Programmable rate modem utilizing digital signal processing techniques

The engineering development study to follow was written to address the need for a Programmable Rate Digital Satellite Modem capable of supporting both burst and continuous transmission modes with either binary phase shift keying (BPSK) or quadrature phase shift keying (QPSK) modulation. The preferred implementation technique is an all digital one which utilizes as much digital signal processing (DSP) as possible. Here design tradeoffs in each portion of the modulator and demodulator subsystem are outlined, and viable circuit approaches which are easily repeatable, have low implementation losses and have low production costs are identified. The research involved for this study was divided into nine technical papers, each addressing a significant region of concern in a variable rate modem design. Trivial portions and basic support logic designs surrounding the nine major modem blocks were omitted. In brief, the nine topic areas were: (1) Transmit Data Filtering; (2) Transmit Clock Generation; (3) Carrier Synthesizer; (4) Receive AGC; (5) Receive Data Filtering; (6) RF Oscillator Phase Noise; (7) Receive Carrier Selectivity; (8) Carrier Recovery; and (9) Timing Recovery

JamLab: Augmenting Sensornet Testbeds with Realistic and Controlled Interference Generation

Radio interference drastically affects the performance of sensor-net communications, leading to packet loss and reduced energy-efficiency. As an increasing number of wireless devices operates on the same ISM frequencies, there is a strong need for understanding and debugging the performance of existing sensornet protocols under interference. Doing so requires a low-cost flexible testbed infrastructure that allows the repeatable generation of a wide range of interference patterns. Unfortunately, to date, existing sensornet testbeds lack such capabilities, and do not permit to study easily the coexistence problems between devices sharing the same frequencies. This paper addresses the current lack of such an infrastructure by using off-the-shelf sensor motes to record and playback interference patterns as well as to generate customizable and repeat-able interference in real-time. We propose and develop JamLab: a low-cost infrastructure to augment existing sensornet testbeds with accurate interference generation while limiting the overhead to a simple upload of the appropriate software. We explain how we tackle the hardware limitations and get an accurate measurement and regeneration of interference, and we experimentally evaluate the accuracy of JamLab with respect to time, space, and intensity. We further use JamLab to characterize the impact of interference on sensornet MAC protocols

Replacing the automatic gain control loop in a mobile, digital TV broadcast receiver by a software based solution

The power level (the amplitude) of an electro-magnetic signal wave suffers from attenuation the greater the distance between the transmitter and the receiver is. The receiver of that signal therefore has components which try to amplify the signal so that it can be processed optimally by a processor. In a mobile or portable environment the signal power level can vary strongly, because the position of the receiver to the transmitter is not fixed. In order to compensate that movement a control loop exists, which dynamically is adapting the front-end to the right level. This work describes a new, software-based way to handle the signal level control loop (formerly automatic gain control) in a digital TV receiver. Starting with a very basic introduction into digital communications, including the description of the traditional front-end architecture, followed by a detailed description of the new method. Finally some conclusions of this new method are made which are giving an idea about how in the future it might be possible to reach better receiving performances using this mechanism

Theory of phaselock techniques as applied to aerospace transponders

Phaselock techniques as applied to aerospace transponder

Estudio y diseño de dos placas de intercambio de datos de inclinación y posición entre dos cubesats

El grupo de investigación DISEN con sede en el Campus de Terrassa de la UPC está intentando impulsar el proyecto de la implementación de una infraestructura de comunicaciones basada en el enlace óptico de CubeSats. Mediante este tipo de comunicación, se podría obtener un mayor data-rate y un menor consumo de potencia que en los actuales sistemas de radiofrecuencia. Para poder realizar este enlace óptico, es necesario que el rayo láser proveniente de uno de los satélites se centre de forma muy precisa en el foto-detector del otro satélite. Para realizar dicho centrado, ambos satélites deberán conocer a priori la posición e inclinación de ambos, información que deberán intercambiarse mediante radiofrecuencia. El presente TFG versa sobre el diseño del subsistema de intercambio de datos de posición e inclinación entre dos CubeSats. Concretamente, el diseño de dos placas PCB formadas por un módulo GPS, para obtener la posición de los CubeSats; un módulo IMU, para obtener sus actitudes; un módulo de radio UHF, para enviar datos entre los dos CubeSats por radiofrecuencia; y un módulo Bluetooth para poder enlazar el sistema con el ordenador de base. Además, las placas cuentan con un microcontrolador para procesar y almacenar la información de dichos módulos

Hardware simulation of KU-band spacecraft receiver and bit synchronizer, phase 2, volume 1

The acquisition behavior of the PN subsystem of an automatically acquiring spacecraft receiver was studied. A symbol synchronizer subsystem was constructed and integrated into the composite simulation of the receiver. The overall performance of the receiver when subjected to anomalies such as signal fades was evaluated. Potential problems associated with PN/carrier sweep interactions were investigated

A fully integrated RSSI and an ultra-low power SAR ADC for 5.8 GHz DSRC ETC transceiver

This study presents a monolithic received signal strength indicator (RSSI) and an ultra-low power SAR ADC for 5.8 GHz DSRC transceiver in China electronic toll collection systems. In order to meet the stringent requirement of wide input range for the transceiver, two RSSIs collaborate with auxiliary ADC circuits to provide the digitalized received signal strength to the digital baseband of a transceiver. The RSSI design achieves fast transient response and low power consumption with a small die area by using internal active low-pass filters instead of external passive ones. The proposed design has been fabricated using a 0.13 μm 2P6M CMOS technology. Measurement results show that the overall input dynamic range is 86 dB with an accuracy of ±1.72 dB and a transient response of less than 2 μs. Compared with the state-of-the-art designs in the literature, the overall input range and transient settling time are improved by at least 14.6%, and 300%, respectively

A study of bistatic radar and the development of an independent bistatic radar receiver

Bibliography: pages 120-121.This report contains a literature review of bistatic radar and also describes an experimental L-Band bistatic radar receiver which was built at the University of Cape Town. In a bistatic radar the transmitter and receiver are separated by an amount which is comparable to the distance to the targets which are being displayed. The separation of the transmitter and receiver cause various parameters to change when comparing the bistatic radar to a monostatic radar

Joint University Program for Air Transportation Research, 1981

Navigation, guidance, control and display concepts, and hardware, with special emphasis on applications to general aviation aircraft are discussed