885 research outputs found
APOLLO: the Apache Point Observatory Lunar Laser-ranging Operation: Instrument Description and First Detections
A next-generation lunar laser ranging apparatus using the 3.5 m telescope at
the Apache Point Observatory in southern New Mexico has begun science
operation. APOLLO (the Apache Point Observatory Lunar Laser-ranging Operation)
has achieved one-millimeter range precision to the moon which should lead to
approximately one-order-of-magnitude improvements in the precision of several
tests of fundamental properties of gravity. We briefly motivate the scientific
goals, and then give a detailed discussion of the APOLLO instrumentation.Comment: 37 pages; 10 figures; 1 table: accepted for publication in PAS
Quadrature Phase-Domain ADPLL with Integrated On-line Amplitude Locked Loop Calibration for 5G Multi-band Applications
5th generation wireless systems (5G) have expanded frequency band coverage with the low-band 5G and mid-band 5G frequencies spanning 600 MHz to 4 GHz spectrum. This dissertation focuses on a microelectronic implementation of CMOS 65 nm design of an All-Digital Phase Lock Loop (ADPLL), which is a critical component for advanced 5G wireless transceivers. The ADPLL is designed to operate in the frequency bands of 600MHz-930MHz, 2.4GHz-2.8GHz and 3.4GHz-4.2GHz. Unique ADPLL sub-components include: 1) Digital Phase Frequency Detector, 2) Digital Loop Filter, 3) Channel Bank Select Circuit, and 4) Digital Control Oscillator. Integrated with the ADPLL is a 90-degree active RC-CR phase shifter with on-line amplitude locked loop (ALL) calibration to facilitate enhanced image rejection while mitigating the effects of fabrication process variations and component mismatch. A unique high-sensitivity high-speed dynamic voltage comparator is included as a key component of the active phase shifter/ALL calibration subsystem. 65nm CMOS technology circuit designs are included for the ADPLL and active phase shifter with simulation performance assessments. Phase noise results for 1 MHz offset with carrier frequencies of 600MHz, 2.4GHz, and 3.8GHz are -130, -122, and -116 dBc/Hz, respectively. Monte Carlo simulations to account for process variations/component mismatch show that the active phase shifter with ALL calibration maintains accurate quadrature phase outputs when operating within the frequency bands 600MHz-930MHz, 2.4GHz-2.8GHz and 3.4GHz-4.2GHz
Reconfigurable time interval measurement circuit incorporating a programmable gain time difference amplifier
PhD ThesisAs further advances are made in semiconductor manufacturing technology the performance of circuits is continuously increasing. Unfortunately, as the technology node descends deeper into the nanometre region, achieving the potential performance gain is becoming more of a challenge; due not only to the effects of process variation but also to the reduced timing margins between signals within the circuit creating timing problems. Production Standard Automatic Test Equipment (ATE) is incapable of performing internal timing measurements due, first to the lack of accessibility and second to the overall timing accuracy of the tester which is grossly inadequate. To address these issue ‘on-chip’ time measurement circuits have been developed in a similar way that built in self-test (BIST) evolved for ‘on-chip’ logic testing.
This thesis describes the design and analysis of three time amplifier circuits. The analysis undertaken considers the operational aspects related to gain and input dynamic range, together with the robustness of the circuits to the effects of process, voltage and temperature (PVT) variations. The design which had the best overall performance was subsequently compared to a benchmark design, which used the ‘buffer delay offset’ technique for time amplification, and showed a marked 6.5 times improvement on the dynamic range extending this from 40 ps to 300ps. The new design was also more robust to the effects of PVT variations.
The new time amplifier design was further developed to include an adjustable gain capability which could be varied in steps of approximately 7.5 from 4 to 117. The time amplifier was then connected to a 32-stage tapped delay line to create a reconfigurable time measurement circuit with an adjustable resolution range from 15 down to 0.5 ps and a dynamic range from 480 down to 16 ps depending upon the gain setting. The overall footprint of the measurement circuit, together with its calibration module occupies an area of 0.026 mm2
The final circuit, overall, satisfied the main design criteria for ‘on-chip’ time measurement circuitry, namely, it has a wide dynamic range, high resolution, robust to the effects of PVT and has a small area overhead.Umm Al-Qura University
An On-chip PVT Resilient Short Time Measurement Technique
As the CMOS technology nodes continue to shrink, the challenges of developing manufacturing tests for integrated circuits become more difficult to address. To detect parametric faults of new generation of integrated circuits such as 3D ICs, on-chip short-time intervals have to be accurately measured. The accuracy of an on-chip time measurement module is heavily affected by Process, supply Voltage, and Temperature (PVT) variations. This work presents a new on-chip time measurement scheme where the undesired effects of PVT variations are attenuated significantly. To overcome the effects of PVT variations on short-time measurement, phase locking methodology is utilized to implement a robust Vernier delay line. A prototype Time-to-Digital Converter (TDC) has been fabricated using TSMC 0.180 µm CMOS technology and experimental measurements have been carried out to verify the performance parameters of the TDC. The measurement results indicate that the proposed solution reduces the effects of PVT variations by more than tenfold compared to a conventional on-chip TDC. A coarse-fine time interval measurement scheme which is resilient to the PVT variations is also proposed. In this approach, two Delay Locked Loops (DLLs) are utilized to minimize the effects of PVT on the measured time intervals. The proposed scheme has been implemented using CMOS 65nm technology. Simulation results using Advanced Design System (ADS) indicate that the measurement resolution varies by less than 0.1ps with ±15% variations of the supply voltage. The proposed method also presents a robust performance against process and temperature variations. The measurement accuracy changes by a maximum of 0.05ps from slow to fast corners. The implemented TDC presents a robust performance against temperature variations too and its measurement accuracy varies a few femto-seconds from -40 ºC to +100 ºC. The principle of robust short-time measurement was used in practice to design and implement a state-of-the-art Coordinate Measuring Machine (CMM) for an industry partner to measure geometrical features of transmission parts with micrometer resolution. The solution developed for the industry partner has resulted in a patent and a product in the market. The on-chip short-time measurement technology has also been utilized to develop a solution to detect Hardware Trojans
Electronics for Sensors
The aim of this Special Issue is to explore new advanced solutions in electronic systems and interfaces to be employed in sensors, describing best practices, implementations, and applications. The selected papers in particular concern photomultiplier tubes (PMTs) and silicon photomultipliers (SiPMs) interfaces and applications, techniques for monitoring radiation levels, electronics for biomedical applications, design and applications of time-to-digital converters, interfaces for image sensors, and general-purpose theory and topologies for electronic interfaces
Online Timing Slack Measurement and its Application in Field-Programmable Gate Arrays
Reliability, power consumption and timing performance are key concerns for today's integrated circuits. Measurement techniques capable of quantifying the timing characteristics of a circuit, while it is operating, facilitate a range of benefits. Delay variation due to environmental and operational conditions, and degradation can be monitored by tracking changes in timing performance. Using the measurements in a closed-loop to control power supply voltage or clock frequency allows for the reduction of timing safety margins, leading to improvements in power consumption or throughput performance through the exploitation of better-than worst-case operation.
This thesis describes a novel online timing slack measurement method which can directly measure the timing performance of a circuit, accurately and with minimal overhead. Enhancements allow for the improvement of absolute accuracy and resolution. A compilation flow is reported that can automatically instrument arbitrary circuits on FPGAs with the measurement circuitry. On its own this measurement method is able to track the "health" of an integrated circuit, from commissioning through its lifetime, warning of impending failure or instigating pre-emptive degradation mitigation techniques.
The use of the measurement method in a closed-loop dynamic voltage and frequency scaling scheme has been demonstrated, achieving significant improvements in power consumption and throughput performance.Open Acces
Recommended from our members
TIME-DIFFERENCE CIRCUITS: METHODOLOGY, DESIGN, AND DIGITAL REALIZATION
This thesis presents innovations for a special class of circuits called Time Difference (TD) circuits. We introduce a signal processing methodology with TD signals that alters the target signal from a magnitude perspective to time interval between two time events and systematically organizes the primary TD functions abstracted from existing TD circuits and systems. The TD circuits draw attention from a broad range of application fields. In addition, highly evolved complementary metal-oxide-semiconductor (CMOS) technology suffers from various problems related to voltage and current amplitude signal processing methods. Compared to traditional analog and digital circuits, TD circuits bring several compelling features: high-resolution, high-throughput, and low-design complexity with digital integration capability. Further, the fabrication technology is advancing into the nanometer regime; the reduction in voltage headroom limits the performance of traditional analog/mixed-signal designs. All-digital design of time-difference circuit needs to be stressed to adapt to the low-cost, low-power, and high-portability applications.
We focus on Time-to-Digital Converters (TDC), one of the crucial building blocks in TD circuits. A novel algorithmic architecture is proposed based on a binary search algorithm and validated with both simulation and fabricated silicon. An all-digital structure Time-difference Amplifier (TDA) is designed and implemented to make FPGA and other all-digital implementations for TDC and related TD circuits feasible. Besides, we propose an all-digital timing measurement circuit based on the process variation from CMOS fabrication: PVTMC, which achieves a high measurement resolution:
Recommended from our members
High-Speed Wide-Field Time-Correlated Single-Photon Counting Fluorescence Lifetime Imaging Microscopy
Fluorescence microscopy is a powerful imaging technique used in the biological sciences to identify labeled components of a sample with specificity. This is usually accomplished through labeling with fluorescent dyes, isolating these dyes by their spectral signatures with optical filters, and recording the intensity of the fluorescent response. Although these techniques are widely used, fluorescence intensity images can be negatively affected by a variety of factors that impact the fluorescence intensity. Fluorescence lifetime imaging microscopy (FLIM) is an imaging technique that is relatively immune to intensity fluctuations and also provides the unique ability to directly monitor the microenvironment surrounding a fluorophore. Despite the benefits associated with FLIM, the applications to which it is applied are fairly limited due to long image acquisition times and high cost of traditional hardware. Recent advances in complementary metal-oxide-semiconductor (CMOS) single-photon avalanche diodes (SPADs) have enabled the design of low-cost imaging arrays that are capable of recording lifetime images with acquisition times greater than one order of magnitude faster than existing systems. However, these SPAD arrays have yet to realize the full potential of the technology due to limitations in their ability to handle the vast amount of data generated during the commonly used time-correlated single-photon counting (TCSPC) lifetime imaging technique. This thesis presents the design, implementation, characterization, and demonstration of a high speed FLIM imaging system. The components of this design include a CMOS imager chip in a standard 0.13 μm technology containing a custom CMOS SPAD, a 64-by-64 array of these SPADs, pixel control circuitry, independent time-to-digital converters (TDCs), a FLIM specific datapath, and high bandwidth output buffers. In addition to the CMOS imaging array, a complete system was designed and implemented using a printed circuit board (PCB) for capturing data from the imager, creating histograms for the photon arrival data using field-programmable gate arrays, and transferring the data to a computer using a cabled PCIe interface. Finally, software is used to communicate between the imaging system and a computer.The dark count rate of the SPAD was measured to be only 231 Hz at room temperature while maintaining a photon detection probability of up to 30\%. TDCs included on the array have a 62.5 ps resolution and a 64 ns range, which is suitable for measuring the lifetime of most biological fluorophores. Additionally, the on-chip datapath was designed to handle continuous data transfers at rates capable of supporting TCSPC-based lifetime imaging at 100 frames per second. The system level implementation also provides sufficient data throughput for transferring up to 750 frames per second from the imaging system to a computer. The lifetime imaging system was characterized using standard techniques for evaluating SPAD performance and an electrical delay signal for measuring the TDC performance. This thesis concludes with a demonstration of TCSPC-FLIM imaging at 100 frames per second -- the fastest 64-by-64 TCSPC FLIM that has been demonstrated. This system overcomes some of the limitations of existing FLIM systems and has the potential to enable new application domains in dynamic FLIM imaging
- …