Runtime Scheduling, Allocation, and Execution of Real-Time Hardware Tasks onto Xilinx FPGAs Subject to Fault Occurrence

This paper describes a novel way to exploit the computation capabilities delivered by modern Field-Programmable Gate Arrays (FPGAs), not only towards a higher performance, but also towards an improved reliability. Computation-specific pieces of circuitry are dynamically scheduled and allocated to different resources on the chip based on a set of novel algorithms which are described in detail in this article. These algorithms consider most of the technological constraints existing in modern partially reconfigurable FPGAs as well as spontaneously occurring faults and emerging permanent damage in the silicon substrate of the chip. In addition, the algorithms target other important aspects such as communications and synchronization among the different computations that are carried out, either concurrently or at different times. The effectiveness of the proposed algorithms is tested by means of a wide range of synthetic simulations, and, notably, a proof-of-concept implementation of them using real FPGA hardware is outlined

A New Methodology to Manage FPGA Distributed Memory Content via Bitstream for Xilinx ZYNQ Devices

This paper proposes a methodology to access data and manage the content of distributed memories in FPGA designs through the configuration bitstream. Thanks to the methods proposed, it is possible to read and write the data content of registers without using the in/out ports of registers in a straightforward fashion. Hence, it offers the possibility of performing several operations, such as, to load, copy or compare the information stored in registers without the necessity of physical interconnections. This work includes two flows that simplify the designing process when using the proposed approach: while the first enables the protection or unprotection of writing on different partial regions through the bitstream, the second permits homogeneous instances of a design implemented in different reconfigurable regions to be obtained without losing efficiency. The approach is based and has been physically validated on the ZYNQ from Xilinx, and when using partially reconfigurable designs, it does not affect the hardware overhead nor the maximum operating frequency of the design.This work has been supported, within the fund for research groups of the Basque university system IT1440-22, by the Department of Education and, within PILAR ZE-2020/00022 and COMMUTE ZE-2021/00931 projects, by the Hazitek program, both of the Basque Government; the latter also by the Ministerio de Ciencia Innovación of Spain through the Centro para el Desarrollo Tecnológico Industrial (CDTI) within the projects IDI-20201264 and IDI-20220543, and through the Fondo Europeo de Desarrollo Regional 2014–2020 (FEDER funds)

MURAC: A unified machine model for heterogeneous computers

Includes bibliographical referencesHeterogeneous computing enables the performance and energy advantages of multiple distinct processing architectures to be efficiently exploited within a single machine. These systems are capable of delivering large performance increases by matching the applications to architectures that are most suited to them. The Multiple Runtime-reconfigurable Architecture Computer (MURAC) model has been proposed to tackle the problems commonly found in the design and usage of these machines. This model presents a system-level approach that creates a clear separation of concerns between the system implementer and the application developer. The three key concepts that make up the MURAC model are a unified machine model, a unified instruction stream and a unified memory space. A simple programming model built upon these abstractions provides a consistent interface for interacting with the underlying machine to the user application. This programming model simplifies application partitioning between hardware and software and allows the easy integration of different execution models within the single control ow of a mixed-architecture application. The theoretical and practical trade-offs of the proposed model have been explored through the design of several systems. An instruction-accurate system simulator has been developed that supports the simulated execution of mixed-architecture applications. An embedded System-on-Chip implementation has been used to measure the overhead in hardware resources required to support the model, which was found to be minimal. An implementation of the model within an operating system on a tightly-coupled reconfigurable processor platform has been created. This implementation is used to extend the software scheduler to allow for the full support of mixed-architecture applications in a multitasking environment. Different scheduling strategies have been tested using this scheduler for mixed-architecture applications. The design and implementation of these systems has shown that a unified abstraction model for heterogeneous computers provides important usability benefits to system and application designers. These benefits are achieved through a consistent view of the multiple different architectures to the operating system and user applications. This allows them to focus on achieving their performance and efficiency goals by gaining the benefits of different execution models during runtime without the complex implementation details of the system-level synchronisation and coordination

Towards the development of a reliable reconfigurable real-time operating system on FPGAs

In the last two decades, Field Programmable Gate Arrays (FPGAs) have been rapidly developed from simple “glue-logic” to a powerful platform capable of implementing a System on Chip (SoC). Modern FPGAs achieve not only the high performance compared with General Purpose Processors (GPPs), thanks to hardware parallelism and dedication, but also better programming flexibility, in comparison to Application Specific Integrated Circuits (ASICs). Moreover, the hardware programming flexibility of FPGAs is further harnessed for both performance and manipulability, which makes Dynamic Partial Reconfiguration (DPR) possible. DPR allows a part or parts of a circuit to be reconfigured at run-time, without interrupting the rest of the chip’s operation. As a result, hardware resources can be more efficiently exploited since the chip resources can be reused by swapping in or out hardware tasks to or from the chip in a time-multiplexed fashion. In addition, DPR improves fault tolerance against transient errors and permanent damage, such as Single Event Upsets (SEUs) can be mitigated by reconfiguring the FPGA to avoid error accumulation. Furthermore, power and heat can be reduced by removing finished or idle tasks from the chip. For all these reasons above, DPR has significantly promoted Reconfigurable Computing (RC) and has become a very hot topic. However, since hardware integration is increasing at an exponential rate, and applications are becoming more complex with the growth of user demands, highlevel application design and low-level hardware implementation are increasingly separated and layered. As a consequence, users can obtain little advantage from DPR without the support of system-level middleware. To bridge the gap between the high-level application and the low-level hardware implementation, this thesis presents the important contributions towards a Reliable, Reconfigurable and Real-Time Operating System (R3TOS), which facilitates the user exploitation of DPR from the application level, by managing the complex hardware in the background. In R3TOS, hardware tasks behave just like software tasks, which can be created, scheduled, and mapped to different computing resources on the fly. The novel contributions of this work are: 1) a novel implementation of an efficient task scheduler and allocator; 2) implementation of a novel real-time scheduling algorithm (FAEDF) and two efficacious allocating algorithms (EAC and EVC), which schedule tasks in real-time and circumvent emerging faults while maintaining more compact empty areas. 3) Design and implementation of a faulttolerant microprocessor by harnessing the existing FPGA resources, such as Error Correction Code (ECC) and configuration primitives. 4) A novel symmetric multiprocessing (SMP)-based architectures that supports shared memory programing interface. 5) Two demonstrations of the integrated system, including a) the K-Nearest Neighbour classifier, which is a non-parametric classification algorithm widely used in various fields of data mining; and b) pairwise sequence alignment, namely the Smith Waterman algorithm, used for identifying similarities between two biological sequences. R3TOS gives considerably higher flexibility to support scalable multi-user, multitasking applications, whereby resources can be dynamically managed in respect of user requirements and hardware availability. Benefiting from this, not only the hardware resources can be more efficiently used, but also the system performance can be significantly increased. Results show that the scheduling and allocating efficiencies have been improved up to 2x, and the overall system performance is further improved by ~2.5x. Future work includes the development of Network on Chip (NoC), which is expected to further increase the communication throughput; as well as the standardization and automation of our system design, which will be carried out in line with the enablement of other high-level synthesis tools, to allow application developers to benefit from the system in a more efficient manner

Revisiting the high-performance reconfigurable computing for future datacenters

Modern datacenters are reinforcing the computational power and energy efficiency by assimilating field programmable gate arrays (FPGAs). The sustainability of this large-scale integration depends on enabling multi-tenant FPGAs. This requisite amplifies the importance of communication architecture and virtualization method with the required features in order to meet the high-end objective. Consequently, in the last decade, academia and industry proposed several virtualization techniques and hardware architectures for addressing resource management, scheduling, adoptability, segregation, scalability, performance-overhead, availability, programmability, time-to-market, security, and mainly, multitenancy. This paper provides an extensive survey covering three important aspects-discussion on non-standard terms used in existing literature, network-on-chip evaluation choices as a mean to explore the communication architecture, and virtualization methods under latest classification. The purpose is to emphasize the importance of choosing appropriate communication architecture, virtualization technique and standard language to evolve the multi-tenant FPGAs in datacenters. None of the previous surveys encapsulated these aspects in one writing. Open problems are indicated for scientific community as well

Parallel and Distributed Computing

The 14 chapters presented in this book cover a wide variety of representative works ranging from hardware design to application development. Particularly, the topics that are addressed are programmable and reconfigurable devices and systems, dependability of GPUs (General Purpose Units), network topologies, cache coherence protocols, resource allocation, scheduling algorithms, peertopeer networks, largescale network simulation, and parallel routines and algorithms. In this way, the articles included in this book constitute an excellent reference for engineers and researchers who have particular interests in each of these topics in parallel and distributed computing