Multipath Miller Compensation for Switched-Capacitor Systems

A hybrid operational amplifier compensation technique using Miller and multipath compensation is presented for multi-stage amplifier designs. Unconditional stability is achieved by the means of pole-zero cancellation where left-half zeros cancel out the non-dominant poles of the operational amplifier. The compensation technique is stable over process, temperature, and voltage variations. Compared to conventional Miller-compensation, the proposed compensation technique exhibits improved settling response for operational amplifiers with the same gain, bandwidth, power, and area. For the same settling time, the proposed compensation technique will require less area and consume less power than conventional Miller-compensation. Furthermore, the proposed technique exhibits improved output slew rate and lower noise over the conventional Miller-compensation technique. Two-stage operational amplifiers were designed in a 0.18µm CMOS process using the proposed technique and conventional Miller-compensated technique. The design procedure for the two-stage amplifier is applicable for higher-order amplifier designs. The amplifiers were incorporated into a switched-capacitor oscillator where the oscillation harmonics are dependent on the settling behaviour of the op amps. The superior settling response of the proposed compensation technique results in a improved output waveform from the oscillator

Analog Block Evaluation with BIST Instruments

The demands for quality and for the ability to compete in the market make it necessary not only to facilitate the testing of analog circuits but also to make them more efficient. With the increase in systems complexity and level of integration, the process of testing analog circuits has become difficult and expensive. This dissertation, proposed by Synopsys Portugal, aims to perform a study on analog Built-In Self-Test (BIST) and implement a simple analog BIST system that is capable of testing a voltage regulator and an oscillator on specifics parameters. In the regulator, the parameters to test are: Over and Under Voltage, Settling Time and Voltage Ripple. In the oscillator the parameters to test are: Frequency Drift, Settling Time and Duty-Cycle Distortion. This methodology allows for self-test operations and, thus, reduces complexity and cost associated with performing analog circuit tests. It makes it possible to test the circuits periodically throughout its lifetime and also monitors some analog parameters in real-time

Online Timing Slack Measurement and its Application in Field-Programmable Gate Arrays

Reliability, power consumption and timing performance are key concerns for today's integrated circuits. Measurement techniques capable of quantifying the timing characteristics of a circuit, while it is operating, facilitate a range of benefits. Delay variation due to environmental and operational conditions, and degradation can be monitored by tracking changes in timing performance. Using the measurements in a closed-loop to control power supply voltage or clock frequency allows for the reduction of timing safety margins, leading to improvements in power consumption or throughput performance through the exploitation of better-than worst-case operation. This thesis describes a novel online timing slack measurement method which can directly measure the timing performance of a circuit, accurately and with minimal overhead. Enhancements allow for the improvement of absolute accuracy and resolution. A compilation flow is reported that can automatically instrument arbitrary circuits on FPGAs with the measurement circuitry. On its own this measurement method is able to track the "health" of an integrated circuit, from commissioning through its lifetime, warning of impending failure or instigating pre-emptive degradation mitigation techniques. The use of the measurement method in a closed-loop dynamic voltage and frequency scaling scheme has been demonstrated, achieving significant improvements in power consumption and throughput performance.Open Acces

Sincronização em sistemas integrados a alta velocidade

Doutoramento em Engenharia ElectrotécnicaA distribui ção de um sinal relógio, com elevada precisão espacial (baixo skew) e temporal (baixo jitter ), em sistemas sí ncronos de alta velocidade tem-se revelado uma tarefa cada vez mais demorada e complexa devido ao escalonamento da tecnologia. Com a diminuição das dimensões dos dispositivos e a integração crescente de mais funcionalidades nos Circuitos Integrados (CIs), a precisão associada as transições do sinal de relógio tem sido cada vez mais afectada por varia ções de processo, tensão e temperatura. Esta tese aborda o problema da incerteza de rel ogio em CIs de alta velocidade, com o objetivo de determinar os limites do paradigma de desenho sí ncrono. Na prossecu ção deste objectivo principal, esta tese propõe quatro novos modelos de incerteza com âmbitos de aplicação diferentes. O primeiro modelo permite estimar a incerteza introduzida por um inversor est atico CMOS, com base em parâmetros simples e su cientemente gen éricos para que possa ser usado na previsão das limitações temporais de circuitos mais complexos, mesmo na fase inicial do projeto. O segundo modelo, permite estimar a incerteza em repetidores com liga ções RC e assim otimizar o dimensionamento da rede de distribui ção de relógio, com baixo esfor ço computacional. O terceiro modelo permite estimar a acumula ção de incerteza em cascatas de repetidores. Uma vez que este modelo tem em considera ção a correla ção entre fontes de ruí do, e especialmente util para promover t ecnicas de distribui ção de rel ogio e de alimentação que possam minimizar a acumulação de incerteza. O quarto modelo permite estimar a incerteza temporal em sistemas com m ultiplos dom ínios de sincronismo. Este modelo pode ser facilmente incorporado numa ferramenta autom atica para determinar a melhor topologia para uma determinada aplicação ou para avaliar a tolerância do sistema ao ru ído de alimentação. Finalmente, usando os modelos propostos, são discutidas as tendências da precisão de rel ogio. Conclui-se que os limites da precisão do rel ogio são, em ultima an alise, impostos por fontes de varia ção dinâmica que se preveem crescentes na actual l ogica de escalonamento dos dispositivos. Assim sendo, esta tese defende a procura de solu ções em outros ní veis de abstração, que não apenas o ní vel f sico, que possam contribuir para o aumento de desempenho dos CIs e que tenham um menor impacto nos pressupostos do paradigma de desenho sí ncrono.Distributing a the clock simultaneously everywhere (low skew) and periodically everywhere (low jitter) in high-performance Integrated Circuits (ICs) has become an increasingly di cult and time-consuming task, due to technology scaling. As transistor dimensions shrink and more functionality is packed into an IC, clock precision becomes increasingly a ected by Process, Voltage and Temperature (PVT) variations. This thesis addresses the problem of clock uncertainty in high-performance ICs, in order to determine the limits of the synchronous design paradigm. In pursuit of this main goal, this thesis proposes four new uncertainty models, with di erent underlying principles and scopes. The rst model targets uncertainty in static CMOS inverters. The main advantage of this model is that it depends only on parameters that can easily be obtained. Thus, it can provide information on upcoming constraints very early in the design stage. The second model addresses uncertainty in repeaters with RC interconnects, allowing the designer to optimise the repeater's size and spacing, for a given uncertainty budget, with low computational e ort. The third model, can be used to predict jitter accumulation in cascaded repeaters, like clock trees or delay lines. Because it takes into consideration correlations among variability sources, it can also be useful to promote oorplan-based power and clock distribution design in order to minimise jitter accumulation. A fourth model is proposed to analyse uncertainty in systems with multiple synchronous domains. It can be easily incorporated in an automatic tool to determine the best topology for a given application or to evaluate the system's tolerance to power-supply noise. Finally, using the proposed models, this thesis discusses clock precision trends. Results show that limits in clock precision are ultimately imposed by dynamic uncertainty, which is expected to continue increasing with technology scaling. Therefore, it advocates the search for solutions at other abstraction levels, and not only at the physical level, that may increase system performance with a smaller impact on the assumptions behind the synchronous design paradigm

High-Speed and Low-Energy On-Chip Communication Circuits.

Continuous technology scaling sharply reduces transistor delays, while fixed-length global wire delays have increased due to less wiring pitch with higher resistance and coupling capacitance. Due to this ever growing gap, long on-chip interconnects pose well-known latency, bandwidth, and energy challenges to high-performance VLSI systems. Repeaters effectively mitigate wire RC effects but do little to improve their energy costs. Moreover, the increased complexity and high level of integration requires higher wire densities, worsening crosstalk noise and power consumption of conventionally repeated interconnects. Such increasing concerns in global on-chip wires motivate circuits to improve wire performance and energy while reducing the number of repeaters. This work presents circuit techniques and investigation for high-performance and energy-efficient on-chip communication in the aspects of encoding, data compression, self-timed current injection, signal pre-emphasis, low-swing signaling, and technology mapping. The improved bus designs also consider the constraints of robust operation and performance/energy gains across process corners and design space. Measurement results from 5mm links on 65nm and 90nm prototype chips validate 2.5-3X improvement in energy-delay product.Ph.D.Electrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/75800/1/jseo_1.pd

Mixed-signal integrated circuits design and validation for automotive electronics applications

Automotive electronics is a fast growing market. In a field primarily dominated by mechanical or hydraulic systems, over the past few decades there has been exponential growth in the number of electronic components incorporated into automobiles. Partly thanks to the advance in high voltage smart power processes in nowadays cars is possible to integrate both power/high voltage electronics and analog/digital signal processing circuitry thus allowing to replace a lot of mechanical systems with electro-mechanical or fully electronic ones. High level modeling of complex electronic systems is gaining importance relatively to design space exploration, enabling shorter design and verification cycles, allowing reduced time-to-market. A high level model of a resistor string DAC to evaluate nonlinearities has been developed in MATLAB environment. As a test case for the model, a 10 bit resistive DAC in 0.18um is designed and the results were compared with the traditional transistor level approach. Then we face the analysis and design of a fundamental block: the bandgap voltage reference. Automotive requirements are tough, so the design of the voltage reference includes a pre-regulation part of the battery voltage that allows to enhance overall performances. Moreover an analog integrated driver for an automotive application whose architecture exploits today’s trends of analog-digital integration allowing a greater range of flexibility allowing high configurability and fast prototipization is presented. We covered also the mixed-signal verification approach. In fact, as complexity increases and mixed-signal systems become more and more pervasive, test and verification often tend to be the bottleneck in terms of time effort. A complete flow for mixed-signal verification using VHDL-AMS modeling and Python scripting is presented as an alternative to complex transistor level simulations. Finally conclusions are drawn

Design and realization of a 2.4 Gbps - 3.2 Gbps clock and data recovery circuit

This thesis presents the design, verification, system integration and the physical realization of a high-speed monolithic phase-locked loop (PLL) based clock and data recovery (CDR) circuit. The architecture of the CDR has been realized as a two-loop structure consisting of coarse and fine loops, each of which is capable of processing the incoming low-speed reference clock and high-speed random data. At start up, the coarse loop provides fast locking to the system frequency with the help of the reference clock. After the VCO clock reaches a proximity of system frequency , the LOCK signal is generated and the coarse loop is tumed off, while the fine loop is tumed on. Fine loop tracks the phase of the generated clock with respect to the data and aligns the VCO clock such that its rising edge is in the middle of data eye. The speed and symmetry of sub-blocks in fine loop are extremely important, since all asymmetric charging effects, skew and setup/hold problems in this loop translate into a static phase error at the clock output. The entire circuit architecture is built with a special low-voltage circuit design technique. All analogue as well as digital sub-blocks of the CDR architecture presented in this work operate on a differential signalling, which significantly makes the design more complex while ensuring a more robust perforrnance. Other important features of this CDR include small area, single power supply, low power consumption, capability to operate at very high data rates, and the ability to handle between 2.4 Gbps and 3.2 Gbps data rate. The CDR architecture was realized using a conventional 0.13-mikrometer digital CMOS technology (Foundry: UMC), which ensures a lower overall cost and better portability for the design. The CDR architecture presented in this work is capable of operating at sampling frequencies of up to 3.2 GHz, and still can achieve the robust phase alignrnent. The entire circuit is designed with single 1.2 V power supply .The overall power consumption is estimated as 18.6 mW at 3.2 GHz sampling rate. The overall silicon area of the CDR is approximately 0.3 mm^2 with its internal loop filter capacitors. Other researchers have reported similar featured PLL-based clock and data recovery circuits in terms of operating data rate, architecture and jitter performance. To the best of our knowledge, this clock recovery uses the advantage of being the first high-speed CDR designed in CMOS 0.13 mikrometer technology with the superiority on power consumption and area considerations among others. The CDR architecture presented in this thesis is intended, as a state-of-the-art clock recovery for high-speed applications such as optical communications or high bandwidth serial wireline communication needs. It can be used either as a stand-alone single-chip unit, or as an embedded intellectual property (IP) block that can be integrated with other modules on chip

Design of High-Speed SerDes Transceiver for Chip-to-Chip Communications in CMOS Process

With the continuous increase of on-chip computation capacities and exponential growth of data-intensive applications, the high-speed data transmission through serial links has become the backbone for modern communication systems. To satisfy the massive data-exchanging requirement, the data rate of such serial links has been updated from several Gb/s to tens of Gb/s. Currently, the commercial standards such as Ethernet 400GbE, InfiniBand high data rate (HDR), and common electrical interface (CEI)-56G has been developing towards 40+ Gb/s. As the core component within these links, the transceiver chipset plays a fundamental role in balancing the operation speed, power consumption, area occupation, and operation range. Meanwhile, the CMOS process has become the dominant technology in modern transceiver chip fabrications due to its large-scale digital integration capability and aggressive pricing advantage. This research aims to explore advanced techniques that are capable of exploiting the maximum operation speed of the CMOS process, and hence provides potential solutions for 40+ Gb/s CMOS transceiver designs. The major contributions are summarized as follows. A low jitter ring-oscillator-based injection-locked clock multiplier (RILCM) with a hybrid frequency tracking loop that consists of a traditional phase-locked loop (PLL), a timing-adjusted loop, and a loop selection state-machine is implemented in 65-nm C-MOS process. In the ring voltage-controlled oscillator, a full-swing pseudo-differential delay cell is proposed to lower the device noise to phase noise conversion. To obtain high operation speed and high detection accuracy, a compact timing-adjusted phase detector tightly combined with a well-matched charge pump is designed. Meanwhile, a lock-loss detection and lock recovery is devised to endow the RILCM with a similar lock-acquisition ability as conventional PLL, thus excluding the initial frequency set- I up aid and preventing the potential lock-loss risk. The experimental results show that the figure-of-merit of the designed RILCM reaches -247.3 dB, which is better than previous RILCMs and even comparable to the large-area LC-ILCMs. The transmitter (TX) and receiver (RX) chips are separately designed and fab- ricated in 65-nm CMOS process. The transmitter chip employs a quarter-rate multi-multiplexer (MUX)-based 4-tap feed-forward equalizer (FFE) to pre-distort the output. To increase the maximum operating speed, a bandwidth-enhanced 4:1 MUX with the capability of eliminating charge-sharing effect is proposed. To produce the quarter-rate parallel data streams with appropriate delays, a compact latch array associated with an interleaved-retiming technique is designed. The receiver chip employs a two-stage continuous-time linear equalizer (CTLE) as the analog front-end and integrates an improved clock data recovery to extract the sampling clocks and retime the incoming data. To automatically balance the jitter tracking and jitter suppression, passive low-pass filters with adaptively-adjusted bandwidth are introduced into the data-sampling path. To optimize the linearity of the phase interpolation, a time-averaging-based compensating phase interpolator is proposed. For equalization, a combined TX-FFE and RX-CTLE is applied to compensate for the channel loss, where a low-cost edge-data correlation-based sign zero-forcing adaptation algorithm is proposed to automatically adjust the TX-FFE’s tap weights. Measurement results show that the fabricated transmitter/receiver chipset can deliver 40 Gb/s random data at a bit error rate of 16 dB loss at the half-baud frequency, while consuming a total power of 370 mW

Energy-Efficient Digital Signal Processing Hardware Design.

As CMOS technology has developed considerably in the last few decades, many SoCs have been implemented across different application areas due to reduced area and power consumption. Digital signal processing (DSP) algorithms are frequently employed in these systems to achieve more accurate operation or faster computation. However, CMOS technology scaling started to slow down recently and relatively large systems consume too much power to rely only on the scaling effect while system power budget such as battery capacity improves slowly. In addition, there exist increasing needs for miniaturized computing systems including sensor nodes that can accomplish similar operations with significantly smaller power budget. Voltage scaling is one of the most promising power saving techniques due to quadratic switching power reduction effect, making it necessary feature for even high-end processors. However, in order to achieve maximum possible energy efficiency, systems should operate in near or sub-threshold regimes where leakage takes significant portion of power. In this dissertation, a few key energy-aware design approaches are described. Considering prominent leakage and larger PVT variability in low operating voltages, multi-level energy saving techniques to be described are applied to key building blocks in DSP applications: architecture study, algorithm-architecture co-optimization, and robust yet low-power memory design. Finally, described approaches are applied to design examples including a visual navigation accelerator, ultra-low power biomedical SoC and face detection/recognition processor, resulting in 2~100 times power savings than state-of-the-art.PhDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/110496/1/djeon_1.pd

A Bang-Bang All-Digital PLL for Frequency Synthesis

abstract: Phase locked loops are an integral part of any electronic system that requires a clock signal and find use in a broad range of applications such as clock and data recovery circuits for high speed serial I/O and frequency synthesizers for RF transceivers and ADCs. Traditionally, PLLs have been primarily analog in nature and since the development of the charge pump PLL, they have almost exclusively been analog. Recently, however, much research has been focused on ADPLLs because of their scalability, flexibility and higher noise immunity. This research investigates some of the latest all-digital PLL architectures and discusses the qualities and tradeoffs of each. A highly flexible and scalable all-digital PLL based frequency synthesizer is implemented in 180 nm CMOS process. This implementation makes use of a binary phase detector, also commonly called a bang-bang phase detector, which has potential of use in high-speed, sub-micron processes due to the simplicity of the phase detector which can be implemented with a simple D flip flop. Due to the nonlinearity introduced by the phase detector, there are certain performance limitations. This architecture incorporates a separate frequency control loop which can alleviate some of these limitations, such as lock range and acquisition time.Dissertation/ThesisM.S. Electrical Engineering 201