74 research outputs found

    Design, Analysis and Implementation of DLL clock generator

    Get PDF
    In this paper we present design, analysis and implementation of Delay Locked Loop (DLL) based clock generator circuits. In this work a DLL has been proposed the design uses dynamic phase detector (PD) for phase detection. Voltage controlled delay line (VCDL) of proposed DLL consists of twelve delay elements. Current starved inverters have been used as delay element. In this paper, a proposed duty cycle corrector solves the problem of the sensitivity to half transparent (HT) architecture and the stuck locking error in the DLL simultaneously proposed DLL is designed to work at an input frequency of 250MHz. The design also generates an output of 3GHz using a frequency multiplication block. The design uses 180nm CMOS process technology and consumes 1.88mW of power at 1.8V

    FULLY INTEGRATED HIGH-FREQUENCY CLOCK GENERATION AND SYNCHRONIZATION TECHINIQUES

    Get PDF
    Department of Electrical EngineeringThis thesis presents clock generation and synchronization techniques for RF wireless communication. First, it deals with voltage-controlled oscillators (VCOs) for local oscillators (LO) in transceivers, and secondly delay-locked loops for synchronization. For the high-performance LO, VCO is one of the key blocks. LC VCOs and ring VCOs are commonly-used types. Their characteristics are varied for different frequency bands. In this thesis, two types of VCOs, LC VCO and ring VCO, are presented with specific applications. For the multi-clock generator which could be used for carrier aggregation or frequency hopping, ring-type digitally controlled oscillator (DCO) was designed covering 900-1200 MHz with -165 dB FOM. For the multi-band frequency synthesizer which could be used for 5G communication with backward compatibility, three LC VCOs are designed which frequency range of 25-30 GHz for 5G, 5.2-6.0 GHz for LTE, 2.7-4.2 GHz for 2G-3G communication, respectively. For the clock synchronization in RF communications, a delay-locked loop (DLL) using a digital-to-analog converter (DAC) based band-selecting circuit (BSC) was presented to achieve a wide harmonic-locking-free frequency range. The BSC used the proposed exponential digital-to-analog converter (EDAC) to generate a collection of initial control voltages which follow a sequence of geometric with satisfying the condition for preventing harmonic locking problem. Therefore, the BSC can cover a much wider frequency range which is free from harmonic locking problem compared to initial band selection techniques using conventional, linear DAC (LDAC) that have a set of control voltages of arithmetic sequence. In this thesis, the DLL was implemented in a 65-nm CMOS process, and it had a measured frequency range from 100 to 1500 MHz which range is free from harmonic locking. The measure rms jitter and 1-MHz phase noise at 1000 MHz were 1.99 ps and ?28 dBc/Hz, respectively. The DLL consumes 5.5 mW and its active area was 0.052 mm2.clos

    데이터 전송로 확장성과 루프 선형성을 향상시킨 다중채널 수신기들에 관한 연구

    Get PDF
    학위논문 (박사)-- 서울대학교 대학원 : 전기·컴퓨터공학부, 2013. 2. 정덕균.Two types of serial data communication receivers that adopt a multichannel architecture for a high aggregate I/O bandwidth are presented. Two techniques for collaboration and sharing among channels are proposed to enhance the loop-linearity and channel-expandability of multichannel receivers, respectively. The first proposed receiver employs a collaborative timing scheme recovery which relies on the sharing of all outputs of phase detectors (PDs) among channels to extract common information about the timing and multilevel signaling architecture of PAM-4. The shared timing information is processed by a common global loop filter and is used to update the phase of the voltage-controlled oscillator with better rejection of per-channel noise. In addition to collaborative timing recovery, a simple linearization technique for binary PDs is proposed. The technique realizes a high-rate oversampling PD while the hardware cost is equivalent to that of a conventional 2x-oversampling clock and data recovery. The first receiver exploiting the collaborative timing recovery architecture is designed using 45-nm CMOS technology. A single data lane occupies a 0.195-mm2 area and consumes a relatively low 17.9 mW at 6 Gb/s at 1.0V. Therefore, the power efficiency is 2.98 mW/Gb/s. The simulated jitter is about 0.034 UI RMS given an input jitter value of 0.03 UI RMS, while the relatively constant loop bandwidth with the PD linearization technique is about 7.3-MHz regardless of the data-stream noise. Unlike the first receiver, the second proposed multichannel receiver was designed to reduce the hardware complexity of each lane. The receiver employs shared calibration logic among channels and yet achieves superior channel expandability with slim data lanes. A shared global calibration control, which is used in a forwarded clock receiver based on a multiphase delay-locked loop, accomplishes skew calibration, equalizer adaptation, and the phase lock of all channels during a calibration period, resulting in reduced hardware overhead and less area required by each data lane. The second forwarded clock receiver is designed in 90-nm CMOS technology. It achieves error-free eye openings of more than 0.5 UI across 9− 28 inch Nelco 4000-6 microstrips at 4− 7 Gb/s and more than 0.42 UI at data rates of up to 9 Gb/s. The data lane occupies only 0.152 mm2 and consumes 69.8 mW, while the rest of the receiver occupies 0.297 mm2 and consumes 56 mW at a data rate of 7 Gb/s and a supply voltage of 1.35 V.1. Introduction 1 1.1 Motivations 1.2 Thesis Organization 2. Previous Receivers for Serial-Data Communications 2.1 Classification of the Links 2.2 Clocking architecture of transceivers 2.3 Components of receiver 2.3.1 Channel loss 2.3.2 Equalizer 2.3.3 Clock and data recovery circuit 2.3.3.1. Basic architecture 2.3.3.2. Phase detector 2.3.3.2.1. Linear phase detector 2.3.3.2.2. Binary phase detector 2.3.3.3. Frequency detector 2.3.3.4. Charge pump 2.3.3.5. Voltage controlled oscillator and delay-line 2.3.4 Loop dynamics of PLL 2.3.5 Loop dynamics of DLL 3. The Proposed PLL-Based Receiver with Loop Linearization Technique 3.1 Introduction 3.2 Motivation 3.3 Overview of binary phase detection 3.4 The proposed BBPD linearization technique 3.4.1 Architecture of the proposed PLL-based receiver 3.4.2 Linearization technique of binary phase detection 3.4.3 Rotational pattern of sampling phase offset 3.5 PD gain analysis and optimization 3.6 Loop Dynamics of the 2nd-order CDR 3.7 Verification with the time-accurate behavioral simulation 3.8 Summary 4. The Proposed DLL-Based Receiver with Forwarded-Clock 4.1 Introduction 4.2 Motivation 4.3 Design consideration 4.4 Architecture of the proposed forwarded-clock receiver 4.5 Circuit description 4.5.1 Analog multi-phase DLL 4.5.2 Dual-input interpolating deley cells 4.5.3 Dedicated half-rate data samplers 4.5.4 Cherry-Hooper continuous-time linear equalizer 4.5.5 Equalizer adaptation and phase-lock scheme 4.6 Measurement results 5. Conclusion 6. BibliographyDocto

    Low jitter design techniques for monolithic CMOS phase-locked and delay-locked systems

    Get PDF
    Timing jitter is a major concern in almost every type of communication system. Yet the desire for high levels of integration works against minimization of this error, especially for systems employing a phase-locked loop (PLL) or delay-locked loop (DLL) for timing generation or timing recovery. There has been an increasing demand for fully-monolithic CMOS PLL and DLL designs with good jitter performance. In this thesis, the system level as well as the transistor level low jitter design techniques for integrated PLLs and DLLs have been explored.;On the system level, a rigorous jitter analysis method based on a z-domain model is developed, in which the jitter is treated as a random event. Combined with statistical methods, the rms value of the accumulated jitter can be expressed with a closed form solution that successfully ties the jitter performance with loop parameters. Based on this analysis, a cascaded PLL/DLL structure is proposed which combines the advantage of both loops. The resulting system is able to perform frequency synthesis with the jitter as low as that of a DLL.;As an efficient tool to predict the jitter performance of a PLL or DLL system, a new nonlinear behavioral simulator is developed based on a novel behavioral modeling of the VCO and delay-line. Compared with prior art, this simulator not only simplifies the computation but also enables the noise simulation. Both jitter performance during tracking and lock condition can be predicted. This is also the first reported top-level simulation tool for DLL noise simulation.;On the transistor level, three prototype chips for different applications were implemented and tested. The first two chips are the application of PLL in Gigabit fibre channel transceivers. High speed circuit blocks that have good noise immunity are the major design concern. Testing results show that both designs have met the specifications with low power dissipation. For the third chip, an adaptive on-chip dynamic skew calibration technique is proposed to realize a precise delay multi-phase clock generator, which is a topic that has not been addressed in previous work thus far. Experimental results strongly support the effectiveness of the calibration scheme. At the same time, this design achieves by far the best reported jitter performance

    50-250MHZ ?S DLL for Clock Synchronization

    Get PDF
    Ph.DDOCTOR OF PHILOSOPH

    The Design of Low Power Ultra-Wideband Transceiver

    Get PDF
    Ph.DDOCTOR OF PHILOSOPH

    Techniques for Wideband All Digital Polar Transmission

    Get PDF
    abstract: Modern Communication systems are progressively moving towards all-digital transmitters (ADTs) due to their high efficiency and potentially large frequency range. While significant work has been done on individual blocks within the ADT, there are few to no full systems designs at this point in time. The goal of this work is to provide a set of multiple novel block architectures which will allow for greater cohesion between the various ADT blocks. Furthermore, the design of these architectures are expected to focus on the practicalities of system design, such as regulatory compliance, which here to date has largely been neglected by the academic community. Amongst these techniques are a novel upconverted phase modulation, polyphase harmonic cancellation, and process voltage and temperature (PVT) invariant Delta Sigma phase interpolation. It will be shown in this work that the implementation of the aforementioned architectures allows ADTs to be designed with state of the art size, power, and accuracy levels, all while maintaining PVT insensitivity. Due to the significant performance enhancement over previously published works, this work presents the first feasible ADT architecture suitable for widespread commercial deployment.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201

    Clocking and Skew-Optimization For Source-Synchronous Simultaneous Bidirectional Links

    Get PDF
    There is continuous expansion of computing capabilities in mobile devices which demands higher I/O bandwidth and dense parallel links supporting higher data rates. Highspeed signaling leverages technology advancements to achieve higher data rates but is limited by the bandwidth of the electrical copper channel which have not scaled accordingly. To meet the continuous data-rate demand, Simultaneous Bi-directional (SBD) signaling technique is an attractive alternative relative to uni-directional signaling as it can work at lower clock speeds, exhibits better spectral efficiency and provides higher throughput in pad limited PCBs. For low-power and more robust system, the SBD transceiver should utilize forwarded clock system and per-pin de-skew circuits to correct the phase difference developed between the data and clock. The system can be configured in two roles, master and slave. To save more power, the system should have only one clock generator. The master has its own clock source and shares its clock to the slave through the clock channel, and the slave uses this forwarded clock to deserialize the inbound data and serialize the outbound data. A clock-to-data skew exists which can be corrected with a phase tracking CDR. This thesis presents a low-power implementation of forwarded clocking and clock-to-data skew optimization for a 40 Gbps SBD transceiver. The design is implemented in 28nm CMOS technology and consumes 8.8mW of power for 20 Gbps NRZ data at 0.9 V supply. The area occupied by the clocking 0.018 mm^2 area
    corecore