Low-Power High-Data-Rate Transmitter Design for Biomedical Application

Ph.DDOCTOR OF PHILOSOPH

Automatic calibration of modulated fractional-N frequency synthesizers

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2001.Includes bibliographical references (p. 145-148).This electronic version was submitted by the student author. The certified thesis is available in the Institute Archives and Special Collections.The focus of this research has been the development of a low power, radio frequency transmitter architecture. Specifically, a technique for in service automatic calibration of a modulated phase locked loop (PLL) frequency synthesizer has been developed. Phase/frequency modulation is accomplished by modulating the feedback divide value in a phase locked loop frequency synthesizer. A digital precompensation filter is used to extend the modulation bandwidth by canceling the low-pass transfer function of the PLL. The automatic calibration circuit maintains accurate matching between the digital precompensation filter and the analog PLL transfer function across process and temperature variations. The automatic calibration circuit, which is the main contribution of this thesis, operates while the transmitter is in service. This online calibration eliminates the need for production calibration and periodic down time for calibration cycles.(cont.) In addition the calibration circuitry provides greater accuracy in the modulation than what is possible via offline methods of calibration. The calibration circuit works with M-ary GFSK as well as 2 level GFSK. The automatic calibration circuit has been implemented in two forms to prove its operation. The first version is a circuit board level implementation with a center frequency of around 60 MHz. The second implementation of the system is in a full custom 0.6 ,Lm BiCMOS integrated circuit. The integrated circuit contains the complete synthesizer with automatic calibration and operates in the 1.88 GHz frequency band used by the Digital European Cordless Telephone (DECT) standard. A data rate of 2.5 Mbps using 2 level GFSK and 5.0 Mbps using 4 level GFSK has been achieved with a power consumption of 78 mW.by Daniel R. McMahill.Ph.D

Oscillator Architectures and Enhanced Frequency Synthesizer

A voltage controlled oscillator (VCO), that generates a periodic signal whose frequency is tuned by a voltage, is a key building block in any integrated circuit systems. A sine wave oscillator can be used for a built-in self testing where high linearity is required. A bandpass filter (BPF) based oscillator is a preferred solution, and high quality factor (Q-factor) is needed to improve the linearity. However, a stringent linearity specification may require very high Q-factor, not practical to implement. To address this problem, a frequency harmonic shaping technique is proposed. It utilizes a finite impulse response filter improving the linearity by rejecting certain harmonics. A prototype SC BPF oscillator with an oscillating frequency of 10 MHz is designed and measurement results show that linearity is improved by 20 dB over a conventional oscillator. In radio frequency area, preferred oscillator structures are an LC oscillator and a ring oscillator. An LC oscillator exhibits good phase noise but an expensive cost of an inductor is disadvantageous. A ring oscillator can be built in standard CMOS process, but suffers due to a poor phase noise and is sensitive to supply noise. A RC BPF oscillator is proposed to compromise the above difficulties. A RC BPF oscillator at 2.5 GHz is designed and measured performance is better than ring oscillators when compared using a figure of merit. In particular, the frequency tuning range of the proposed oscillator is superior to the ring oscillator. VCO is normally incorporated with a frequency synthesizer (FS) for an accurate frequency control. In an integer-N FS, reference spur is one of the design concerns in communication systems since it degrades a signal to noise ratio. Reference spurs can be rejected more by either the lower loop bandwidth or the higher loop filter. But the former increases a settling time and the latter decreases phase margin. An adaptive lowpass filtering technique is proposed. The loop filter order is adaptively increased after the loop is locked. A 5.8 GHz integer-N FS is designed and measurement results show that reference spur rejection is improved by 20 dB over a conventional FS without degrading the settling time. A new pulse interleaving technique is proposed and several design modifications are suggested as a future work

Algorithms and Circuits for Analog-Digital Hybrid Multibeam Arrays

Fifth generation (5G) and beyond wireless communication systems will rely heavily on larger antenna arrays combined with beamforming to mitigate the high free-space path-loss that prevails in millimeter-wave (mmW) and above frequencies. Sharp beams that can support wide bandwidths are desired both at the transmitter and the receiver to leverage the glut of bandwidth available at these frequency bands. Further, multiple simultaneous sharp beams are imperative for such systems to exploit mmW/sub-THz wireless channels using multiple reflected paths simultaneously. Therefore, multibeam antenna arrays that can support wider bandwidths are a key enabler for 5G and beyond systems. In general, N-beam systems using N-element antenna arrays will involve circuit complexities of the order of N2. This dissertation investigates new analog, digital and hybrid low complexity multibeam beamforming algorithms and circuits for reducing the associated high size, weight, and power (SWaP) complexities in larger multibeam arrays. The research efforts on the digital beamforming aspect propose the use of a new class of discrete Fourier transform (DFT) approximations for multibeam generation to eliminate the need for digital multipliers in the beamforming circuitry. For this, 8-, 16- and 32-beam multiplierless multibeam algorithms have been proposed for uniform linear array applications. A 2.4 GHz 16-element array receiver setup and a 5.8 GHz 32-element array receiver system which use field programmable gate arrays (FPGAs) as digital backend have been built for real-time experimental verification of the digital multiplierless algorithms. The multiplierless algorithms have been experimentally verified by digitally measuring beams. It has been shown that the measured beams from the multiplierless algorithms are in good agreement with the exact counterpart algorithms. Analog realizations of the proposed approximate DFT transforms have also been investigated leading to low-complex, high bandwidth circuits in CMOS. Further, a novel approach for reducing the circuit complexity of analog true-time delay (TTD) N-beam beamforming networks using N-element arrays has been proposed for wideband squint-free operation. A sparse factorization of the N-beam delay Vandermonde beamforming matrix is used to reduce the total amount of TTD elements that are needed for obtaining N number of beams in a wideband array. The method has been verified using measured responses of CMOS all-pass filters (APFs). The wideband squint-free multibeam algorithm is also used to propose a new low-complexity hybrid beamforming architecture targeting future 5G mmW systems. Apart from that, the dissertation also explores multibeam beamforming architectures for uniform circular arrays (UCAs). An algorithm having N log N circuit complexity for simultaneous generation of N-beams in an N-element UCA is explored and verified

Time-based circuits for communication systems in advanced CMOS technology

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2009.This electronic version was submitted by the student author. The certified thesis is available in the Institute Archives and Special Collections.Cataloged from student submitted PDF version of thesis.Includes bibliographical references (p. 145-151).As device size scales down, there have been challenges to design conventional analog circuits, such as low voltage headroom and the low intrinsic gain of a device. Although ever-decreasing device channel length in CMOS technology has mainly negative effects on analog circuits, it increases device speed and reduces the power consumption of digital circuits. As a result, time-based signal processing has been attracting attention because time-based circuits take advantage of high speed and low power devices to deal with analog information in the time domain. In this thesis, we focus on a ring oscillator as a core time-based circuit for communication systems. Ring oscillators are employed in analog-to-time conversion or time-to-digital conversion. In this work, we present A/D converters and an RF modulator based on ring oscillators in deep sub-micron CMOS processes. We introduce a VCO-based [sigma][delta] A/D converter utilizing a voltage-controlled ring oscillator (ring VCO) as a continuous-time integrator. We propose to replace conventional integrators designed with analog circuits in a [sigma][delta] modulator with a ring VCO and a phase detector, thereby implementing an A/D converter without traditional analog circuits. We also propose a single-slope A/D converter using time-to-digital conversion. By combining a few analog circuits and a ring oscillator based Time-to-Digital Converter (TDC), we achieve highly digital A/D conversion. Finally, we demonstrate a VCO-based RF modulator. The proposed RF modulator generates an RF signal by simply switching transistors. As opposed to an RFDAC approach, the proposed RF modulator is not limited by quantization noise because it employs multiphase PWM signals. A VCO-based OP amp is also introduced as an alternative method of designing an OP amp in deep sub-micron CMOS. The proposed VCO-based OP amp is utilized to generate the multiphase PWM signals in the RF modulator. This thesis also presents the fundamental limitations of a ring oscillator as a timebased circuit. Although the idea of time-based signal processing employing a ring oscillator has its own limitations such as non-linear tuning characteristics and phase noise, the basic idea is worth investigating to solve the serious problems of analog circuits for future CMOS technology.by Min Park.Ph.D

Intersatellite clock synchronization and absolute ranging for gravitational wave detection in space

The Laser Interferometer Space Antenna (LISA) is a European Space Agency (ESA) large-scale space mission, aiming to detect gravitational waves (GWs) in the observation band of 0.1mHz to 1Hz. The constellation is formed by three spacecrafts (SCs), exchanging laser beams with each other. The detector adopts heterodyne interferometry with MHz frequency offsets. GW signals are then encoded in optical beatnote phases, and the phase information has to be extracted by a core device called phasemeter (PM). Unequal and time- varying orbital motions introduce an overwhelming laser noise coupling that impedes the LISA performance levels of 10 ucycle/sqrt(Hz). Thereby, the post-processing technique called time-delay interferometry (TDI) time-shifts phase signals to synthesize virtual equal-arm interferometers. TDI requires absolute-ranging information, as its input, to the accuracy of 1 m rms, which will be provided by monitors like pseudo-random noise ranging (PRNR) and time-delay interferometry ranging (TDIR). An additional challenge is independent clocks on each SC that time-stamp PM data. This, alongside TDI, requires the synchronization of the onboard clocks in post-processing. This thesis reports on the experimental demonstrations of such key components for LISA. This is done by extending the scope of the hexagonal optical testbed at the Albert Einstein Institute (AEI): the "Hexagon". The first part of the thesis focuses on clock synchronization, utilizing the TDIR-like algorithm. With representative technologies both in devices and data analysis, this shows a new benchmark performance of LISA clock synchronization, achieving a 1 ucycle/sqrt(Hz) mark above 60 mHz and a TDIR accuracy of 1.84 m in range. This part also includes the first-ever verification of three noise couplings stemming from TDI and clock synchronization in an optical experiment. The second part of the thesis evolves the Hexagon further with PRNR. It commences with a review of the latest development using a transmission/reception loopback on a single hardware platform. This is followed by the research on the impact of the pseudo-random noise (PRN) modulation on phase tracking. This reveals that the codes, used at best knowledge so far, hinder the carrier phase extraction from achieving the 1 ucycle/sqrt(Hz) mark with realistic data encoded for intersatellite data communication. Some adaptations of PRN codes are proposed, and it is shown that these offer enough suppression of the noise coupling into phase tracking. After phase tracking is confirmed to be compatible with PRN modulations, PRNR itself is inves- tigated. The key novelty of this thesis in terms of PRNR is the study of its absolute-ranging feature, while previous research on this technology focused on stochastic noise properties. This requires the resolution of PRNR ambiguity and the correction of ranging biases. There suggests that the PRNR estimate, alongside some calibrations, can constantly function as absolute ranging with sub-meter accuracy

High Performance Local Oscillator Design for Next Generation Wireless Communication

Local Oscillator (LO) is an essential building block in modern wireless radios. In modern wireless radios, LO often serves as a reference of the carrier signal to modulate or demod- ulate the outgoing or incoming data. The LO signal should be a clean and stable source, such that the frequency or timing information of the carrier reference can be well-defined. However, as radio architecture evolves, the importance of LO path design has become much more important than before. Of late, many radio architecture innovations have exploited sophisticated LO generation schemes to meet the ever-increasing demands of wireless radio performances. The focus of this thesis is to address challenges in the LO path design for next-generation high performance wireless radios. These challenges include (1) Congested spectrum at low radio frequency (RF) below 5GHz (2) Continuing miniaturization of integrated wireless radio, and (3) Fiber-fast (>10Gb/s) mm-wave wireless communication. The thesis begins with a brief introduction of the aforementioned challenges followed by a discussion of the opportunities projected to overcome these challenges. To address the challenge of congested spectrum at frequency below 5GHz, novel ra- dio architectures such as cognitive radio, software-defined radio, and full-duplex radio have drawn significant research interest. Cognitive radio is a radio architecture that opportunisti- cally utilize the unused spectrum in an environment to maximize spectrum usage efficiency. Energy-efficient spectrum sensing is the key to implementing cognitive radio. To enable energy-efficient spectrum sensing, a fast-hopping frequency synthesizer is an essential build- ing block to swiftly sweep the carrier frequency of the radio across the available spectrum. Chapter 2 of this thesis further highlights the challenges and trade-offs of the current LO gen- eration scheme for possible use in sweeping LO-based spectrum analysis. It follows by intro- duction of the proposed fast-hopping LO architecture, its implementation and measurement results of the validated prototype. Chapter 3 proposes an embedded phase-shifting LO-path design for wideband RF self-interference cancellation for full-duplex radio. It demonstrates a synergistic design between the LO path and signal to perform self-interference cancellation. To address the challenge of continuing miniaturization of integrated wireless radio, ring oscillator-based frequency synthesizer is an attractive candidate due to its compactness. Chapter 4 discussed the difficulty associated with implementing a Phase-Locked Loop (PLL) with ultra-small form-factor. It further proposes the concept sub-sampling PLL with time- based loop filter to address these challenges. A 65nm CMOS prototype and its measurement result are presented for validation of the concept. In shifting from RF to mm-wave frequencies, the performance of wireless communication links is boosted by significant bandwidth and data-rate expansion. However, the demand for data-rate improvement is out-pacing the innovation of radio architectures. A >10Gb/s mm-wave wireless communication at 60GHz is required by emerging applications such as virtual-reality (VR) headsets, inter-rack data transmission at data center, and Ultra-High- Definition (UHD) TV home entertainment systems. Channel-bonding is considered to be a promising technique for achieving >10Gb/s wireless communication at 60GHz. Chapter 5 discusses the fundamental radio implementation challenges associated with channel-bonding for 60GHz wireless communication and the pros and cons of prior arts that attempted to address these challenges. It is followed by a discussion of the proposed 60GHz channel- bonding receiver, which utilizes only a single PLL and enables both contiguous and non- contiguous channel-bonding schemes. Finally, Chapter 6 presents the conclusion of this thesis

On-Chip Analog Circuit Design Using Built-In Self-Test and an Integrated Multi-Dimensional Optimization Platform

Nowadays, the rapid development of system-on-chip (SoC) market introduces tremendous complexity into the integrated circuit (IC) design. Meanwhile, the IC fabrication process is scaling down to allow higher density of integration but makes the chips more sensitive to the process-voltage-temperature (PVT) variations. A successful IC product not only imposes great pressure on the IC designers, who have to handle wider variations and enforce more design margins, but also challenges the test procedure, leading to more check points and longer test time. To relax the designers’ burden and reduce the cost of testing, it is valuable to make the IC chips able to test and tune itself to some extent. In this dissertation, a fully integrated in-situ design validation and optimization (VO) hardware for analog circuits is proposed. It implements in-situ built-in self-test (BIST) techniques for analog circuits. Based on the data collected from BIST, the error between the measured and the desired performance of the target circuit is evaluated using a cost function. A digital multi-dimensional optimization engine is implemented to adaptively adjust the analog circuit parameters, seeking the minimum value of the cost function and achieving the desired performance. To verify this concept, study cases of a 2nd/4th active-RC band-pass filter (BPF) and a 2nd order Gm-C BPF, as well as all BIST and optimization blocks, are adopted on-chip. Apart from the VO system, several improved BIST techniques are also proposed in this dissertation. A single-tone sinusoidal waveform generator based on a finite-impulse-response (FIR) architecture, which utilizes an optimization algorithm to enhance its spur free dynamic range (SFDR), is proposed. It achieves an SFDR of 59 to 70 dBc from 150 to 850 MHz after the optimization procedure. A low-distortion current-steering two-tone sinusoidal signal synthesizer based on a mixing-FIR architecture is also proposed. The two-tone synthesizer extends the FIR architecture to two stages and implements an up-conversion mixer to generate the two tones, achieving better than -68 dBc IM3 below 480 MHz LO frequency without calibration. Moreover, an on-chip RF receiver linearity BIST methodology for continuous and discrete-time hybrid baseband chain is proposed. The proposed receiver chain implements a charge-domain FIR filter to notch the two excitation signals but expose the third order intermodulation (IM3) tones. It simplifies the linearity measurement procedure–using a power detector is enough to analyze the receiver’s linearity. Finally, a low cost fully digital built-in analog tester for linear-time-invariant (LTI) analog blocks is proposed. It adopts a time-to-digital converter (TDC) to measure the delays corresponded to a ramp excitation signal and is able to estimate the pole or zero locations of a low-pass LTI system

RF MEMS reference oscillators platform for wireless communications

A complete platform for RF MEMS reference oscillator is built to replace bulky quartz from mobile devices, thus reducing size and cost. The design targets LTE transceivers. A low phase noise 76.8 MHz reference oscillator is designed using material temperature compensated AlN-on-silicon resonator. The thesis proposes a system combining piezoelectric resonator with low loading CMOS cross coupled series resonance oscillator to reach state-of-the-art LTE phase noise specifications. The designed resonator is a two port fundamental width extensional mode resonator. The resonator characterized by high unloaded quality factor in vacuum is designed with low temperature coefficient of frequency (TCF) using as compensation material which enhances the TCF from - 3000 ppm to 105 ppm across temperature ranges of -40˚C to 85˚C. By using a series resonant CMOS oscillator, phase noise of -123 dBc/Hz at 1 kHz, and -162 dBc/Hz at 1MHz offset is achieved. The oscillator’s integrated RMS jitter is 106 fs (10 kHz–20 MHz), consuming 850 μA, with startup time is 250μs, achieving a Figure-of-merit (FOM) of 216 dB. Electronic frequency compensation is presented to further enhance the frequency stability of the oscillator. Initial frequency offset of 8000 ppm and temperature drift errors are combined and further addressed electronically. A simple digital compensation circuitry generates a compensation word as an input to 21 bit MASH 1 -1-1 sigma delta modulator incorporated in RF LTE fractional N-PLL for frequency compensation. Temperature is sensed using low power BJT band-gap front end circuitry with 12 bit temperature to digital converter characterized by a resolution of 0.075˚C. The smart temperature sensor consumes only 4.6 μA. 700 MHz band LTE signal proved to have the stringent phase noise and frequency resolution specifications among all LTE bands. For this band, the achieved jitter value is 1.29 ps and the output frequency stability is 0.5 ppm over temperature ranges from -40˚C to 85˚C. The system is built on 32nm CMOS technology using 1.8V IO device