Study of Radiation-Tolerant SRAM Design

Static Random Access Memories (SRAMs) are important storage components and widely used in digital systems. Meanwhile, with the continuous development and progress of aerospace technologies, SRAMs are increasingly used in electronic systems for spacecraft and satellites. Energetic particles in space environments can cause single event upsets normally referred as soft errors in the memories, which can lead to the failure of systems. Nowadays electronics at the ground level also experience this kind of upset mainly due to cosmic neutrons and alpha particles from packaging materials, and the failure rate can be 10 to 100 times higher than the errors from hardware failures. Therefore, it is important to study the single event effects in SRAMs and develop cost-effective techniques to mitigate these errors. The objectives of this thesis are to evaluate the current mitigation techniques of single event effects in SRAMs and develop a radiation-tolerant SRAM based on the developed techniques. Various radiation sources and the mechanism of their respective effects in Complementary Metal-Oxide Semiconductors(CMOS) devices are reviewed first in the thesis. The radiation effects in the SRAMs, specifically single event effects are studied, and various mitigation techniques are evaluated. Error-correcting codes (ECC) are studied in the thesis since they can detect and correct single bit errors in the cell array, and it is a effective method with low overhead in terms of area, speed, and power. Hamming codes are selected and implemented in the design of the SRAM, to protect the cells from single event upsets in the SRAM. The simulation results show they can prevent the single bit errors in the cell arrays with low area and speed overhead. Another important and vulnerable part of SRAMs in radiation environments is the sense amplifier. It may not generate the correct output during the reading operation if it is hit by an energetic particle. A novel fault-tolerant sense amplifier is introduced and validated with simulations. The results showed that the performance of the new design can be more than ten times better than that of the reference design. When combining the SRAM cell arrays protected with ECC and the radiation-tolerant hardened sense amplifiers, the SRAM can achieve high reliability with low speed and area overhead

Study of Radiation Tolerant Storage Cells for Digital Systems

Single event upsets (SEUs) are a significant reliability issue in semiconductor devices. Fully Depleted Silicon-on-Insulator (FDSOI) technologies have been shown to exhibit better SEU performance compared to bulk technologies. This is attributed to the thin Silicon (Si) layer on top of a Buried Oxide (BOX) layer, which allows each transistor to function as an insulated Si island, thus reducing the threat of charge-sharing. Moreover, the small volume of the Si in FDSOI devices results in a reduction of the amount of charge induced by an ion strike. The effects of Total Ionizing Dose (TID) on integrated circuits (ICs) can lead to changes in gate propagation delays, leakage currents, and device functionality. When IC circuits are exposed to ionizing radiation, positive charges accumulate in the gate oxide and field oxide layers, which results in reduced gate control and increased leakage current. TID effects in bulk technologies are usually simpler due to the presence of only one gate oxide layer, but FDSOI technologies have a more complex response to TID effects because of the additional BOX layer. In this research, we aim to address the challenges of developing cost-effective electronics for space applications by bridging the gap between expensive space-qualified components and high-performance commercial technologies. Key research questions involve exploring various radiation-hardening-by-design (RHBD) techniques and their trade-offs, as well as investigating the feasibility of radiation-hardened microcontrollers. The effectiveness of RHBD techniques in mitigating soft errors is well-established. In our study, a test chip was designed using the 22-nm FDSOI process, incorporating multiple RHBD Flip-Flop (FF) chains alongside a conventional FF chain. Three distinct types of ring oscillators (ROs) and a 256 kbit SRAM was also fabricated in the test chip. To evaluate the SEU and TID performance of these designs, we conducted multiple irradiation experiments with alpha particles, heavy ions, and gamma-rays. Alpha particle irradiation tests were carried out at the University of Saskatchewan using an Americium-241 alpha source. Heavy ion experiments were performed at the Texas A&M University Cyclotron Institute, utilizing Ne, Ar, Cu, and Ag in a 15 MeV/amu cocktail. Lastly, TID experiments were conducted using a Gammacell 220 Co-60 chamber at the University of Saskatchewan. By evaluating the performance of these designs under various irradiation conditions, we strive to advance the development of cost-effective, high-performance electronics suitable for space applications, ultimately demonstrating the significance of this project. When exposed to heavy ions, radiation-hardened FFs demonstrated varying levels of improvement in SEU performance, albeit with added power and timing penalties compared to conventional designs. Stacked-transistor DFF designs showed significant enhancement, while charge-cancelling and interleaving techniques further reduced upsets. Guard-gate (GG) based FF designs provided additional SEU protection, with the DFR-FF and GG-DICE FF designs showing zero upsets under all test conditions. Schmitt-trigger-based DFF designs exhibited improved SEU performance, making them attractive choices for hardening applications. The 22-nm FDSOI process proved more resilient to TID effects than the 28-nm process; however, TID effects remained prominent, with increased leakage current and SRAM block degradation at high doses. These findings offer valuable insights for designers aiming to meet performance and SER specifications for circuits in radiation environments, emphasizing the need for additional attention during the design phase for complex radiation-hardened circuits

A Timing-Monitoring Sequential for Forward and Backward Error-Detection in 28 nm FD-SOI

The increasing impact of variability on near-threshold nanometer circuits calls for a tighter online monitoring and control of the available timing margins. Error-detection sequentials are widely used together with error-correction techniques to operate digital designs with such carefully controlled far-below-worst-case margins, ensuring their correct operation even in the presence of uncertainties and variations. However, these registers are often designed only to either detect setup timing violations or to measure the available positive timing slack for a small detection-window. In this paper we propose a timing-monitoring sequential that provides both timing-monitoring modes, which can be selected at run-time depending on the desired timing-monitoring strategy. As the detection window of the presented circuit depends on the duty-cycle of the clock, either slow paths or fast paths can be monitored and measured with wide timing windows. The performance of this timing-monitoring sequential is evaluated in a 28nm FD-SOI process with post-layout simulations which show that the circuit is able to monitor a positive timing slack as small as 140 ps or to measure a path delay as fast as 50 ps. The proposed circuit is applied to a digital multiplier that was fabricated in a test chip and measurements show that the timing-monitoring sequentials are able to measure the critical path of the multiplier with a 1% accuracy and without incurring any timing violation

Radiation Tolerant Electronics, Volume II

Research on radiation tolerant electronics has increased rapidly over the last few years, resulting in many interesting approaches to model radiation effects and design radiation hardened integrated circuits and embedded systems. This research is strongly driven by the growing need for radiation hardened electronics for space applications, high-energy physics experiments such as those on the large hadron collider at CERN, and many terrestrial nuclear applications, including nuclear energy and safety management. With the progressive scaling of integrated circuit technologies and the growing complexity of electronic systems, their ionizing radiation susceptibility has raised many exciting challenges, which are expected to drive research in the coming decade.After the success of the first Special Issue on Radiation Tolerant Electronics, the current Special Issue features thirteen articles highlighting recent breakthroughs in radiation tolerant integrated circuit design, fault tolerance in FPGAs, radiation effects in semiconductor materials and advanced IC technologies and modelling of radiation effects

Low-Power Design of Digital VLSI Circuits around the Point of First Failure

As an increase of intelligent and self-powered devices is forecasted for our future everyday life, the implementation of energy-autonomous devices that can wirelessly communicate data from sensors is crucial. Even though techniques such as voltage scaling proved to effectively reduce the energy consumption of digital circuits, additional energy savings are still required for a longer battery life. One of the main limitations of essentially any low-energy technique is the potential degradation of the quality of service (QoS). Thus, a thorough understanding of how circuits behave when operated around the point of first failure (PoFF) is key for the effective application of conventional energy-efficient methods as well as for the development of future low-energy techniques. In this thesis, a variety of circuits, techniques, and tools is described to reduce the energy consumption in digital systems when operated either in the safe and conservative exact region, close to the PoFF, or even inside the inexact region. A straightforward approach to reduce the power consumed by clock distribution while safely operating in the exact region is dual-edge-triggered (DET) clocking. However, the DET approach is rarely taken, primarily due to the perceived complexity of its integration. In this thesis, a fully automated design flow is introduced for applying DET clocking to a conventional single-edge-triggered (SET) design. In addition, the first static true-single-phase-clock DET flip-flop (DET-FF) that completely avoids clock-overlap hazards of DET registers is proposed. Even though the correct timing of synchronous circuits is ensured in worst-case conditions, the critical path might not always be excited. Thus, dynamic clock adjustment (DCA) has been proposed to trim any available dynamic timing margin by changing the operating clock frequency at runtime. This thesis describes a dynamically-adjustable clock generator (DCG) capable of modifying the period of the produced clock signal on a cycle-by-cycle basis that enables the DCA technique. In addition, a timing-monitoring sequential (TMS) that detects input transitions on either one of the clock phases to enable the selection of the best timing-monitoring strategy at runtime is proposed. Energy-quality scaling techniques aimat trading lower energy consumption for a small degradation on the QoS whenever approximations can be tolerated. In this thesis, a low-power methodology for the perturbation of baseline coefficients in reconfigurable finite impulse response (FIR) filters is proposed. The baseline coefficients are optimized to reduce the switching activity of the multipliers in the FIR filter, enabling the possibility of scaling the power consumption of the filter at runtime. The area as well as the leakage power of many system-on-chips is often dominated by embedded memories. Gain-cell embedded DRAM (GC-eDRAM) is a compact, low-power and CMOS-compatible alternative to the conventional static random-access memory (SRAM) when a higher memory density is desired. However, due to GC-eDRAMs relying on many interdependent variables, the adaptation of existing memories and the design of future GCeDRAMs prove to be highly complex tasks. Thus, the first modeling tool that estimates timing, memory availability, bandwidth, and area of GC-eDRAMs for a fast exploration of their design space is proposed in this thesis

Dependable Embedded Systems

This Open Access book introduces readers to many new techniques for enhancing and optimizing reliability in embedded systems, which have emerged particularly within the last five years. This book introduces the most prominent reliability concerns from today’s points of view and roughly recapitulates the progress in the community so far. Unlike other books that focus on a single abstraction level such circuit level or system level alone, the focus of this book is to deal with the different reliability challenges across different levels starting from the physical level all the way to the system level (cross-layer approaches). The book aims at demonstrating how new hardware/software co-design solution can be proposed to ef-fectively mitigate reliability degradation such as transistor aging, processor variation, temperature effects, soft errors, etc. Provides readers with latest insights into novel, cross-layer methods and models with respect to dependability of embedded systems; Describes cross-layer approaches that can leverage reliability through techniques that are pro-actively designed with respect to techniques at other layers; Explains run-time adaptation and concepts/means of self-organization, in order to achieve error resiliency in complex, future many core systems

耐ソフトエラーラッチにおける欠陥の分析、検出及び評価に関する研究

The development of modern integrated circuits (ICs) has greatly changed the life of humankind. Nowadays, IC s are also indispensable to mission-critical applications, such as medical devices, autonomous cars, aircraft navigating systems, and satellites. The reliability of these mission-critical applications is a major concern. A soft-error occurring in an IC is a severe threat to its reliability, especially for mission-critical applications. The continuous trend of shrinking technology feature sizes makes modern ICs more and more vulnerable to soft errors. Soft-errors are caused by radiation particles striking an IC and generating current pulses to disturb its functionality. A soft-error can cause data corruption and may eventually lead to system failure s If a soft-error occurs in an operational medical device during surgery, it may cause a malfunction of this device and interrupt the surgery process. A soft-error may change the control data of an autonomous car which may lead to an accident. A soft-error may corrupt the aircraft navigating systems. No one would take the chance to let it happen even though malfunction s caused by soft errors can be solved by resetting these devices. Because reset takes time and severe results may happen during the resetting. If a soft-error causes a malfunction in the control system of a satellite, it may not be able to maintain its height and eventually burn up as it falls into the Earth’s atmosphere. Hence, it is important to protect ICs from soft errors. Many soft-error tolerance methods have been proposed to protect ICs against soft-errors. In an IC, memory elements and storage elements (e.g., latches and flip flops) are the most vulnerable to soft-errors, and data stored in them are crucial to the operation of a circuit. Error correction codes (ECCs) can be u sed to protect memories. Register-level soft-error tolerance methods can be used to detect soft-errors in latches by using parity checking and correct them by resetting. Hardened designs protect latches against soft-errors by using redundant feedback loops to store the same input data and using a voter to select the correct output. The advantage of using hardened designs is that they can prevent soft-errors from reaching outputs while ECCs and register-level soft-error tolerance methods must detect soft-errors and then correct them by restoring the data. For protecting storage elements in mission-critical applications, hardened latch design is the best option because it has high reliability and can save the resetting time. Many state-of-the-art hardened latch designs have been proposed to tolerate soft errors and they are believed to have good soft-error tolerability. Defects (physical flaws due to imperfect production (production defects) and physical changes caused by aging effects after a long operation time (aging-related defects) can also cause a malfunction of a circuit and cause a system failure eventually. Different from the temporal state change of a circuit caused by soft errors, defects are permanent damages to a circuit and can disturb the behavior of a circuit from its desired manner. Defects in storage elements should be detected to make sure a system/device operating correctly and stably. Scan test is a commonly used defect detection method, which connects reconfigured storage elements to form a shift register with external access and the internal states of these storage elements can be easily controlled and checked. However, the impact of defects on existing state of the art hardened latch design has not been considered. This impact requires consideration because added redundancy in hardened latch designs can not only mask soft-errors but also mask the effects of defects and it can lead to two serious problems: Problem-1 (Low Testability): Production defects in hardened latch designs are difficult to detect with conventional scan tests, in which the observability (an important metric to evaluate a circuit’s testability) of defects in hardened latch designs can be greatly reduced. Therefore, existing state-of-the-art hardened latches have low observability and thus low testability. Furthermore, defects that escaped the production test (undetected defects) may become more and more serious and cause a system failure eventually. Problem-2 (Low Soft-Error Tolerability): Undetected defects and aging-related defects can make hardened latch designs vulnerable to soft-errors while defect-free ones do not. The soft-error tolerability of hardened latch designs may be compromise d by undetected defects or aging related defects. This research is the first to consider Problem-1 of low testability of hardened latches and Problem-2 of defects reducing the reliability of hardened latches. Furthermore, this research is the first to pro pose a comprehensive solution to solve these two problems with the following five major contributions: Contribution-1: A first of its kind metric for quantifying the impact of defects on hardened latches, called Post-Test Vulnerability Factor (PTVF). It is used to analyze the residual soft-error tolerability of hardened latches after testing. Problem-2 is solved by this first major contribution. Contribution-2: A novel design called Scan-Test-Aware Hardened Latch (STAHL) that provides the highest defect coverage in comparison with all existing hardened latches. Problem-1 is solved by using STAHL to build a scan c ell to perform a scan test. Contribution-3: A novel scan test procedure is proposed to solve Problem-1 by fully testing the STAHL based scan cell. Contribution-4: A novel High-Performance Scan-Test-Aware Hardened Latch (HP-STAHL) design can also solve Problem-1 and has similar defect coverage as STAHL but has lower power consumption and higher propagation speed. Contribution-5: A novel scan test procedure is proposed to fully test the HP STAHL-based scan cell to solve Problem-1. Comprehensive simulation results demonstrate the accuracy of the PTVF metric and the effectiveness of the STAHL-based scan test and HP-STAHL-based scan test. As the first comprehensive study bridging the gap between hardened latch design s and IC testing, the findings of this research are expected to significantly improve the soft-error-related reliability of IC designs for mission-critical applications. Furthermore, the two proposed hardened latches and the scan test procedures can not only be use d to detect defects after production but also can be applied to detect aging related defects in the field through performing built-in self-test (BIST). In Chapter 1, an example is introduced to indicate Problem-1 and Problem-2. Chapter 2 shows the background information of soft-errors and defects. Chapter 3 shows some typical soft-error mitigation methods and details of a scan test. Chapter 4 describes the detailed information of PTVF Contribution-1). Chapter 5 shows the structure of STAHL (Contribution-2) and Chapter 6 shows the scan test procedure of testing the STAHL-based scan cell (Contribution-3). Chapter 7 shows the structure of HP-STAHL (Contribution-4) and Chapter 8 shows the scan test procedure of testing the HP-STAHL based scan cell (Contribution-5). Chapter 9 shows the experimental results of comparing STAHL and HP-STAHL with state-of-the-art hardened latch designs. Chapter 10 concludes this thesis.九州工業大学博士学位論文 学位記番号：情工博甲第371号 学位授与年月日：令和4年9月26日1. Introduction|2. Background|3. Related Works|4. Post-Test Vulnerability Factor (PTVF)|5. Scan-Test Aware Hardened Latch (STAHL)|6. Scan Test Based on STAHL|7. High Performance Scan-Test-Aware Hardened Latch (HP STAHL)|8. Scan Test Based on HP STAHL|9. Experimental Evaluation|10. Conclusions and Future Works九州工業大学令和4年

Monitor amb control strategies to reduce the impact of process variations in digital circuits

As CMOS technology scales down, Process, Voltage, Temperature and Ageing (PVTA) variations have an increasing impact on the performance and power consumption of electronic devices. These issues may hold back the continuous improvement of these devices in the near future. There are several ways to face the variability problem: to increase the operating margins of maximum clock frequency, the implementation of lithographic friendly layout styles, and the last one and the focus of this thesis, to adapt the circuit to its actual manufacturing and environment conditions by tuning some of the adjustable parameters once the circuit has been manufactured. The main challenge of this thesis is to develop a low-area variability compensation mechanism to automatically mitigate PVTA variations in run-time, i.e. while integrated circuit is running. This implies the development of a sensor to obtain the most accurate picture of variability, and the implementation of a control block to knob some of the electrical parameters of the circuit.A mesura que la tecnologia CMOS escala, les variacions de Procés, Voltatge, Temperatura i Envelliment (PVTA) tenen un impacte creixent en el rendiment i el consum de potència dels dispositius electrònics. Aquesta problemàtica podria arribar a frenar la millora contínua d'aquests dispositius en un futur proper. Hi ha diverses maneres d'afrontar el problema de la variabilitat: relaxar el marge de la freqüència màxima d'operació, implementar dissenys físics de xips més fàcils de litografiar, i per últim i com a tema principal d'aquesta tesi, adaptar el xip a les condicions de fabricació i d'entorn mitjançant la modificació d'algun dels seus paràmetres ajustables una vegada el circuit ja ha estat fabricat. El principal repte d'aquesta tesi és desenvolupar un mecanisme de compensació de variabilitat per tal de mitigar les variacions PVTA de manera automàtica en temps d'execució, és a dir, mentre el xip està funcionant. Això implica el desenvolupament d'un sensor capaç de mesurar la variabilitat de la manera més acurada possible, i la implementació d'un bloc de control que permeti l'ajust d'alguns dels paràmetres elèctrics dels circuits