A high speed Tri-Vision system for automotive applications

Purpose: Cameras are excellent ways of non-invasively monitoring the interior and exterior of vehicles. In particular, high speed stereovision and multivision systems are important for transport applications such as driver eye tracking or collision avoidance. This paper addresses the synchronisation problem which arises when multivision camera systems are used to capture the high speed motion common in such applications. Methods: An experimental, high-speed tri-vision camera system intended for real-time driver eye-blink and saccade measurement was designed, developed, implemented and tested using prototype, ultra-high dynamic range, automotive-grade image sensors specifically developed by E2V (formerly Atmel) Grenoble SA as part of the European FP6 project – sensation (advanced sensor development for attention stress, vigilance and sleep/wakefulness monitoring). Results : The developed system can sustain frame rates of 59.8 Hz at the full stereovision resolution of 1280 × 480 but this can reach 750 Hz when a 10 k pixel Region of Interest (ROI) is used, with a maximum global shutter speed of 1/48000 s and a shutter efficiency of 99.7%. The data can be reliably transmitted uncompressed over standard copper Camera-Link® cables over 5 metres. The synchronisation error between the left and right stereo images is less than 100 ps and this has been verified both electrically and optically. Synchronisation is automatically established at boot-up and maintained during resolution changes. A third camera in the set can be configured independently. The dynamic range of the 10bit sensors exceeds 123 dB with a spectral sensitivity extending well into the infra-red range. Conclusion: The system was subjected to a comprehensive testing protocol, which confirms that the salient requirements for the driver monitoring application are adequately met and in some respects, exceeded. The synchronisation technique presented may also benefit several other automotive stereovision applications including near and far-field obstacle detection and collision avoidance, road condition monitoring and others.Partially funded by the EU FP6 through the IST-507231 SENSATION project.peer-reviewe

Adaptive beam control and analysis in fluorescence microscopy

This thesis details three novel advances in instrumentation that are each related to performance improvement in wide-field visible-spectrum imaging systems. In each case our solution concerns the assessment and improvement of optical imaging quality. The three instruments are as follows: The first is a portable transmission microscope which is able to correct for artificially induced aberrations using adaptive optics (AO). The specimens and the method of introducing aberrations into the optical system can be altered to simulate the performance of AO-correction in both astronomical and biological imaging. We present the design and construction of the system alongside before-and-after AO-correction images for simulated astronomical and biological images. The second instrument is a miniature endoscope camera sensor we re-purposed for use as a quantitative beam analysis probe using a custom high dynamic range (HDR) imaging and reconstruction procedure. This allowed us to produce quantitative flux maps of the illumination beam intensity profile within several operational fluorescence microscope systems. The third and final project in this thesis was concerned with an adaptive modification to the light sheet illumination beam used in light sheet microscopy, specifically for a single plane illumination microscope (SPIM), embracing the trade-off between the thickness of the light sheet and its extent across the detection field-of-view. The focal region of the beam was made as small as possible and then matched to the shape of curved features within a biological specimen by using a spatial light modulator (SLM) to alter the light sheet focal length throughout the vertical span of the sheet. We used the HDR beam profiling camera probe mentioned earlier to assess the focal shape and quality of the beam. The resulting illumination beam may in the future be used in a modified SPIM system to produce fluorescence microscope images with enhanced optical sectioning of specific curved features

A Method to Achieve High Dynamic Range in a CMOS Image Sensor Using Interleaved Row Readout

©2022 The Author(s). This work is licensed under a Creative Commons Attribution 4.0 License. For more information, see https://creativecommons.org/licenses/by/4.0/We present a readout scheme for CMOS image sensors that can be used to achieve arbitrarily high dynamic range (HDR) in principle. The linear full well capacity (LFWC) in high signal regions was extended 50 times from 20 to 984 ke − via an interlaced row-wise readout order, while the noise floor remained unchanged in low signal regions, resulting in a 34-dB increase in DR. The peak signal-to-noise ratio (PSNR) is increased in a continuous fashion from 43 to 60 dB. This was achieved by summing user-selected rows that were read out multiple times. Centroiding uncertainties were lowered when template-fitting a projected pattern, compared to the standard readout scheme. Example applications are aimed at scientific imaging due to the linearity and PSNR increase.Peer reviewe

A Comparative Evaluation of the Detection and Tracking Capability Between Novel Event-Based and Conventional Frame-Based Sensors

Traditional frame-based technology continues to suffer from motion blur, low dynamic range, speed limitations and high data storage requirements. Event-based sensors offer a potential solution to these challenges. This research centers around a comparative assessment of frame and event-based object detection and tracking. A basic frame-based algorithm is used to compare against two different event-based algorithms. First event-based pseudo-frames were parsed through standard frame-based algorithms and secondly, target tracks were constructed directly from filtered events. The findings show there is significant value in pursuing the technology further

Propuesta de arquitectura y circuitos para la mejora del rango dinámico de sistemas de visión en un chip diseñados en tecnologías CMOS profundamente submicrométrica

El trabajo presentado en esta tesis trata de proponer nuevas técnicas para la expansión del rango dinámico en sensores electrónicos de imagen. En este caso, hemos dirigido nuestros estudios hacia la posibilidad de proveer dicha funcionalidad en un solo chip. Esto es, sin necesitar ningún soporte externo de hardware o software, formando un tipo de sistema denominado Sistema de Visión en un Chip (VSoC). El rango dinámico de los sensores electrónicos de imagen se define como el cociente entre la máxima y la mínima iluminación medible. Para mejorar este factor surgen dos opciones. La primera, reducir la mínima luz medible mediante la disminución del ruido en el sensor de imagen. La segunda, incrementar la máxima luz medible mediante la extensión del límite de saturación del sensor. Cronológicamente, nuestra primera opción para mejorar el rango dinámico se basó en reducir el ruido. Varias opciones se pueden tomar para mejorar la figura de mérito de ruido del sistema: reducir el ruido usando una tecnología CIS o usar circuitos dedicados, tales como calibración o auto cero. Sin embargo, el uso de técnicas de circuitos implica limitaciones, las cuales sólo pueden ser resueltas mediante el uso de tecnologías no estándar que están especialmente diseñadas para este propósito. La tecnología CIS utilizada está dirigida a la mejora de la calidad y las posibilidades del proceso de fotosensado, tales como sensibilidad, ruido, permitir imagen a color, etcétera. Para estudiar las características de la tecnología en más detalle, se diseñó un chip de test, lo cual permite extraer las mejores opciones para futuros píxeles. No obstante, a pesar de un satisfactorio comportamiento general, las medidas referentes al rango dinámico indicaron que la mejora de este mediante sólo tecnología CIS es muy limitada. Es decir, la mejora de la corriente oscura del sensor no es suficiente para nuestro propósito. Para una mayor mejora del rango dinámico se deben incluir circuitos dentro del píxel. No obstante, las tecnologías CIS usualmente no permiten nada más que transistores NMOS al lado del fotosensor, lo cual implica una seria restricción en el circuito a usar. Como resultado, el diseño de un sensor de imagen con mejora del rango dinámico en tecnologías CIS fue desestimado en favor del uso de una tecnología estándar, la cual da más flexibilidad al diseño del píxel. En tecnologías estándar, es posible introducir una alta funcionalidad usando circuitos dentro del píxel, lo cual permite técnicas avanzadas para extender el límite de saturación de los sensores de imagen. Para este objetivo surgen dos opciones: adquisición lineal o compresiva. Si se realiza una adquisición lineal, se generarán una gran cantidad de datos por cada píxel. Como ejemplo, si el rango dinámico de la escena es de 120dB al menos se necesitarían 20-bits/píxel, log2(10120/20)=19.93, para la representación binaria de este rango dinámico. Esto necesitaría de amplios recursos para procesar esta gran cantidad de datos, y un gran ancho de banda para moverlos al circuito de procesamiento. Para evitar estos problemas, los sensores de imagen de alto rango dinámico usualmente optan por utilizar una adquisición compresiva de la luz. Por lo tanto, esto implica dos tareas a realizar: la captura y la compresión de la imagen. La captura de la imagen se realiza a nivel de píxel, en el dispositivo fotosensor, mientras que la compresión de la imagen puede ser realizada a nivel de píxel, de sistema, o mediante postprocesado externo. Usando el postprocesado, existe un campo de investigación que estudia la compresión de escenas de alto rango dinámico mientras se mantienen los detalles, produciendo un resultado apropiado para la percepción humana en monitores convencionales de bajo rango dinámico. Esto se denomina Mapeo de Tonos (Tone Mapping) y usualmente emplea solo 8-bits/píxel para las representaciones de imágenes, ya que éste es el estándar para las imágenes de bajo rango dinámico. Los píxeles de adquisición compresiva, por su parte, realizan una compresión que no es dependiente de la escena de alto rango dinámico a capturar, lo cual implica una baja compresión o pérdida de detalles y contraste. Para evitar estas desventajas, en este trabajo, se presenta un píxel de adquisición compresiva que aplica una técnica de mapeo de tonos que permite la captura de imágenes ya comprimidas de una forma optimizada para mantener los detalles y el contraste, produciendo una cantidad muy reducida de datos. Las técnicas de mapeo de tonos ejecutan normalmente postprocesamiento mediante software en un ordenador sobre imágenes capturadas sin compresión, las cuales contienen una gran cantidad de datos. Estas técnicas han pertenecido tradicionalmente al campo de los gráficos por ordenador debido a la gran cantidad de esfuerzo computacional que requieren. Sin embargo, hemos desarrollado un nuevo algoritmo de mapeo de tonos especialmente adaptado para aprovechar los circuitos dentro del píxel y que requiere un reducido esfuerzo de computación fuera de la matriz de píxeles, lo cual permite el desarrollo de un sistema de visión en un solo chip. El nuevo algoritmo de mapeo de tonos, el cual es un concepto matemático que puede ser simulado mediante software, se ha implementado también en un chip. Sin embargo, para esta implementación hardware en un chip son necesarias algunas adaptaciones y técnicas avanzadas de diseño, que constituyen en sí mismas otra de las contribuciones de este trabajo. Más aún, debido a la nueva funcionalidad, se han desarrollado modificaciones de los típicos métodos a usar para la caracterización y captura de imágenes

Smart Sensor Networks For Sensor-Neural Interface

One in every fifty Americans suffers from paralysis, and approximately 23% of paralysis cases are caused by spinal cord injury. To help the spinal cord injured gain functionality of their paralyzed or lost body parts, a sensor-neural-actuator system is commonly used. The system includes: 1) sensor nodes, 2) a central control unit, 3) the neural-computer interface and 4) actuators. This thesis focuses on a sensor-neural interface and presents the research related to circuits for the sensor-neural interface. In Chapter 2, three sensor designs are discussed, including a compressive sampling image sensor, an optical force sensor and a passive scattering force sensor. Chapter 3 discusses the design of the analog front-end circuit for the wireless sensor network system. A low-noise low-power analog front-end circuit in 0.5μm CMOS technology, a 12-bit 1MS/s successive approximation register (SAR) analog-to-digital converter (ADC) in 0.18μm CMOS process and a 6-bit asynchronous level-crossing ADC realized in 0.18μm CMOS process are presented. Chapter 4 shows the design of a low-power impulse-radio ultra-wide-band (IR-UWB) transceiver (TRx) that operates at a data rate of up to 10Mbps, with a power consumption of 4.9pJ/bit transmitted for the transmitter and 1.12nJ/bit received for the receiver. In Chapter 5, a wireless fully event-driven electrogoniometer is presented. The electrogoniometer is implemented using a pair of ultra-wide band (UWB) wireless smart sensor nodes interfacing with low power 3-axis accelerometers. The two smart sensor nodes are configured into a master node and a slave node, respectively. An experimental scenario data analysis shows higher than 90% reduction of the total data throughput using the proposed fully event-driven electrogoniometer to measure joint angle movements when compared with a synchronous Nyquist-rate sampling system. The main contribution of this thesis includes: 1) the sensor designs that emphasize power efficiency and data throughput efficiency; 2) the fully event-driven wireless sensor network system design that minimizes data throughput and optimizes power consumption

Analysis and design of a wide dynamic range pulse-frequency modulation CMOS image sensor

Complementary Metal-Oxide Semiconductor (CMOS) image sensor is the dominant electronic imaging device in many application fields, including the mobile or portable devices, teleconference cameras, surveillance and medical imaging sensors. Wide dynamic range (WDR) imaging is of interest particular, demonstrating a large-contrast imaging range of the sensor. As of today, different approaches have been presented to provide solutions for this purpose, but there exists various trade-offs among these designs, which limit the number of applications. A pulse-frequency modulation (PFM) pixel offers the possibility to outperform existing designs in WDR imaging applications, however issues such as uniformity and cost have to be carefully handled to make it practical for different purposes. In addition, a complete evaluation of the sensor performance has to be executed prior to fabrication in silicon technology. A thorough investigation of WDR image sensor based on the PFM pixel is performed in this thesis. Starting with the analysis, modeling, and measurements of a PFM pixel, the details of every particular circuit operation are presented. The causes of dynamic range (DR) limitations and signal nonlinearity are identified, and noise measurement is also performed, to guide future design strategies. We present the design of an innovative double-delta compensating (DDC) technique which increases the sensor uniformity as well as DR. This technique achieves performance optimization of the PFM pixel with a minimal cost an improved linearity, and is carefully simulated to demonstrate its feasibility. A quad-sampling technique is also presented with the cooperation of pixel and column circuits to generate a WDR image sensor with a reduced cost for the pixel. This method, which is verified through the field-programmable gate array (FPGA) implementation, saves considerable area in the pixel and employs the maximal DR that a PFM pixel provides. A complete WDR image sensor structure is proposed to evaluate the performance and feasibility of fabrication in silicon technology. The plans of future work and possible improvements are also presented

From Lab Testing to Science: Applying SAPHIRA HgCdTe L-APD Detectors to Adaptive Optics.

Ph.D. Thesis. University of Hawaiʻi at Mānoa 2018