270 research outputs found
Efficient offline outer/inner DAC mismatch calibration in wideband ÎÎŁ ADCs
Distortion due to feedback DAC mismatch is a key limitation in Delta Sigma ADCs for wideband wireless communications. This article presents an efficient frequency-domain mask-based offline mismatch calibration method of both the outer DAC and the inner DACs in a Delta Sigma ADC. The test stimulus for the calibration is a two-tone signal near the band edge. To avoid the need for high-performance signal generation, a frequency mask is applied to void the stimulus signal and its phase noise. In this way, the method is robust against distortion and jitter in the stimulus signal, which therefore could be combined from two low-quality signal generators. The two-tone band-edge signal has the additional benefit that the number of needed samples of the excitation signal is very modest because as many intermodulations as possible contribute to the calculation of the mismatch errors of the DACs. Experimental results confirming the calibration method are obtained from a prototype chip, designed for an 85MHz signal bandwidth in 28nm CMOS technology. A two-tone stimulus around 78 MHz is applied to calculate the mismatch of the outer DAC and the inner DAC with only 68K samples. With the DACs calibrated, an SFDR improvement of 28.1 dB is achieved for a single-tone input at 5 MHz, while for a two-tone input around 71 MHz, the IM3 is improved from -63.6 dBc to below the noise floor (<-94.1 dBc). This illustrates the effectiveness of the approach
High Performance Integrated Circuit Blocks for High-IF Wideband Receivers
Due to the demand for highâperformance radio frequency (RF) integrated circuit
design in the past years, a systemâonâchip (SoC) that enables integration of analog and
digital parts on the same die has become the trend of the microelectronics industry. As
a result, a major requirement of the next generation of wireless devices is to support
multiple standards in the same chipâset. This would enable a single device to support
multiple peripheral applications and services.
Based on the aforementioned, the traditional superheterodyne frontâend
architecture is not suitable for such applications as it would require a complete receiver
for each standard to be supported. A more attractive alternative is the highintermediate
frequency (IF) radio architecture. In this case the signal is digitalized at an
intermediate frequency such as 200MHz. As a consequence, the baseband operations,
such as downâconversion and channel filtering, become more power and area efficient
in the digital domain. Such architecture releases the specifications for most of the frontâend building blocks, but the linearity and dynamic range of the ADC become the
bottlenecks in this system. The requirements of large bandwidth, high frequency and
enough resolution make such ADC very difficult to realize. Many ADC architectures
were analyzed and ContinuousâTime Bandpass SigmaâDelta (CTâBPâÎŁÎ) architecture was
found to be the most suitable solution in the highâIF receiver architecture since they
combine oversampling and noise shaping to get fairly high resolution in a limited
bandwidth.
A major issue in continuousâtime networks is the lack of accuracy due to powervoltageâ
temperature (PVT) tolerances that lead to over 20% pole variations compared
to their discreteâtime counterparts. An optimally tuned BP ÎŁÎ ADC requires correcting
for center frequency deviations, excess loop delay, and DAC coefficients. Due to these
undesirable effects, a calibration algorithm is necessary to compensate for these
variations in order to achieve high SNR requirements as technology shrinks.
In this work, a novel linearization technique for a Wideband LowâNoise
Amplifier (LNA) targeted for a frequency range of 3â7GHz is presented. Postâlayout
simulations show NF of 6.3dB, peak S21 of 6.1dB, and peak IIP3 of 21.3dBm,
respectively. The power consumption of the LNA is 5.8mA from 2V.
Secondly, the design of a CMOS 6th order CT BPâÎŁÎ modulator running at 800
MHz for HighâIF conversion of 10MHz bandwidth signals at 200 MHz is presented. A
novel transconductance amplifier has been developed to achieve high linearity and high
dynamic range at high frequencies. A 2âbit quantizer with offset cancellation is alsopresented. The sixthâorder modulator is implemented using 0.18 um TSMC standard
analog CMOS technology. Postâlayout simulations in cadence demonstrate that the
modulator achieves a SNDR of 78 dB (~13 bit) performance over a 14MHz bandwidth.
The modulatorâs static power consumption is 107mW from a supply power of ± 0.9V.
Finally, a calibration technique for the optimization of the Noise Transfer
Function CT BP ÎŁÎ modulators is presented. The proposed technique employs two test
tones applied at the input of the quantizer to evaluate the noise transfer function of
the ADC, using the capabilities of the Digital Signal Processing (DSP) platform usually
available in mixedâmode systems. Once the ADC output bit stream is captured,
necessary information to generate the control signals to tune the ADC parameters for
best SignalâtoâQuantization Noise Ratio (SQNR) performance is extracted via Leastâ
Mean Squared (LMS) softwareâbased algorithm. Since the two tones are located
outside the band of interest, the proposed global calibration approach can be used
online with no significant effect on the inâband content
A \u3cem\u3eK\u3c/em\u3e-Delta-1-Sigma Modulator for Wideband Analog to Digital Conversion
As CMOS technology shrinks, the transistor speed K-quantizing paths and can achieve significantly higher conversion bandwidths when compared to the traditional deltasigma ADCs. The 8-path KD1S modulator achieves an SNR of 58 dB (or 9.4-bits resolution) when clocked at 100 MHz for a conversion bandwidth of 6.25 MHz and an effective sampling rate equal to 800 MHz. The KD1S modulator has been fabricated in a 500 nm CMOS process and the experimental results are reported. Deficiencies in the first test chip performance are discussed along with their alleviation to achieve theoretical performance
Recommended from our members
Design techniques for low power ADCs
This dissertation presents an incremental analog-to-digital converter (ADC) with digital digital-to-analog converter (DAC) mismatch correction. A theoretical time-domain analysis technique was developed to predict the noise performance of the incremental ADC, and a new optimization technique was proposed to minimize the output noise.
In the calibration mode, the incremental ADC itself is used to measure the mismatches of the internal multi-bit DAC. Three new calibration techniques, equation-solving calibration, inter-DAC mismatch calibration and modified âSarhang-Nejadâ calibration are proposed.
To verify the above techniques, a test chip was designed and fabricated in 0.18 ”m CMOS process. The chip can work in single-sampling or double-sampling mode. Chopping with a fractal sequence is used to eliminate 1/f noise. The calibration circuit was implemented to calibrate the multi-bit DAC mismatches the in single-sampling mode and inter-DAC mismatches in the double-sampling mode.
Finally, two new design techniques for low-power ADCs, the two-step split-junction successive-approximation register (SAR) ADC and the hybrid cascaded âÎŁ ADC, are proposed
Techniques for Wideband All Digital Polar Transmission
abstract: Modern Communication systems are progressively moving towards all-digital transmitters (ADTs) due to their high efficiency and potentially large frequency range. While significant work has been done on individual blocks within the ADT, there are few to no full systems designs at this point in time. The goal of this work is to provide a set of multiple novel block architectures which will allow for greater cohesion between the various ADT blocks. Furthermore, the design of these architectures are expected to focus on the practicalities of system design, such as regulatory compliance, which here to date has largely been neglected by the academic community. Amongst these techniques are a novel upconverted phase modulation, polyphase harmonic cancellation, and process voltage and temperature (PVT) invariant Delta Sigma phase interpolation. It will be shown in this work that the implementation of the aforementioned architectures allows ADTs to be designed with state of the art size, power, and accuracy levels, all while maintaining PVT insensitivity. Due to the significant performance enhancement over previously published works, this work presents the first feasible ADT architecture suitable for widespread commercial deployment.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201
Recommended from our members
Digital enhancement techniques for data converters in scaled CMOS technologies
This thesis presents digital enhancement techniques for data converters in advanced technology nodes. With technology scaling, traditional voltage-domain (VD) analog-to-digital converters (ADCs) face two major challenges: (1) reduction of dynamic range due to supply voltage scaling, and (2) decrease in intrinsic gain of transistors which makes high gain amplifier design tough. To address these challenges, a two-stage ADC architecture is presented which uses time-domain quantization to exploit the advantages of technology scaling. The architecture, consisting of a first stage successive approximation register (SAR) and a second stage ring oscillator, is highly digital and scaling friendly. Two prototypes have been developed to validate the proposed architecture. The 40nm CMOS prototype achieves 75.7 dB dynamic range at an excellent Schreier figure-of-merit of 172.2 dB. The proposed architecture has been extended to a capacitance-to-digital converter and a prototype has been developed in 40nm CMOS. The prototype can sense capacitances with a resolution of 1.3fF and has a Walden figure-of-merit of 60 fJ/step which is more than two times better than the current state-of-the-art. This thesis also presents digital techniques to improve performance of continuous-time(CT), delta-sigma digital-to-analog converters (DACs). Recently, CT delta-sigma DACs have received more attention than their discrete, switched-capacitor counterpart mainly because of low power and/or higher speed of operation. However, a critical disadvantage of CT, delta-sigma DACs is their greatly increased sensitivity to inter-symbol interference (ISI) error. To address this shortcoming of CT DACs, this thesis presents several algorithms that can mitigate ISI error simultaneously with static mismatch error. Further, the proposed algorithms are fully digital in nature and as such, are best poised to take maximum advantage of technology scaling. Thus, the techniques presented in this thesis will be important enabling factors in raising the envelope of performance of CT delta-sigma DACs in advanced technology nodes.Electrical and Computer Engineerin
- âŠ