A Low Power Integrated Circuit for Implantable Biosensor Incorporating an On-Chip FSK Modulator

Medical care has been significantly improved in recent years due to tremendous technological advancement in the field of CMOS technology. Among those improvements, integrated circuit design and sensing techniques have brought to the doctors more flexibility and accuracy of examinations of their patients. For example, a diabetic patient needs to visit a hospital on a regular basis for the examination and proper treatment. However, with the tremendous advancement in electronic technology, a patient can soon monitor his or her own blood glucose level at home or at office with an implantable sensor which can also trigger insulin pump attached to the body. The insulin delivery system can be precisely controlled by the electronics embedded in the implantable device. In this thesis, a low power integrated circuit for the implantable biosensor incorporating an on-chip FSK modulator is presented. This design has been fabricated using AMI 0.5-μm CMOS process available through MOSIS. The simulation and test results are also presented to verify its operation

High-speed communication circuits: voltage control oscillators and VCO-derived filters

Voltage Controlled Oscillators (VCO) and filters are the two main topics of focus in this dissertation.;A temperature and process compensated VCO, which is designed to operate at 2 GHz, and whose frequency variation due to incoming data is limited to 1% of its center frequency was presented. The test results show that, without process changes present, the frequency variation due to a temperature change over 0°C to 100°C is around 1.1% of its center frequency. This is a reduction of a factor of 10 when compared to the temperature variation of a conventional VCO.;A new method of designing continuous-time monolithic filters derived from well-known voltage controlled oscillators (VCOs) was introduced. These VCO-derived filters are capable of operating at very high frequencies in standard CMOS processes. Prototype low-pass and band-pass filters designed in a TSMC 0.25 mum process are discussed. Simulation results for the low-pass filter designed for a cutoff frequency of 4.3 GHz show a THD of -40 dB for a 200 mV peak-peak sinusoidal input. The band-pass filter has a resonant frequency programmable from 2.3 GHz to 3.1 GHz, a programmable Q from 3 to 85, and mid-band THD of -40 dB for an 80 mV peak-peak sinusoidal input signal.;A third contribution in this dissertation was the design of a new current mirror with accurate mirror gain for low beta bipolar transistors. High mirror gain accuracy is achieved by using a split-collector transistor to compensate for base currents of the source-coupled

Electronic control circuits: A compilation

A compilation of technical R and D information on circuits and modular subassemblies is presented as a part of a technology utilization program. Fundamental design principles and applications are given. Electronic control circuits discussed include: anti-noise circuit; ground protection device for bioinstrumentation; temperature compensation for operational amplifiers; hybrid gatling capacitor; automatic signal range control; integrated clock-switching control; and precision voltage tolerance detector

Integrated Circuits for Programming Flash Memories in Portable Applications

Smart devices such as smart grids, smart home devices, etc. are infrastructure systems that connect the world around us more than before. These devices can communicate with each other and help us manage our environment. This concept is called the Internet of Things (IoT). Not many smart nodes exist that are both low-power and programmable. Floating-gate (FG) transistors could be used to create adaptive sensor nodes by providing programmable bias currents. FG transistors are mostly used in digital applications like Flash memories. However, FG transistors can be used in analog applications, too. Unfortunately, due to the expensive infrastructure required for programming these transistors, they have not been economical to be used in portable applications. In this work, we present low-power approaches to programming FG transistors which make them a good candidate to be employed in future wireless sensor nodes and portable systems. First, we focus on the design of low-power circuits which can be used in programming the FG transistors such as high-voltage charge pumps, low-drop-out regulators, and voltage reference cells. Then, to achieve the goal of reducing the power consumption in programmable sensor nodes and reducing the programming infrastructure, we present a method to program FG transistors using negative voltages. We also present charge-pump structures to generate the necessary negative voltages for programming in this new configuration

UHF Power Transmission for Passive Sensor Transponders

Passive transponder tags operating in the ultra high frequency (UHF) range receive their power supply from the electromagnetic carrier wave from a remote base station. The maximum range is largely determined by the circuits’ current consumption and the rectifier efficiency. Reading ranges of several meters have recently been reported for several state of the art RFID (Radio frequency IDentification) tags [1]. The presented UHF transponder chip with integrated temperature sensor was designed for a 0.35 ?m CMOS process with EEPROM, Schottky diodes, and double poly layers. Due to a more complex architecture and additional functionality, the power consumption of the presented sensor transponder tag is significantly larger than that of simple RFID tags. The A/D conversion requires a stable, ripple-free supply voltage with a relatively large DC value. A novel rectifier circuit generates the supply voltage from the high frequency antenna signal. The circuit requires only -11.4 dBm input power and is insensitive to temperature and process variations. The maximum operating distance is approximately 4.5 m

Mixed Signal Integrated Circuit Design for Custom Sensor Interfacing

Low-power analog integrated circuits (ICs) can be utilized at the interface between an analog sensor and a digital system\u27s input to decrease power consumption, increase system accuracy, perform signal processing, and make the necessary adjustments for compatibility between the two devices. This interfacing has typically been done with custom integrated solutions, but advancements in floating-gate technologies have made reconfigurable analog ICs a competitive option. Whether the solution is a custom design or built from a reconfigurable system, digital peripheral circuits are needed to configure their operation for these analog circuits to work with the best accuracy.;Using an analog IC as a front end signal processor between an analog sensor and wireless sensor mote can greatly decrease battery consumption. Processing in the digital domain requires more power than when done on an analog system. An Analog Signal Processor (ASP) can allow the digital wireless mote to remain in sleep mode while the ASP is always listening for an important event. Once this event occurs, the ASP will wake the wireless mote, allowing it to record the event and send radio transmissions if necessary. As most wireless sensor networks employ the use of batteries as a power source, an energy harvesting system in addition to an ASP can be used to further supplement this battery consumption.;This thesis documents the development of mixed-signal integrated circuits for use as interfaces between analog sensors and digital Wireless Sensor Networks (WSNs). The following work outlines, as well as shows the results, of development for sensor interfacing utilizing both custom mixed signal integrated circuits as well as a Field Programmable Analog Array (FPAA) for post fabrication customization. An Analog Signal Processor (ASP) has been used in an Acoustic Vehicle Classification system. To keep these interfacing methods low power, a prototype energy harvesting system using commercial-off-the-shelf (COTS) devices is detailed which has led to the design of a fully integrated solution

Variable Spurious Noise Mitigation Techniques in Hysteretic Buck Converters

This work proposes a current-mode hysteretic buck converter with a spur-free constant-cycle frequency-hopping controller that fully eliminates spurs from the switching noise spectrum irrespective of variations in the switching frequency and operating conditions. As a result, the need for frequency regulation loops to ensure non-varying switching frequency (i.e. fixed spurs location) in hysteretic controllers is eliminated. Moreover, compared to frequency regulation loops, the proposed converter offers the advantage of eliminating mixing and interference altogether due to its spur-free operation, and thus, it can be used to power, or to be integrated within noise-sensitive systems while benefiting from the superior dynamic performance of its hysteretic operation. The proposed converter uses dual-sided hysteretic band modulation to eliminate the inductor current imbalance that results from frequency hopping along with the output voltage transients and low-frequency noise floor peaking associated with it. Moreover, a feedforward adaptive hysteretic band controller is proposed to reduce variations in the switching frequency with the input voltage, and an all-digital soft-startup circuit is proposed to control the in-rush current without requiring any off-chip components. The converter is implemented in a 0.35-õm standard CMOS technology and it achieves 92% peak efficiency

Nanopower CMOS transponders for UHF and microwave RFID systems

At first, we present an analysis and a discussion of the design options and tradeoffs for a passive microwave transponder. We derive a set of criteria for the optimization of the voltage multiplier, the power matching network and the backscatter modulator in order to optimize the operating range. In order to match the strictly power requirements, the communication protocol between transponder and reader has been chosen in a convenient way, in order to make the architecture of the passive transponder very simple and then ultra-low-power. From the circuital point of view, the digital section has been implemented in subthreshold CMOS logic with very low supply voltage and clock frequency. We present different solutions to supply power to the transponder, in order to keep the power consumption in the deep sub-µW regime and to drastically reduce the huge sensitivity of the subthreshold logic to temperature and process variations. Moreover, a low-voltage and low-power EEPROM in a standard CMOS process has been implemented. Finally, we have presented the implementation of the entire passive transponder, operating in the UHF or microwave frequency range

Low jitter phase-locked loop clock synthesis with wide locking range

The fast growing demand of wireless and high speed data communications has driven efforts to increase the levels of integration in many communications applications. Phase noise and timing jitter are important design considerations for these communications applications. The desire for highly complex levels of integration using low cost CMOS technologies works against the minimization of timing jitter and phase noise for communications systems which employ a phase-locked loop for frequency and clock synthesis with on-chip VCO. This dictates an integrated CMOS implementation of the VCO with very low phase noise performance. The ring oscillator VCOs based on differential delay cell chains have been used successfully in communications applications, but thermal noise induced phase noise have to be minimized in order not to limit their applicability to some applications which impose stringent timing jitter and phase noise requirements on the PLL clock synthesizer. Obtaining lower timing jitter and phase noise at the PLL output also requires the minimization of noise in critical circuit design blocks as well as the optimization of the loop bandwidth of the PLL. In this dissertation the fundamental performance limits of CMOS PLL clock synthesizers based on ring oscillator VCOs are investigated. The effect of flicker and thermal noise in MOS transistors on timing jitter and phase noise are explored, with particular emphasis on source coupled NMOS differential delay cells with symmetric load elements. Several new circuit architectures are employed for the charge pump circuit and phase-frequency detector (PFD) to minimize the timing jitter due to the finite dead zone in the PFD and the current mismatch in the charge pump circuit. The selection of the optimum PLL loop bandwidth is critical in determining the phase noise performance at the PLL output. The optimum loop bandwidth and the phase noise performance of the PLL is determined using behavioral simulations. These results are compared with transistor level simulated results and experimental results for the PLL clock synthesizer fabricated in a 0.35 µm CMOS technology with good agreement. To demonstrate the proposed concept, a fully integrated CMOS PLL clock synthesizer utilizing integer-N frequency multiplier technique to synthesize several clock signals in the range of 20-400 MHz with low phase noise was designed. Implemented in a standard 0.35-µm N-well CMOS process technology, the PLL achieves a period jitter of 6.5-ps (rms) and 38-ps (peak-to-peak) at 216 MHz with a phase noise of -120 dBc/Hz at frequency offsets above 10 KHz. The specific research contributions of this work include (1) proposing, designing, and implementing a new charge pump circuit architecture that matches current levels and therefore minimizes one source of phase noise due to fluctuations in the control voltage of the VCO, (2) an improved phase-frequency detector architecture which has improved characteristics in lock condition, (3) an improved ring oscillator VCO with excellent thermal noise induced phase noise characteristics, (4) the application of selfbiased techniques together with fixed bias to CMOS low phase noise PLL clock synthesizer for digital video communications ,and (5) an analytical model that describes the phase noise performance of the proposed VCO and PLL clock synthesizer