Noise shaping Asynchronous SAR ADC based time to digital converter

Time-to-digital converters (TDCs) are key elements for the digitization of timing information in modern mixed-signal circuits such as digital PLLs, DLLs, ADCs, and on-chip jitter-monitoring circuits. Especially, high-resolution TDCs are increasingly employed in on-chip timing tests, such as jitter and clock skew measurements, as advanced fabrication technologies allow fine on-chip time resolutions. Its main purpose is to quantize the time interval of a pulse signal or the time interval between the rising edges of two clock signals. Similarly to ADCs, the performance of TDCs are also primarily characterized by Resolution, Sampling Rate, FOM, SNDR, Dynamic Range and DNL/INL. This work proposes and demonstrates 2nd order noise shaping Asynchronous SAR ADC based TDC architecture with highest resolution of 0.25 ps among current state of art designs with respect to post-layout simulation results. This circuit is a combination of low power/High Resolution 2nd Order Noise Shaped Asynchronous SAR ADC backend with simple Time to Amplitude converter (TAC) front-end and is implemented in 40nm CMOS technology. Additionally, special emphasis is given on the discussion on various current state of art TDC architectures.Electrical and Computer Engineerin

An Offset Cancelation Technique for Latch Type Sense Amplifiers

An offset compensation technique for a latch type sense amplifier is proposed in this paper. The proposed scheme is based on the recalibration of the charging/discharging current of the critical nodes which are affected by the device mismatches. The circuit has been designed in a 65 nm CMOS technology with 1.2 V core transistors. The auto-calibration procedure is fully digital. Simulation results are given verifying the operation for sampling a 5 Gb/s signal dissipating only 360 uW

An affordable multichannel potentiostat with 128 individual stimulation and sensing channels

(Bio)electrochemical reactions are a promising, environmentally friendly alternative for many chemical processes. These processes, however, are known to be slow in time, to be strongly dependent on the environment and to vary between different samples. This necessitates research on studying optimal operating conditions of the (bio)electrochemical cells. Yet, current experiments have to rely on slow, sequential tests. To overcome these, this work proposes a potentiostat with 128 parallel channels to speed up research experiments. The 128-channel potentiostat makes extensive use of time-sharing and is implemented with PCB technology resulting in a cost-per-channel of only 5$, 4x lower than the state-of-the-art (SotA) and an area-per-channel of ≈ 93 mm 2 , 5x lower than the SotA. Realtime digital compensation of each individual channel is used to obtain a channel-to-channel mismatch below 1%. A cyclic voltametry experiment on all channels simultaneously illustrates the low channel-to-channel mismatch. A chronoamperometry experiment with 128 different potential steps in parallel illustrates the 128x experiment speedup

An Overview of Charge Pump for Phase Lock Loop System for High Frequency Application.

Phase lock loop is fundamental buliding block of modern communication system. Phase lock loop are typically used to provide local oscillator function in radio reciver or transmitter. The design methodology and test result of charge pump structure for phase lock loop application are presented. The structure is composed to two charge/ discharge block. This paper provides study of various charge pump and discuss the technology that is used to design charge pump

Process and Temperature Compensated Wideband Injection Locked Frequency Dividers and their Application to Low-Power 2.4-GHz Frequency Synthesizers

There has been a dramatic increase in wireless awareness among the user community in the past five years. The 2.4-GHz Industrial, Scientific and Medical (ISM) band is being used for a diverse range of applications due to the following reasons. It is the only unlicensed band approved worldwide and it offers more bandwidth and supports higher data rates compared to the 915-MHz ISM band. The power consumption of devices utilizing the 2.4-GHz band is much lower compared to the 5.2-GHz ISM band. Protocols like Bluetooth and Zigbee that utilize the 2.4-GHz ISM band are becoming extremely popular. Bluetooth is an economic wireless solution for short range connectivity between PC, cell phones, PDAs, Laptops etc. The Zigbee protocol is a wireless technology that was developed as an open global standard to address the unique needs of low-cost, lowpower, wireless sensor networks. Wireless sensor networks are becoming ubiquitous, especially after the recent terrorist activities. Sensors are employed in strategic locations for real-time environmental monitoring, where they collect and transmit data frequently to a nearby terminal. The devices operating in this band are usually compact and battery powered. To enhance battery life and avoid the cumbersome task of battery replacement, the devices used should consume extremely low power. Also, to meet the growing demands cost and sized has to be kept low which mandates fully monolithic implementation using low cost process. CMOS process is extremely attractive for such applications because of its low cost and the possibility to integrate baseband and high frequency circuits on the same chip. A fully integrated solution is attractive for low power consumption as it avoids the need for power hungry drivers for driving off-chip components. The transceiver is often the most power hungry block in a wireless communication system. The frequency divider (prescaler) and the voltage controlled oscillator in the transmitter’s frequency synthesizer are among the major sources of power consumption. There have been a number of publications in the past few decades on low-power high-performance VCOs. Therefore this work focuses on prescalers. A class of analog frequency dividers called as Injection-Locked Frequency Dividers (ILFD) was introduced in the recent past as low power frequency division. ILFDs can consume an order of magnitude lower power when compared to conventional flip-flop based dividers. However the range of operation frequency also knows as the locking range is limited. ILFDs can be classified as LC based and Ring based. Though LC based are insensitive to process and temperature variation, they cannot be used for the 2.4-GHz ISM band because of the large size of on-chip inductors at these frequencies. This causes a lot of valuable chip area to be wasted. Ring based ILFDs are compact and provide a low power solution but are extremely sensitive to process and temperature variations. Process and temperature variation can cause ring based ILFD to loose lock in the desired operating band. The goal of this work is to make the ring based ILFDs useful for practical applications. Techniques to extend the locking range of the ILFDs are discussed. A novel and simple compensation technique is devised to compensate the ILFD and keep the locking range tight with process and temperature variations. The proposed ILFD is used in a 2.4-GHz frequency synthesizer that is optimized for fractional-N synthesis. Measurement results supporting the theory are provided

Self-powered Time-Keeping and Time-of-Occurrence Sensing

Self-powered and passive Internet-of-Things (IoT) devices (e.g. RFID tags, financial assets, wireless sensors and surface-mount devices) have been widely deployed in our everyday and industrial applications. While diverse functionalities have been implemented in passive systems, the lack of a reference clock limits the design space of such devices used for applications such as time-stamping sensing, recording and dynamic authentication. Self-powered time-keeping in passive systems has been challenging because they do not have access to continuous power sources. While energy transducers can harvest power from ambient environment, the intermittent power cannot support continuous operation for reference clocks. The thesis of this dissertation is to implement self-powered time-keeping devices on standard CMOS processes. In this dissertation, a novel device that combines the physics of quantum tunneling and floating-gate (FG) structures is proposed for self-powered time-keeping in CMOS process. The proposed device is based on thermally assisted Fowler-Nordheim (FN) tunneling process across high-quality oxide layer to discharge the floating-gate node, therefore resulting in a time-dependent FG potential. The device was fully characterized in this dissertation, and it does not require external powering during runtime, making it feasible for passive devices and systems. Dynamic signature based on the synchronization and desynchronization behavior of the FN timer is proposed for authentication of IoT devices. The self-compensating physics ensure that when distributed timers are subjected to identical environment variances that are common-mode noise, they can maintain synchronization with respect to each other. On the contrary, different environment conditions will desynchronize the timers creating unique signatures. The signatures could be used to differentiate between products that belong to different supply-chains or products that were subjected to malicious tampering. SecureID type dynamic authentication protocols based on the signature generated by the FN timers are proposed and they are proven to be robust to most attacks. The protocols are further analyzed to be lightweight enough for passive devices whose computational sources are limited. The device could also be applied for self-powered sensing of time-of-occurrence. The prototype was verified by integrating the device with a self-powered mechanical sensor to sense and record time-of-occurrence of mechanical events. The system-on-chip design uses the timer output to modulate a linear injector to stamp the time information into the sensing results. Time-of-occurrence can be reconstructed by training the mathematical model and then applying that to the test data. The design was verified to have a high reconstruction accuracy

Ultra-Low-Voltage IC Design Methods

The emerging nanoscale technologies inherently offer transistors working with low voltage levels and are optimized for low-power operation. However, these technologies lack quality electronic components vital for reliable analog and/or mixed-signal design (e.g., resistor, capacitor, etc.) as they are predominantly used in high-performance digital designs. Moreover, the voltage headroom, ESD properties, the maximum current densities, parasitic effects, process fluctuations, aging effects, and many other parameters are superior in verified-by-time CMOS processes using planar transistors. This is the main reason, why low-voltage, low-power high-performance analog and mixed-signal circuits are still being designed in mature process nodes. In the proposed chapter, we bring an overview of main challenges and design techniques effectively applicable for ultra-low-voltage and low-power analog integrated circuits in nanoscale technologies. New design challenges and limitations linked with a low value of the supply voltage, the process fluctuation, device mismatch, and other effects are discussed. In the later part of the chapter, conventional and unconventional design techniques (bulk-driven approach, floating-gate, dynamic threshold, etc.) to design analog integrated circuits towards ultra-low-voltage systems and applications are described. Examples of ultra-low-voltage analog ICs blocks (an operational amplifier, a voltage comparator, a charge pump, etc.) designed in a standard CMOS technology using the unconventional design approach are presented

A Wide Range and High Swing Charge Pump for Phase Locked Loop in Phasor Measurement Unit

© 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works. Phasor Measurement Units are widely utilized in power systems to provide synchrophasor data for a verity of applications, mainly performed by Energy Management Systems (EMS). Synchrophasors are measured at different parts of the network and transmitted to Phasor Data Concentrator (PDC) at a rate of 30-60 samples per second. The synchronization is done by means of a phase locked oscillator inside PMU which uses clock signal of the Global Positioning System (GPS). In this paper a novel charge pump with an appropriate operation capability in phaselocked-loops is presented. By using this phase locked loop in phasor measurement unit, the total performance of this circuit will be improved. The proposed charge pump uses current mirror techniques in order to achieve a wide range of output voltage to control the oscillator and also has a good performance in a wide frequency range from 33MHz to 555MHz. This circuit is designed and simulated in TSMC 0.18μm CMOS technology. The proposed charge pump only consumes 390μW power in supply voltage of 1.8V at 500MHz and has a maximum current of 16.43μA with an acceptable current matching between source and sink currents. It is also capable to be used in a wide frequency range and low power applications

Ultra-low Quiescent Current NMOS Low Dropout Regulator With Fast Transient response for Always-On Internet-of-Things Applications

abstract: The increased adoption of Internet-of-Things (IoT) for various applications like smart home, industrial automation, connected vehicles, medical instrumentation, etc. has resulted in a large scale distributed network of sensors, accompanied by their power supply regulator modules, control and data transfer circuitry. Depending on the application, the sensor location can be virtually anywhere and therefore they are typically powered by a localized battery. To ensure long battery-life without replacement, the power consumption of the sensor nodes, the supply regulator and, control and data transmission unit, needs to be very low. Reduction in power consumption in the sensor, control and data transmission is typically done by duty-cycled operation such that they are on periodically only for short bursts of time or turn on only based on a trigger event and are otherwise powered down. These approaches reduce their power consumption significantly and therefore the overall system power is dominated by the consumption in the always-on supply regulator. Besides having low power consumption, supply regulators for such IoT systems also need to have fast transient response to load current changes during a duty-cycled operation. Supply regulation using low quiescent current low dropout (LDO) regulators helps in extending the battery life of such power aware always-on applications with very long standby time. To serve as a supply regulator for such applications, a 1.24 µA quiescent current NMOS low dropout (LDO) is presented in this dissertation. This LDO uses a hybrid bias current generator (HBCG) to boost its bias current and improve the transient response. A scalable bias-current error amplifier with an on-demand buffer drives the NMOS pass device. The error amplifier is powered with an integrated dynamic frequency charge pump to ensure low dropout voltage. A low-power relaxation oscillator (LPRO) generates the charge pump clocks. Switched-capacitor pole tracking (SCPT) compensation scheme is proposed to ensure stability up to maximum load current of 150 mA for a low-ESR output capacitor range of 1 - 47µF. Designed in a 0.25 µm CMOS process, the LDO has an output voltage range of 1V – 3V, a dropout voltage of 240 mV, and a core area of 0.11 mm2.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201