높은 전류 구동능력을 가지는 SiGe 나노시트 구조의 터널링 전계효과 트랜지스터

학위논문 (박사) -- 서울대학교 대학원 : 공과대학 전기·정보공학부, 2021. 2. 박병국.The development of very-large-scale integration (VLSI) technology has continuously demanded smaller devices to achieve high integration density for faster computing speed or higher capacity. However, in the recent complementary-metal-oxide-semiconductor (CMOS) technology, simple downsizing the dimension of metal-oxide-semiconductor field-effect transistor (MOSFET) no longer guarantees the boosting performance of IC chips. In particular, static power consumption is not reduced while device size is decreasing because voltage scaling is slowed down at some point. The increased off-current due to short-channel effect (SCE) of MOSFET is a representative cause of the difficulty in voltage scaling. To overcome these fundamental limits of MOSFET, many researchers have been looking for the next generation of FET device over the last ten years. Tunnel field-effect transistor (TFET) has been intensively studied for its steep switching characteristics. Nevertheless, the poor current drivability of TFET is the most serious obstacle to become competitive device for MOSFET. In this thesis, TFET with high current drivability in which above-mentioned problem is significantly solved is proposed. Vertically-stacked SiGe nanosheet channels are used to boost carrier injection and gate control. The fabrication technique to form highly-condensed SiGe nanosheets is introduced. TFET is fabricated with MOSFET with the same structure in the CMOS-compatible process. Both technology-computer-aided-design (TCAD) simulation and experimental results are utilized to support and examine the advantages of proposed TFET. From the perspective of the single device, the improvement in switching characteristics and current drivability are quantitatively and qualitatively analyzed. In addition, the device performance is compared to the benchmark of previously reported TFET and co-fabricated MOSFET. Through those processes, the feasibility of SiGe nanosheet TFET is verified. It is revealed that the proposed SiGe nanosheet TFET has notable steeper switching and low leakage in the low drive voltage as an alternative to conventional MOSFET.초고밀도 집적회로 기술의 발전은 고집적도 달성을 통해 단위 칩의 연산 속도 및 용량 향상에 기여할 소형의 소자를 끊임없이 요구하고 있다. 하지만 최신의 상보형 금속-산화막-반도체 (CMOS) 기술에서 금속-산화막-반도체 전계 효과 트랜지스터 (MOSFET) 의 단순한 소형화는 더 이상 집적회로의 성능 향상을 보장해 주지 못하고 있다. 특히 소자의 크기가 줄어드는 반면 정적 전력 소모량은 전압 스케일링의 둔화로 인해 감소되지 않고 있는 상황이다. MOSFET의 짧은 채널 효과로 인해 증가된 누설 전류가 전압 스케일링의 어려움을 주는 대표적 원인으로 꼽힌다. 이러한 근본적인 MOSFET의 한계를 극복하기 위하여 지난 10여년간 새로운 단계의 전계 효과 트랜지스터 소자들이 연구되고 있다. 그 중 터널 전계 효과 트랜지스터(TFET)은 그 특유의 우수한 전원 특성으로 각광받아 집중적으로 연구되고 있다. 많은 연구에도 불구하고, TFET의 부족한 전류 구동 능력은 MOSFET의 대체재로 자리매김하는 데 가장 큰 문제점이 되고 있다. 본 학위논문에서는 상기된 문제점을 해결할 수 있는 우수한 전류 구동 능력을 가진 TFET이 제안되었다. 반송자 유입과 게이트 컨트롤을 향상시킬 수 있는 수직 적층된 실리콘저마늄(SiGe) 나노시트 채널이 사용되었다. 또한, 제안된 TFET은 CMOS 기반 공정을 활용하여 MOSFET과 함께 제작되었다. 테크놀로지 컴퓨터 지원 설계(TCAD) 시뮬레이션과 실제 측정 결과를 활용하여 제안된 소자의 우수성을 검증하였다. 단위 CMOS 소자의 관점에서, 전원 특성과 전류 구동 능력의 향상을 정량적, 정성적 방법으로 분석하였다. 그리고, 제작된 소자의 성능을 기존 제작 및 보고된 TFET 및 함께 제작된 MOSSFET과 비교하였다. 이러한 과정을 통해, 실리콘저마늄 나노시트 TFET의 활용 가능성이 입증되었다. 제안된 실리콘저마늄 나노시트 소자는 주목할 만한 전원 특성을 가졌고 저전압 구동 환경에서 한층 더 낮은 누설 전류를 가짐으로써 향후 MOSFET을 대체할만한 충분한 가능성을 보여주었다.Chapter 1 Introduction 1 1.1. Power Crisis of Conventional CMOS Technology 1 1.2. Tunnel Field-Effect Transistor (TFET) 6 1.3. Feasibility and Challenges of TFET 9 1.4. Scope of Thesis 11 Chapter 2 Device Characterization 13 2.1. SiGe Nanosheet TFET 13 2.2. Device Concept 15 2.3. Calibration Procedure for TCAD simulation 17 2.4. Device Verification with TCAD simulation 21 Chapter 3 Device Fabrication 31 3.1. Fabrication Process Flow 31 3.2. Key Processes for SiGe Nanosheet TFET 33 3.2.1. Key Process 1 : SiGe Nanosheet Formation 34 3.2.2. Key Process 2 : Source/Drain Implantation 41 3.2.3. Key Process 3 : High-κ/Metal gate Formation 43 Chapter 4 Results and Discussion 53 4.1. Measurement Results 53 4.2. Analysis of Device Characteristics 56 4.2.1. Improved Factors to Performance in SiGe Nanosheet TFET 56 4.2.2. Performance Comparison with SiGe Nanosheet MOSFET 62 4.3. Performance Evaluation through Benchmarks 64 4.4. Optimization Plan for SiGe nanosheet TFET 66 4.4.1. Improvement of Quality of Gate Dielectric 66 4.4.2. Optimization of Doping Junction at Source 67 Chapter 5 Conclusion 71 Bibliography 73 Abstract in Korean 81 List of Publications 83Docto

InGaAs/GaAsSb type-two heterojunction vertical tunnel-FETs

Thesis (S.M.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2013.Cataloged from PDF version of thesis.Includes bibliographical references (pages 59-62).The supply voltage (VDD) scaling of conventional CMOS technology is approaching its limit due to the physical limit of 60 mV/dec subthreshold swing (SS) at room temperature and the requirement for controlled leakage current. In order to continue VDD scaling for low power applications, novel device structures with steep SS have been proposed. Tunnel-FETs (TFETs) are among the most attractive device structure due to their compatibility with conventional CMOS technology and the potential for outstanding VDD scalability. Heterostructure vertical TFETs with enhanced gate modulation promise significantly improved electrostatic control and drive current relative to lateral tunneling designs. In this thesis, vertical TFETs based on InGaAs/GaAsSb heterostructure are investigated in terms of design, fabrication and electrical characterization. Ino.53Gao.47As/ GaAso.5Sb0.5 heterostructure vertical TFETs are fabricated with an airbridge structure, designed to prevent parasitic tunneling path in the device, with a two-step highly selective undercut process. Electrical measurement of the devices with various gate areas demonstrates area-dependent tunneling current. The Ino.53Gao.47As/ GaAs0 .5 Sb. 5 vertical TFETs with HfO2 high-k gate dielectric (EOT ~ 1.3 nm) exhibit minimum sub-threshold swings of 140 and 58 mV/dec at 300 and 150 K respectively, with an ON-current density of 0.5 [mu]A/[mu]m2 at VDD = 0.5 V at 300 K. A physical model of TFET operation in the ON-state is proposed based on temperature dependent measurements, which reveal a current barrier due to an ungated region near the drain. Simulations illustrate that the gate-to-drain distance must be scaled to eliminate this barrier. In diode-mode operation, outstanding backward diode performance is demonstrated in this system for the first time, with gate-tunable curvature coefficient of 30 V1 near VDS= 0 V. These results indicate the potential of vertical TFETs in hybrid IC applications.by Tao Yu.S.M

High-Performance Silicon Nanowire Electronics

This thesis explores 10-nm wide Si nanowire (SiNW) field-effect transistors (FETs) for logic applications via the fabrication and testing of SiNW-based ring oscillators. Both SiNW surface treatments and dielectric annealing are reported for producing SiNW FETs that exhibit high performance in terms of large on/off-state current ratio (~108), low drain-induced barrier lowering (~30 mV), high carrier mobilities (~269 cm2/V•s), and low subthreshold swing (~80 mV/dec). The performance of inverter and ring-oscillator circuits fabricated from these nanowire FETs is explored as well. The inverter demonstrates the highest voltage gain (~148) reported for a SiNW-based NOT gate, and the ring oscillator exhibits near rail-to-rail oscillation centered at 13.4 MHz. The static and dynamic characteristics of these NW devices indicate that these SiNW-based FET circuits are excellent candidates for various high-performance nanoelectronic applications. A set of novel charge-trap non-volatile memory devices based on high-performance SiNW FETs are well investigated. These memory devices integrate Fe2O3 quantum dots (FeO QDs) as charge storage elements. A template-assisted assembly technique is used to align FeO QDs into a close-packed, ordered matrix within the trenches that separate highly aligned SiNWs, and thus store injected charges. A Fowler-Nordheim tunneling mechanism describes both the program and erase operations. The memory prototype demonstrates promising characteristics in terms of large threshold voltage shift (~1.3 V) and long data retention time (~3 × 106 s), and also allows for key components to be systematically varied. For example, varying the size of the QDs indicates that larger diameter QDs exhibit a larger memory window, suggesting the QD charging energy plays an important role in the carrier transport. The device temperature characteristics reveal an optimal window for device performance between 275K and 350K. The flexibility of integrating the charge-trap memory devices with the SiNW logic devices offers a low-cost embedded non-volatile memory solution. A building block for a SiNW-based field-programmable gate array (FPGA) is proposed in the future work.</p

Design, Modeling and Analysis of Non-classical Field Effect Transistors

Transistor scaling following per Moore\u27s Law slows down its pace when entering into nanometer regime where short channel effects (SCEs), including threshold voltage fluctuation, increased leakage current and mobility degradation, become pronounced in the traditional planar silicon MOSFET. In addition, as the demand of diversified functionalities rises, conventional silicon technologies cannot satisfy all non-digital applications requirements because of restrictions that stem from the fundamental material properties. Therefore, novel device materials and structures are desirable to fuel further evolution of semiconductor technologies. In this dissertation, I have proposed innovative device structures and addressed design considerations of those non-classical field effect transistors for digital, analog/RF and power applications with projected benefits. Considering device process difficulties and the dramatic fabrication cost, application-oriented device design and optimization are performed through device physics analysis and TCAD modeling methodology to develop design guidelines utilizing transistor\u27s improved characteristics toward application-specific circuit performance enhancement. Results support proposed device design methodologies that will allow development of novel transistors capable of overcoming limitation of planar nanoscale MOSFETs. In this work, both silicon and III-V compound devices are designed, optimized and characterized for digital and non-digital applications through calibrated 2-D and 3-D TCAD simulation. For digital functionalities, silicon and InGaAs MOSFETs have been investigated. Optimized 3-D silicon-on-insulator (SOI) and body-on-insulator (BOI) FinFETs are simulated to demonstrate their impact on the performance of volatile memory SRAM module with consideration of self-heating effects. Comprehensive simulation results suggest that the current drivability degradation due to increased device temperature is modest for both devices and corresponding digital circuits. However, SOI FinFET is recommended for the design of low voltage operation digital modules because of its faster AC response and better SCEs management than the BOI structure. The FinFET concept is also applied to the non-volatile memory cell at 22 nm technology node for low voltage operation with suppressed SCEs. In addition to the silicon technology, our TCAD estimation based on upper projections show that the InGaAs FinFET, with superior mobility and improved interface conditions, achieve tremendous drive current boost and aggressively suppressed SCEs and thereby a strong contender for low-power high-performance applications over the silicon counterpart. For non-digital functionalities, multi-fin FETs and GaN HEMT have been studied. Mixed-mode simulations along with developed optimization guidelines establish the realistic application potential of underlap design of silicon multi-Fin FETs for analog/RF operation. The device with underlap design shows compromised current drivability but improve analog intrinsic gain and high frequency performance. To investigate the potential of the novel N-polar GaN material, for the first time, I have provided calibrated TCAD modeling of E-mode N-polar GaN single-channel HEMT. In this work, I have also proposed a novel E-mode dual-channel hybrid MIS-HEMT showing greatly enhanced current carrying capability. The impact of GaN layer scaling has been investigated through extensive TCAD simulations and demonstrated techniques for device optimization

Proceedings of the Cold Electronics Workshop

The benefits and problems of the use of cold semiconductor electronics and the research and development effort required to bring cold electronics into more widespread use were examined

Miniaturized Transistors, Volume II

In this book, we aim to address the ever-advancing progress in microelectronic device scaling. Complementary Metal-Oxide-Semiconductor (CMOS) devices continue to endure miniaturization, irrespective of the seeming physical limitations, helped by advancing fabrication techniques. We observe that miniaturization does not always refer to the latest technology node for digital transistors. Rather, by applying novel materials and device geometries, a significant reduction in the size of microelectronic devices for a broad set of applications can be achieved. The achievements made in the scaling of devices for applications beyond digital logic (e.g., high power, optoelectronics, and sensors) are taking the forefront in microelectronic miniaturization. Furthermore, all these achievements are assisted by improvements in the simulation and modeling of the involved materials and device structures. In particular, process and device technology computer-aided design (TCAD) has become indispensable in the design cycle of novel devices and technologies. It is our sincere hope that the results provided in this Special Issue prove useful to scientists and engineers who find themselves at the forefront of this rapidly evolving and broadening field. Now, more than ever, it is essential to look for solutions to find the next disrupting technologies which will allow for transistor miniaturization well beyond silicon’s physical limits and the current state-of-the-art. This requires a broad attack, including studies of novel and innovative designs as well as emerging materials which are becoming more application-specific than ever before

Tunnel Field-Effect Transistor: Impact of the Asymmetric and Symmetric Ambipolarity on Fault and Performance in Digital Circuits

Tunnel Field-Effect Transistors (TFETs) have been considered one of the most promising technologies to complement or replace CMOS for ultra-low-power applications, thanks to their subthreshold slope below the well-known limit of 60 mV/dec at room temperature holding for the MOSFET technologies. Nevertheless, TFET technology still suffers of ambipolar conduction, limiting its applicability in digital systems. In this work, we analyze through SPICE simulations, the impact of the symmetric and asymmetric ambipolarity in failure and power consumption for TFET-based complementary logic circuits. Our results clarify the circuit-level effects induced by the ambipolarity feature, demonstrating that it affects the correct functioning of logic gates and strongly impacts power consumption. We believe that our outcomes motivate further research towards technological solutions for ambipolarity suppression in TFET technology for near-future ultra-low-power application

Modeling Of Two Dimensional Graphene And Non-graphene Material Based Tunnel Field Effect Transistors For Integrated Circuit Design

The Moore’s law of scaling of metal oxide semiconductor field effect transistor (MOSFET) had been a driving force toward the unprecedented advancement in development of integrated circuit over the last five decades. As the technology scales down to 7 nm node and below following the Moore’s law, conventional MOSFETs are becoming more vulnerable to extremely high off-state leakage current exhibiting a tremendous amount of standby power dissipation. Moreover, the fundamental physical limit of MOSFET of 60 mV/decade subthreshold slope exacerbates the situation further requiring current transport mechanism other than drift and diffusion for the operation of transistors. One way to limit such unrestrained amount of power dissipation is to explore novel materials with superior thermal and electrical properties compared to traditional bulk materials. On the other hand, energy efficient steep subthreshold slope devices are the other possible alternatives to conventional MOSFET based on emerging novel materials. This dissertation addresses the potential of both advanced materials and devices for development of next generation energy efficient integrated circuits. Among the different steep subthreshold slope devices, tunnel field effect transistor (TFET) has been considered as a promising candidate after MOSFET. A superior gate control on source-channel band-to-band tunneling providing subthreshold slopes well below than 60 mV/decade. With the emergence of atomically thin two-dimensional (2D) materials, interest in the design of TFET based on such novel 2D materials has also grown significantly. Graphene being the first and the most studied among 2D materials with exotic electronic and thermal properties. This dissertation primarily considers current transport modeling of graphene based tunnel devices from transport phenomena to energy efficient integrated circuit design. Three current transport models: semi-classical, semi-quantum and numerical simulations are described for the modeling of graphene nanoribbon tunnel field effect transistor (GNR TFET) where the semi-classical model is in close agreement with the quantum transport simulation. Moreover, the models produced are also extended for integrated circuit design using Verilog-A hardware description language for logic design. In order to overcome the challenges associated with the band gap engineering for making graphene transistor for logic operation, the promise of graphene based interlayer tunneling transistors are discussed along with their existing fundamental physical limitation of subthreshold slope. It has been found that such interlayer tunnel transistor has very poor electrostatic gate control on drain current. It gives subthreshold slope greater than the thermionic limit of 60 mV/decade at room temperature. In order to resolve such limitation of interlayer tunneling transistors, a new type of transistor named “junctionless tunnel effect transistor (JTET)” has been invented and modeled for the first time considering graphene-boron nitride (BN)-graphene and molybdenum disulfide (MoS2)-boron nitride (BN) heterostructures, where the interlayer tunneling mechanism controls the source-drain ballistic transport instead of depleting carriers in the channel. Steep subthreshold slope, low power and high frequency THz operation are few of the promising features studied for such graphene and MoS2 JTETs. From current transport modeling to energy efficient integrated circuit design using Verilog-A has been carried out for these new devices as well. Thus, findings in this dissertation would suggest the exciting opportunity of a new class of next generation energy efficient material based transistors as switches

Vertical Heterostructure III-V MOSFETs for CMOS, RF and Memory Applications

This thesis focuses mainly on the co-integration of vertical nanowiren-type InAs and p-type GaSb MOSFETs on Si (Paper I & II), whereMOVPE grown vertical InAs-GaSb heterostructure nanowires areused for realizing monolithically integrated and co-processed all-III-V CMOS.Utilizing a bottom-up approach based on MOVPE grown nanowires enablesdesign flexibilities, such as in-situ doping and heterostructure formation,which serves to reduce the amount of mask steps during fabrication. By refiningthe fabrication techniques, using a self-aligned gate-last process, scaled10-20 nm diameters are achieved for balanced drive currents at Ion ∼ 100μA/μm, considering Ioff at 100 nA/μm (VDD = 0.5 V). This is enabledby greatly improved p-type MOSFET performance reaching a maximumtransconductance of 260 μA/μm at VDS = 0.5 V. Lowered power dissipationfor CMOS circuits requires good threshold voltage VT matching of the n- andp-type device, which is also demonstrated for basic inverter circuits. Thevarious effects contributing to VT-shifts are also studied in detail focusing onthe InAs channel devices (with highest transconductance of 2.6 mA/μm), byusing Electron Holography and a novel gate position variation method (PaperV).The advancements in all-III-V CMOS integration spawned individual studiesinto the strengths of the n- and p-type III-V devices, respectively. Traditionallymaterials such as InAs and InGaAs provide excellent electrontransport properties, therefore they are frequently used in devices for highfrequency RF applications. In contrast, the III-V p-type alternatives have beenlacking performance mostly due to the difficult oxidation properties of Sb-based materials. Therefore, a study of the GaSb properties, in a MOSFETchannel, was designed and enabled by new manufacturing techniques, whichallowed gate-length scaling from 40 to 140 nm for p-type Sb-based MOSFETs(Paper III). The new fabrication method allowed for integration of deviceswith symmetrical contacts as compared to previous work which relied on atunnel-contact at the source-side. By modelling based on measured data fieldeffecthole mobility of 70 cm2/Vs was calculated, well in line with previouslyreported studies on GaSb nanowires. The oxidation properties of the GaSbgate-stack was further characterized by XPS, where high intensities of xraysare achieved using a synchrotron source allowed for characterization ofnanowires (Paper VI). Here, in-situ H2-plasma treatment, in parallel with XPSmeasurements, enabled a study of the time-dependence during full removalof GaSb native oxides.The last focus of the thesis was building on the existing strengths of verticalheterostructure III-V n-type (InAs-InGaAs graded channel) devices. Typically,these devices demonstrate high-current densities (gm >3 mS/μm) and excellentmodulation properties (off-state current down to 1 nA/μm). However,minimizing the parasitic capacitances, due to various overlaps originatingfrom a low access-resistance design, has proven difficult. Therefore, newmethods for spacers in both the vertical and planar directions was developedand studied in detail. The new fabrication methods including sidewall spacersachieved gate-drain capacitance CGD levels close to 0.2 fF/μm, which isthe established limit by optimized high-speed devices. The vertical spacertechnology, using SiO2 on the nanowire sidewalls, is further improved inthis thesis which enables new co-integration schemes for memory arrays.Namely, the refined sidewall spacer method is used to realize selective recessetching of the channel and reduced capacitance for large array memoryselector devices (InAs channel) vertically integrated with Resistive RandomAccess Memory (RRAM) memristors. (Paper IV) The fabricated 1-transistor-1-memristor (1T1R) demonstrator cell shows excellent endurance and retentionfor the RRAM by maintaining constant ratio of the high and low resistive state(HRS/LRS) after 106 switching cycles

Vertical III-V Nanowire Transistors for Low-Power Logic and Reconfigurable Applications

With rapid increase in energy consumption of electronics used in our daily life, the building blocks — transistors — need to work in a way that has high energy efficiency and functional density to meet the demand of further scaling. III-V channel combined with vertical nanowire gate-all-around (GAA) device architecture is a promising alternative to conventional Si transistors due to its excellent electrical properties in the channel and electrostatic control across the gate oxide in addition to reduced footprint. Based on this platform, two major objectives of this thesis are included: 1) to improve the performance of III-V p-type metal-oxide-semiconductor field-effect transistors (MOSFETs) and tunnel FETs (TFETs) for low-power digital applications; 2) to integrate HfO2-based ferroelectric gate onto III-V FETs (FeFETs) and TFETs (ferro-TFETs) to enable reconfigurable operation for high functional density.The key bottleneck for all-III-V CMOS is its p-type MOSFETs (p-FETs) which are mainly made of GaSb or InGaSb. Rich surface states of III-Sb materials not only lead to decreased effective channel mobility due to more scattering, but also deteriorate the electrostatics. In this thesis, several approaches to improve p-FET performance have been explored. One strategy is to enhance the hole mobility by introducing compressive strain into III-Sb channel. For the first time, a high and uniform compressive strain near 1% along the transport direction has been achieved in downscaled GaSb nanowires by growing and engineering GaSb-GaAsSb core-shell structure, aiming for potential hole mobility enhancement. In addition, surface passivation using digital etch has been developed to improve the electrostatics with subthreshold swing (SS) down to 107 mV/dec. Moreover, the on-state performance including on-current (Ion) and transconductance (gm) have been enhanced by ∼50% using annealing with H2-based forming gas. Lastly, a novel p-FET structure with (In)GaAsSb channel has been developed and further improved off-state performance with SS = 71 mV/dec, which is the lowest value among all reported III-V p-FETs.Despite subthermionic operation, TFETs usually suffer from low drive current as well as the current operating below 60 mV/dec (I60). The second focus of this thesis is to fine-tune the InAs/(In)GaAsSb heterostructure tunnel junction and the doping in the source segment during epitaxy. As a result, a substantially increased I60 (>1 µA/µm) and Ion up to 40 µA/µm at source-drain bias of 0.5 V have been achieved, reaching a record compared to other reported TFETs.Finally, emerging ferroelectric oxide based on Zr-doped HfO2 (HZO) has been successfully integrated onto III-V vertical nanowire transistors to form FeFETs and ferro-TFETs with GAA architecture. The corresponding electrical performance and reliability have been carefully characterized with both DC and pulsed I-V measurements. The unique band-to-band tunneling in InAs/(In)GaAsSb/GaSb heterostructure TFET creates an ultrashort effective channel, leading to detection of localized potential variation induced by single domains and defects in nanoscale ferroelectric HZO without physical gate-length scaling. By introducing gate/source overlap structure in the ferro-TFET, non-volatile reconfigurable signal modulation with multiple modes including signal transmission, phase shift, frequency doubling, and mixing has been achieved in a single device with low drive voltage and only ∼0.01 µm2 footprint, thus increasing both functional density andenergy efficiency