SoC– que contribueixin a la millora de la qualitat de vida de la societat. S’investiga l’arquitectura del sistema i del motor de reconfiguració que proporcioni a la FPGA la capacitat de reconfiguració dinàmica parcial dels seus recursos programables, amb l’objectiu de sintetitzar, mitjançant codisseny hardware/software, una determinada aplicació particionada en tasques multiplexades en temps i en espai, optimizant així la seva implementació física –àrea de silici, temps de processat, complexitat, flexibilitat, densitat funcional, cost i potència dissipada– comparada amb altres alternatives basades en hardware estàtic (MCU, DSP, GPU, ASSP, ASIC, etc.). S’evalúa el fluxe de disseny d’aquesta tecnologia a través del prototipat de varies aplicacions d’enginyeria (sistemes de control, coprocessadors aritmètics, processadors d’imatge, etc.), demostrant un nivell de maduresa viable ja per a la seva explotació a la indústria

High-speed dynamic partial reconfiguration for field programmable gate arrays

With dynamically and partially reconfigurable designs, it is necessary that the speed of the reconfiguration be accomplished in a time that is sufficiently small such that the operation of reconfiguration is not the limiting factor in the process. Therefore, the communication between the source of configuration and the configurable unit must be made as fast as possible. The aim of this work is to use an embedded controller internal to the FPGA to control the reconfiguration process and obtain the maximum speed at which reconfiguration can occur, with current FPGA technology. The use of Direct Memory Access (DMA) driven operations instead of the current arbitrated bus architectures yielded a 30% increase in the speed of reconfiguration compared to other methods such as OPB_HWICAP and PLB_HWICAP [1]. The use of interrupt driven partial reconfiguration was also introduced, allowing the processor to switch to other tasks during the reconfiguration operation. All of these contributions lead to significant performance improvements over current partial reconfiguration subsystems. The configuration controller was tested using four partially reconfigurable system implementations: (i) one targeting the Hard IP PowerPC405 on Virtex-4, (ii) a second targeting the Soft IP MicroBlaze on Virtex-5, (iii) a third targeting the Hard IP PowerPC440 on Virtex-5, and (iv) a fourth system targets the Hard IP PowerPC440 on Virtex-5 capable of adaptive feedback. The adaptive feedback Virtex-5 system can use internal voltage and temperature measurements from the Xilinx System Monitor IP to dynamically increase or decrease the speed of reconfiguration and/or change other reconfigurable aspects of the system to better match the environment

Ein flexibles, heterogenes Bildverarbeitungs-Framework für weltraumbasierte, rekonfigurierbare Datenverarbeitungsmodule

Scientific instruments as payload of current space missions are often equipped with high-resolution sensors. Thereby, especially camera-based instruments produce a vast amount of data. To obtain the desired scientific information, this data usually is processed on ground. Due to the high distance of missions within the solar system, the data rate for downlink to the ground station is strictly limited. The volume of scientific relevant data is usually less compared to the obtained raw data. Therefore, processing already has to be carried out on-board the spacecraft. An example of such an instrument is the Polarimetric and Helioseismic Imager (PHI) on-board Solar Orbiter. For acquisition, storage and processing of images, the instrument is equipped with a Data Processing Module (DPM). It makes use of heterogeneous computing based on a dedicated LEON3 processor in combination with two reconfigurable Xilinx Virtex-4 Field-Programmable Gate Arrays (FPGAs). The thesis will provide an overview of the available space-grade processing components (processors and FPGAs) which fulfill the requirements of deepspace missions. It also presents existing processing platforms which are based upon a heterogeneous system combining processors and FPGAs. This also includes the DPM of the PHI instrument, whose architecture will be introduced in detail. As core contribution of this thesis, a framework will be presented which enables high-performance image processing on such hardware-based systems while retaining software-like flexibility. This framework mainly consists of a variety of modules for hardware acceleration which are integrated seamlessly into the data flow of the on-board software. Supplementary, it makes extensive use of the dynamic in-flight reconfigurability of the used Virtex-4 FPGAs. The flexibility of the presented framework is proven by means of multiple examples from within the image processing of the PHI instrument. The framework is analyzed with respect to processing performance as well as power consumption.Wissenschaftliche Instrumente auf aktuellen Raumfahrtmissionen sind oft mit hochauflösenden Sensoren ausgestattet. Insbesondere kamerabasierte Instrumente produzieren dabei eine große Menge an Daten. Diese werden üblicherweise nach dem Empfang auf der Erde weiterverarbeitet, um daraus wissenschaftlich relevante Informationen zu gewinnen. Aufgrund der großen Entfernung von Missionen innerhalb unseres Sonnensystems ist die Datenrate zur Übertragung an die Bodenstation oft sehr begrenzt. Das Volumen der wissenschaftlich relevanten Daten ist meist deutlich kleiner als die aufgenommenen Rohdaten. Daher ist es vorteilhaft, diese bereits an Board der Sonde zu verarbeiten. Ein Beispiel für solch ein Instrument ist der Polarimetric and Helioseismic Imager (PHI) an Bord von Solar Orbiter. Um die Daten aufzunehmen, zu speichern und zu verarbeiten, ist das Instrument mit einem Data Processing Module (DPM) ausgestattet. Dieses nutzt ein heterogenes Rechnersystem aus einem dedizierten LEON3 Prozessor, zusammen mit zwei rekonfigurierbaren Xilinx Virtex-4 Field-Programmable Gate Arrays (FPGAs). Die folgende Arbeit gibt einen Überblick über verfügbare Komponenten zur Datenverarbeitung (Prozessoren und FPGAs), die den Anforderungen von Raumfahrtmissionen gerecht werden, und stellt einige existierende Plattformen vor, die auf einem heterogenen System aus Prozessor und FPGA basieren. Hierzu gehört auch das Data Processing Module des PHI Instrumentes, dessen Architektur im Verlauf dieser Arbeit beschrieben wird. Als Kernelement der Dissertation wird ein Framework vorgestellt, das sowohl eine performante, als auch eine flexible Bilddatenverarbeitung auf einem solchen System ermöglicht. Dieses Framework besteht aus verschiedenen Modulen zur Hardwarebeschleunigung und bindet diese nahtlos in den Datenfluss der On-Board Software ein. Dabei wird außerdem die Möglichkeit genutzt, die eingesetzten Virtex-4 FPGAs dynamisch zur Laufzeit zu rekonfigurieren. Die Flexibilität des vorgestellten Frameworks wird anhand mehrerer Fallbeispiele aus der Bildverarbeitung von PHI dargestellt. Das Framework wird bezüglich der Verarbeitungsgeschwindigkeit und Energieeffizienz analysiert

The development of a node for a hardware reconfigurable parallel processor

This dissertation concerns the design and implementation of a node for a hardware reconfigurable parallel processor. The hardware that was developed allows for the further development of a parallel processor with configurable hardware acceleration. Each node in the system has a standard microprocessor and reconfigurable logic device and has high speed communications channels for inter-node communication. The design of the node provided high-speed serial communications channels allowing the implementation of various network topographies. The node also provided a PCI master interface to provide an external interface and communicate with local nodes on the bus. A high speed RlSC processor provided communication and system control functions and the reconfigurable logic device provided communication interfaces and data processing functions. The node was designed and implemented as a PCI card that interfaced a standard PCI bus. VHDL designs for logic devices that provided system support were developed, VHDL designs for the reconfigurable logic FPGA and software including drivers and system software were written for the node. The 64-bit version Linux operating system was then ported to the processor providing a UNIX environment for the system. The node functioned as specified and parallel and hardware accelerated processing was demonstrated. The hardware acceleration was shown to provide substantial performance benefits for the system

Optimising and evaluating designs for reconfigurable hardware

Growing demand for computational performance, and the rising cost for chip design and manufacturing make reconfigurable hardware increasingly attractive for digital system implementation. Reconfigurable hardware, such as field-programmable gate arrays (FPGAs), can deliver performance through parallelism while also providing flexibility to enable application builders to reconfigure them. However, reconfigurable systems, particularly those involving run-time reconfiguration, are often developed in an ad-hoc manner. Such an approach usually results in low designer productivity and can lead to inefficient designs. This thesis covers three main achievements that address this situation. The first achievement is a model that captures design parameters of reconfigurable hardware and performance parameters of a given application domain. This model supports optimisations for several design metrics such as performance, area, and power consumption. The second achievement is a technique that enhances the relocatability of bitstreams for reconfigurable devices, taking into account heterogeneous resources. This method increases the flexibility of modules represented by these bitstreams while reducing configuration storage size and design compilation time. The third achievement is a technique to characterise the power consumption of FPGAs in different activity modes. This technique includes the evaluation of standby power and dedicated low-power modes, which are crucial in meeting the requirements for battery-based mobile devices

Dynamically reconfigurable management of energy, performance, and accuracy applied to digital signal, image, and video Processing Applications

There is strong interest in the development of dynamically reconfigurable systems that can meet real-time constraints in energy/power-performance-accuracy (EPA/PPA). In this dissertation, I introduce a framework for implementing dynamically reconfigurable digital signal, image, and video processing systems. The basic idea is to first generate a collection of Pareto-optimal realizations in the EPA/PPA space. Dynamic EPA/PPA management is then achieved by selecting the Pareto-optimal implementations that can meet the real-time constraints. The systems are then demonstrated using Dynamic Partial Reconfiguration (DPR) and dynamic frequency control on FPGAs. The framework is demonstrated on: i) a dynamic pixel processor, ii) a dynamically reconfigurable 1-D digital filtering architecture, and iii) a dynamically reconfigurable 2-D separable digital filtering system. Efficient implementations of the pixel processor are based on the use of look-up tables and local-multiplexes to minimize FPGA resources. For the pixel-processor, different realizations are generated based on the number of input bits, the number of cores, the number of output bits, and the frequency of operation. For each parameters combination, there is a different pixel-processor realization. Pareto-optimal realizations are selected based on measurements of energy per frame, PSNR accuracy, and performance in terms of frames per second. Dynamic EPA/PPA management is demonstrated for a sequential list of real-time constraints by selecting optimal realizations and implementing using DPR and dynamic frequency control. Efficient FPGA implementations for the 1-D and 2-D FIR filters are based on the use a distributed arithmetic technique. Different realizations are generated by varying the number of coefficients, coefficient bitwidth, and output bitwidth. Pareto-optimal realizations are selected in the EPA space. Dynamic EPA management is demonstrated on the application of real-time EPA constraints on a digital video. The results suggest that the general framework can be applied to a variety of digital signal, image, and video processing systems. It is based on the use of offline-processing that is used to determine the Pareto-optimal realizations. Real-time constraints are met by selecting Pareto-optimal realizations pre-loaded in memory that are then implemented efficiently using DPR and/or dynamic frequency control