Very-Large-Scale-Integration Circuit Techniques in Internet-of-Things Applications

Heading towards the era of Internet-of-things (IoT) means both opportunity and challenge for the circuit-design community. In a system where billions of devices are equipped with the ability to sense, compute, communicate with each other and perform tasks in a coordinated manner, security and power management are among the most critical challenges. Physically unclonable function (PUF) emerges as an important security primitive in hardware-security applications; it provides an object-specific physical identifier hidden within the intrinsic device variations, which is hard to expose and reproduce by adversaries. Yet, designing a compact PUF robust to noise, temperature and voltage remains a challenge. This thesis presents a novel PUF design approach based on a pair of ultra-compact analog circuits whose output is proportional to absolute temperature. The proposed approach is demonstrated through two works: (1) an ultra-compact and robust PUF based on voltage-compensated proportional-to-absolute-temperature voltage generators that occupies 8.3× less area than the previous work with the similar robustness and twice the robustness of the previously most compact PUF design and (2) a technique to transform a 6T-SRAM array into a robust analog PUF with minimal overhead. In this work, similar circuit topology is used to transform a preexisting on-chip SRAM into a PUF, which further reduces the area in (1) with no robustness penalty. In this thesis, we also explore techniques for power management circuit design. Energy harvesting is an essential functionality in an IoT sensor node, where battery replacement is cost-prohibitive or impractical. Yet, existing energy-harvesting power management units (EH PMU) suffer from efficiency loss in the two-step voltage conversion: harvester-to-battery and battery-to-load. We propose an EH PMU architecture with hybrid energy storage, where a capacitor is introduced in addition to the battery to serve as an intermediate energy buffer to minimize the battery involvement in the system energy flow. Test-case measurements show as much as a 2.2× improvement in the end-to-end energy efficiency. In contrast, with the drastically reduced power consumption of IoT nodes that operates in the sub-threshold regime, adaptive dynamic voltage scaling (DVS) for supply-voltage margin removal, fully on-chip integration and high power conversion efficiency (PCE) are required in PMU designs. We present a PMU–load co-design based on a fully integrated switched-capacitor DC-DC converter (SC-DC) and hybrid error/replica-based regulation for a fully digital PMU control. The PMU is integrated with a neural spike processor (NSP) that achieves a record-low power consumption of 0.61 µW for 96 channels. A tunable replica circuit is added to assist the error regulation and prevent loss of regulation. With automatic energy-robustness co-optimization, the PMU can set the SC-DC’s optimal conversion ratio and switching frequency. The PMU achieves a PCE of 77.7% (72.2%) at VIN = 0.6 V (1 V) and at the NSP’s margin-free operating point

Designing Novel Hardware Security Primitives for Smart Computing Devices

Smart computing devices are miniaturized electronics devices that can sense their surroundings, communicate, and share information autonomously with other devices to work cohesively. Smart devices have played a major role in improving quality of the life and boosting the global economy. They are ubiquitously present, smart home, smart city, smart girds, industry, healthcare, controlling the hazardous environment, and military, etc. However, we have witnessed an exponential rise in potential threat vectors and physical attacks in recent years. The conventional software-based security approaches are not suitable in the smart computing device, therefore, hardware-enabled security solutions have emerged as an attractive choice. Developing hardware security primitives, such as True Random Number Generator (TRNG) and Physically Unclonable Function (PUF) from electrical properties of the sensor could be a novel research direction. Secondly, the Lightweight Cryptographic (LWC) ciphers used in smart computing devices are found vulnerable against Correlation Power Analysis (CPA) attack. The CPA performs statistical analysis of the power consumption of the cryptographic core and reveals the encryption key. The countermeasure against CPA results in an increase in energy consumption, therefore, they are not suitable for battery operated smart computing devices. The primary goal of this dissertation is to develop novel hardware security primitives from existing sensors and energy-efficient LWC circuit implementation with CPA resilience. To achieve these. we focus on developing TRNG and PUF from existing photoresistor and photovoltaic solar cell sensors in smart devices Further, we explored energy recovery computing (also known as adiabatic computing) circuit design technique that reduces the energy consumption compared to baseline CMOS logic design and same time increasing CPA resilience in low-frequency applications, e.g. wearable fitness gadgets, hearing aid and biomedical instruments. The first contribution of this dissertation is to develop a TRNG prototype from the uncertainty present in photoresistor sensors. The existing sensor-based TRNGs suffer a low random bit generation rate, therefore, are not suitable in real-time applications. The proposed prototype has an average random bit generation rate of 8 kbps, 32 times higher than the existing sensor-based TRNG. The proposed lightweight scrambling method results in random bit entropy close to ideal value 1. The proposed TRNG prototype passes all 15 statistical tests of the National Institute of Standards and Technology (NIST) Statistical Test Suite with quality performance. The second contribution of this dissertation is to develop an integrated TRNG-PUF designed using photovoltaic solar cell sensors. The TRNG and PUF are mutually independent in the way they are designed, therefore, integrating them as one architecture can be beneficial in resource-constrained computing devices. We propose a novel histogram-based technique to segregate photovoltaic solar cell sensor response suitable for TRNG and PUF respectively. The proposed prototype archives approximately 34\% improvement in TRNG output. The proposed prototype achieves an average of 92.13\% reliability and 50.91\% uniformity performance in PUF response. The proposed sensor-based hardware security primitives do not require additional interfacing hardware. Therefore, they can be ported as a software update on existing photoresistor and photovoltaic sensor-based devices. Furthermore, the sensor-based design approach can identify physically tempered and faulty sensor nodes during authentication as their response bit differs. The third contribution is towards the development of a novel 2-phase sinusoidal clocking implementation, 2-SPGAL for existing Symmetric Pass Gate Adiabatic Logic (SPGAL). The proposed 2-SPGAL logic-based LWC cipher PRESENT shows an average of 49.34\% energy saving compared to baseline CMOS logic implementation. Furthermore, the 2-SPGAL prototype has an average of 22.76\% better energy saving compared to 2-EE-SPFAL (2-phase Energy-Efficient-Secure Positive Feedback Adiabatic Logic). The proposed 2-SPGAL was tested for energy-efficiency performance for the frequency range of 50 kHz to 250 kHz, used in healthcare gadgets and biomedical instruments. The proposed 2-SPGAL based design saves 16.78\% transistor count compared to 2-EE-SPFAL counterpart. The final contribution is to explore Clocked CMOS Adiabatic Logic (CCAL) to design a cryptographic circuit. Previously proposed 2-SPGAL and 2-EE-SPFAL uses two complementary pairs of the transistor evaluation network, thus resulting in a higher transistor count compared to the CMOS counterpart. The CCAL structure is very similar to CMOS and unlike 2-SPGAL and 2-EE-SPFAL, it does not require discharge circuitry to improve security performance. The case-study implementation LWC cipher PRESENT S-Box using CCAL results into 45.74\% and 34.88\% transistor count saving compared to 2-EE-SPFAL and 2-SPGAL counterpart. Furthermore, the case-study implementation using CCAL shows more than 95\% energy saving compared to CMOS logic at frequency range 50 kHz to 125 kHz, and approximately 60\% energy saving at frequency 250 kHz. The case study also shows 32.67\% and 11.21\% more energy saving compared to 2-EE-SPFAL and 2-SPGAL respectively at frequency 250 kHz. We also show that 200 fF of tank capacitor in the clock generator circuit results in optimum energy and security performance in CCAL

Energy-Detecting Receivers for Wake-Up Radio Applications

In the energy-limited wireless sensor node applications, wake-up radios are required to reduce the average power consumption of the node. Energy-detecting receivers are the best fit for such low power operations. This thesis presents the energy-detecting receiver design; challenges; techniques to enhance sensitivity, selectivity; and multi-access operation. Self-mixers instead of the conventional envelope detectors are proposed and proved to be optimal for signal detection. A fully integrated wake-up receiver uses the self-mixer and time-encoded baseband signal processing to provide a sensitivity of -79.1dBm at 434MHz with 420pW of power, providing an 8dB better sensitivity at 10dB lower power consumption compared to the SoA. A novel approach using narrowband interferers as local oscillators will be presented to further enhance sensitivity and selectivity, effectively operating the energy-detector receiver as a direct down-conversion receiver. Additionally, a clockless continuous-time analog correlator will be introduced to enhance the selectivity to wide-band AM interferers. The architecture uses pulse-position-encoded analog signal processing with VCOs as integrators and pulse-controlled relaxation delays; it operates as a code-domain matched filter to de-spread asynchronous wake-up codes. This code-domain matched filtering also provides code-division multiple access (CDMA) for simultaneous wakeups. Additional enhancement in the link can be achieved using directional antennas, providing spatial gain and selectivity. Certain applications can leverage a nearby reflector similar to a Yagi antenna to enhance the directivity. A low power directional backscatter tag is proposed, it uses multiple antennas acting as a reflectarray by configuring constant phase gradients depending on the direction of arrival (DoA) of the signal. Thus, instead of harvesting energy, the same energy and the surrounding environment can be leveraged to enhance functionality (e.g. interferer as LO, using a backscatter tag on a wall) for low power operation. Innovations spanning both system and circuit architectures that leverage the ambient energy and environment to enable power-efficient solutions for next-generation wake-up radios are presented in this work

From serendipity to sustainable Green IoT: technical, industrial and political perspective

Recently, Internet of Things (IoT) has become one of the largest electronics market for hardware production due to its fast evolving application space. However, one of the key challenges for IoT hardware is the energy efficiency as most of IoT devices/objects are expected to run on batteries for months/years without a battery replacement or on harvested energy sources. Widespread use of IoT has also led to a largescale rise in the carbon footprint. In this regard, academia, industry and policy-makers are constantly working towards new energy-efficient hardware and software solutions paving the way for an emerging area referred to as green-IoT. With the direct integration and the evolution of smart communication between physical world and computer-based systems, IoT devices are also expected to reduce the total amount of energy consumption for the Information and Communication Technologies (ICT) sector. However, in order to increase its chance of success and to help at reducing the overall energy consumption and carbon emissions a comprehensive investigation into how to achieve green-IoT is required. In this context, this paper surveys the green perspective of the IoT paradigm and aims to contribute at establishing a global approach for green-IoT environments. A comprehensive approach is presented that focuses not only on the specific solutions but also on the interaction among them, and highlights the precautions/decisions the policy makers need to take. On one side, the ongoing European projects and standardization efforts as well as industry and academia based solutions are presented and on the other side, the challenges, open issues, lessons learned and the role of policymakers towards green-IoT are discussed. The survey shows that due to many existing open issues (e.g., technical considerations, lack of standardization, security and privacy, governance and legislation, etc.) that still need to be addressed, a realistic implementation of a sustainable green-IoT environment that could be universally accepted and deployed, is still missing

An Energy Harvesting Solution for IoT Sensors Using MEMS Technology

The significant development of IoT sensors will play a critical role in a large number of applications. It is predicted that billions of IoT sensors will be used worldwide by 2020 [1]. Batteries are commonly utilized to power on sensors, but they are depleted and they require maintenance and replacement. Battery replacement for billions of sensors is a daunting task and battery disposal for IoT sensors can become an environmental problem. Energy harvesting from ambient sources presents a viable solution to overcome these problems. Among all energy sources, light is considered as one of the best sources due to its high energy density and availability in both indoor and outdoor environments. In order to make an energy harvesting system efficient, many methods have been proposed in the literature to extract the maximum energy while minimizing the power consumption by the energy harvesting circuitry. In this work, a boost converter circuit is designed using MEMS-based switches to reduce the leakage current and power loss caused by conventional transistor-based switches. A light energy harvesting method is also proposed utilizing available components of a typical IoT sensor. The reuse of available components in the proposed solution reduces the overall power consumption and the area overhead of the energy harvesting solution

Passive und aktive Radio Frequency Identification Tags im 60-GHz-Band

Die Einführung des millimeter-Wellen-Bandes eröffnet neue Perspektiven für die Radio Frequency Identification (RFID) Kommunikationssysteme. Der Enwurf des Systems im 60-GHz-Band ermöglicht die Implementierung der On-Chip Antenne und darüber hinaus die Implementierung eines RFID-Tags auf einem einzigen Chip. Dennoch ist es aufgrund der gesetzlichen Beschränkung der effektiven isotropen Strahlungsleistung (EIRP) des Lesegeräts und der erhöhten Freiraum-Dielektrikumsverluste eine Herausforderung, eine zuverlässige Kommunikationsreichweite von mehreren Millimetern zu erreichen. Neue Lösungen sind für jeden Block sowohl im Lesegerät als auch im Single-Chip-Tag erforderlich. Obwohl das Lesegerät batteriebetrieben ist, ist es immer noch eine Herausforderung, die maximal zulässigen 20 dBm IERP des Lesersenders energieeffizient zu erzeugen. Darüber hinaus sollte der Empfänger einen ausreichenden Dynamikbereich haben, um das vom Tag kommende Signal zu erkennen. Auf der Tag-Seite sind die Hauptherausforderungen das Co-Design der effizienten On-Chip-Antennen-Implementierung, die hochempfindliche Gleichrichter-Implementierung und das Rückkommunikationskonzept. Diese Arbeit konzentriert sich auf die Machbarkeitsstudie des Single-Chip-RFID-Tags und die Implementierung im Millimeterwellenbereich. Es werden zwei Rückkommunikationskonzepte untersucht - Backscattering-Rückkommunikation und eine Kommunikation unter Verwendung von Ultra-Low-Power (ULP) Radios. Beide werden in einem 22 nm FDSOI Prozess auf einem Substrat mit geringem Widerstand implementiert. Beide Tags arbeiten mit einer Versorgungsspannung von 0,4 V, um die Kommunikationsreichweite zu maximieren. Die Link-Budgets sind so ausgelegt, dass sie die regulatorischen Beschränkungen einhalten. Die Auswahl des Technologieknotens wird begründet. Verschiedene Aspekte im Zusammenhang mit der Technologie werden diskutiert, wie z. B. Geräteleistung, passiver Qualitätsfaktor, Leistungsdichte der Kondensatoren. Der Backscattering RFID-Tag wird zuerst entworfen, da er eine relativ einfachere Topologie hat. Die Probleme der Gleichrichterempfindlichkeit im Rahmen des analogen Frontends, der On-Chip-Antenneneffizienz und der konjugierten Anpassung beider werden untersucht. Eine Kommunikationsreichweite von 5 mm wird angestrebt und realisiert. Um die Kommunikationsreichweite weiter zu erhöhen, wird in der zweiten Phase ein Tag mit einer aktiven Rückkommunikation implementiert. Hier wird die Gleichrichterempfindlichkeit weiter verbessert. Es wird ein 0,4V ULP Radio entworfen, das sich die Antenne mit dem Gleichrichter über einen Single-Pole- Double-Through (SPDT) Schalter teilt. Ein Abstand von 2 cm erwies sich als realisierbar, wobei die gesetzlichen Bestimmungen eingehalten und der dynamische Bereich des Leseempfängers nicht überschritten wurde. Es wird die höchste normalisierte Kommunikationsreichweite pro Leser-EIRP erreicht. Weitere Verbesserungsmöglichkeiten werden diskutiert