High speed IC designs for low power short reach optical links

In this thesis, I have briefly introduced the background of my PhD research, current state-of-the-art design, and my PhD research objectives. Then, I demonstrate how to optimize the performance of PAM-4 transmitters based on lumped Silicon Photonic Mach-Zehnder Modulators (MZMs) for short-reach optical links. Firstly, we analyze the trade-off that occurs between extinction ratio and modulation loss when driving an MZM with a voltage swing less than the MZM’s Vπ. This is important when driver circuits are realized in deep submicron CMOS process nodes. Next, a driving scheme based upon a switched capacitor approach is proposed to maximize the achievable bandwidth of the combined lumped MZM and CMOS driver chip. This scheme allows the use of lumped MZM for high speed optical links with reduced RF driver power consumption compared to the conventional approach of driving MZMs (with transmission line based electrodes) with a power amplifier. This is critical for upcoming short-reach link standards such as 400Gb/s 802.3 Ethernet. The driver chip was fabricated using a 65nm CMOS technology and flip-chipped on top of the Silicon Photonic chip (fabricated using IMEC’s ISIPP25G technology) that contains the MZM. Open eyes with 4dB extinction ratio for a 36Gb/s (18Gbaud) PAM- 4 signal are experimentally demonstrated. The electronic driver chip has a core area of only 0.11mm 2 and consumes 236mW from 1.2V and 2.4V supply voltages. This corresponds to an energy efficiency of 6.55pJ/bit including Gray encoder and retiming, or 5.37pJ/bit for the driver circuit only. In the future, system level analysis should be carried out to investigate the critical pattern issue of the PAM4 optical transmitter. The potential solutions toward 1pJ/bit are given (lumped EAM and micro-ring modulator). In addition, the advanced modulation formats (16 QAM, discrete multitone modulation, and FFE) are presented based on the switched capacitor approach

Circuit Techniques for Low-Power and Secure Internet-of-Things Systems

The coming of Internet of Things (IoT) is expected to connect the physical world to the cyber world through ubiquitous sensors, actuators and computers. The nature of these applications demand long battery life and strong data security. To connect billions of things in the world, the hardware platform for IoT systems must be optimized towards low power consumption, high energy efficiency and low cost. With these constraints, the security of IoT systems become a even more difficult problem compared to that of computer systems. A new holistic system design considering both hardware and software implementations is demanded to face these new challenges. In this work, highly robust and low-cost true random number generators (TRNGs) and physically unclonable functions (PUFs) are designed and implemented as security primitives for secret key management in IoT systems. They provide three critical functions for crypto systems including runtime secret key generation, secure key storage and lightweight device authentication. To achieve robustness and simplicity, the concept of frequency collapse in multi-mode oscillator is proposed, which can effectively amplify the desired random variable in CMOS devices (i.e. process variation or noise) and provide a runtime monitor of the output quality. A TRNG with self-tuning loop to achieve robust operation across -40 to 120 degree Celsius and 0.6 to 1V variations, a TRNG that can be fully synthesized with only standard cells and commercial placement and routing tools, and a PUF with runtime filtering to achieve robust authentication, are designed based upon this concept and verified in several CMOS technology nodes. In addition, a 2-transistor sub-threshold amplifier based "weak" PUF is also presented for chip identification and key storage. This PUF achieves state-of-the-art 1.65% native unstable bit, 1.5fJ per bit energy efficiency, and 3.16% flipping bits across -40 to 120 degree Celsius range at the same time, while occupying only 553 feature size square area in 180nm CMOS. Secondly, the potential security threats of hardware Trojan is investigated and a new Trojan attack using analog behavior of digital processors is proposed as the first stealthy and controllable fabrication-time hardware attack. Hardware Trojan is an emerging concern about globalization of semiconductor supply chain, which can result in catastrophic attacks that are extremely difficult to find and protect against. Hardware Trojans proposed in previous works are based on either design-time code injection to hardware description language or fabrication-time modification of processing steps. There have been defenses developed for both types of attacks. A third type of attack that combines the benefits of logical stealthy and controllability in design-time attacks and physical "invisibility" is proposed in this work that crosses the analog and digital domains. The attack eludes activation by a diverse set of benchmarks and evades known defenses. Lastly, in addition to security-related circuits, physical sensors are also studied as fundamental building blocks of IoT systems in this work. Temperature sensing is one of the most desired functions for a wide range of IoT applications. A sub-threshold oscillator based digital temperature sensor utilizing the exponential temperature dependence of sub-threshold current is proposed and implemented. In 180nm CMOS, it achieves 0.22/0.19K inaccuracy and 73mK noise-limited resolution with only 8865 square micrometer additional area and 75nW extra power consumption to an existing IoT system.PHDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttps://deepblue.lib.umich.edu/bitstream/2027.42/138779/1/kaiyuan_1.pd

ULTRA ENERGY-EFFICIENT SUB-/NEAR-THRESHOLD COMPUTING: PLATFORM AND METHODOLOGY

Ph.DDOCTOR OF PHILOSOPH

Circuit Design, Architecture and CAD for RRAM-based FPGAs

Field Programmable Gate Arrays (FPGAs) have been indispensable components of embedded systems and datacenter infrastructures. However, energy efficiency of FPGAs has become a hard barrier preventing their expansion to more application contexts, due to two physical limitations: (1) The massive usage of routing multiplexers causes delay and power overheads as compared to ASICs. To reduce their power consumption, FPGAs have to operate at low supply voltage but sacrifice performance because the transistors drive degrade when working voltage decreases. (2) Using volatile memory technology forces FPGAs to lose configurations when powered off and to be reconfigured at each power on. Resistive Random Access Memories (RRAMs) have strong potentials in overcoming the physical limitations of conventional FPGAs. First of all, RRAMs grant FPGAs non-volatility, enabling FPGAs to be "Normally powered off, Instantly powered on". Second, by combining functionality of memory and pass-gate logic in one unique device, RRAMs can greatly reduce area and delay of routing elements. Third, when RRAMs are embedded into datpaths, the performance of circuits can be independent from their working voltage, beyond the limitations of CMOS circuits. However, researches and development of RRAM-based FPGAs are in their infancy. Most of area and performance predictions were achieved without solid circuit-level simulations and sophisticated Computer Aided Design (CAD) tools, causing the predicted improvements to be less convincing. In this thesis,we present high-performance and low-power RRAM-based FPGAs fromtransistorlevel circuit designs to architecture-level optimizations and CAD tools, using theoretical analysis, industrial electrical simulators and novel CAD tools. We believe that this is the first systematic study in the field, covering: From a circuit design perspective, we propose efficient RRAM-based programming circuits and routing multiplexers through both theoretical analysis and electrical simulations. The proposed 4T(ransitor)1R(RAM) programming structure demonstrates significant improvements in programming current, when compared to most popular 2T1R programming structure. 4T1R-based routingmultiplexer designs are proposed by considering various physical design parasitics, such as intrinsic capacitance of RRAMs and wells doping organization. The proposed 4T1R-based multiplexers outperformbest CMOS implementations significantly in area, delay and power at both nominal and near-Vt regime. From a CAD perspective, we develop a generic FPGA architecture exploration tool, FPGASPICE, modeling a full FPGA fabric with SPICE and Verilog netlists. FPGA-SPICE provides different levels of testbenches and techniques to split large SPICE netlists, in order to obtain better trade-off between simulation time and accuracy. FPGA-SPICE can capture area and power characteristics of SRAM-based and RRAM-based FPGAs more accurately than the currently best analyticalmodels. From an architecture perspective, we propose architecture-level optimizations for RRAMbased FPGAs and quantify their minimumrequirements for RRAM devices. Compared to the best SRAM-based FPGAs, an optimized RRAM-based FPGA architecture brings significant reduction in area, delay and power respectively. In particular, RRAM-based FPGAs operating in the near-Vt regime demonstrate a 5x power improvement without delay overhead as compared to optimized SRAM-based FPGA operating at nominal working voltage

Digital-Based Analog Processing in Nanoscale CMOS ICs for IoT Applications

L'abstract è presente nell'allegato / the abstract is in the attachmen

Digital-based analog processing in nanoscale CMOS ICs for IoT applications

The Internet-of-Things (IoT) concept has been opening up a variety of applications, such as urban and environmental monitoring, smart health, surveillance, and home automation. Most of these IoT applications require more and more power/area efficient Complemen tary Metal–Oxide–Semiconductor (CMOS) systems and faster prototypes (lower time-to market), demanding special modifications in the current IoT design system bottleneck: the analog/RF interfaces. Specially after the 2000s, it is evident that there have been significant improvements in CMOS digital circuits when compared to analog building blocks. Digital circuits have been taking advantage of CMOS technology scaling in terms of speed, power consump tion, and cost, while the techniques running behind the analog signal processing are still lagging. To decrease this historical gap, there has been an increasing trend in finding alternative IC design strategies to implement typical analog functions exploiting Digital in-Concept Design Methodologies (DCDM). This idea of re-thinking analog functions in digital terms has shown that Analog ICs blocks can also avail of the feature-size shrinking and energy efficiency of new technologies. This thesis deals with the development of DCDM, demonstrating its compatibility for Ultra-Low-Voltage (ULV) and Power (ULP) IoT applications. This work proves this state ment through the proposing of new digital-based analog blocks, such as an Operational Transconductance Amplifiers (OTAs) and an ac-coupled Bio-signal Amplifier (BioAmp). As an initial contribution, for the first time, a silicon demonstration of an embryonic Digital-Based OTA (DB-OTA) published in 2013 is exhibited. The fabricated DB-OTA test chip occupies a compact area of 1,426 µm2 , operating at supply voltages (VDD) down to 300 mV, consuming only 590 pW while driving a capacitive load of 80pF. With a Total Harmonic Distortion (THD) lower than 5% for a 100mV input signal swing, its measured small-signal figure of merit (FOMS) and large-signal figure of merit (FOML) are 2,101 V −1 and 1,070, respectively. To the best of this thesis author’s knowledge, this measured power is the lowest reported to date in OTA literature, and its figures of merit are the best in sub-500mV OTAs reported to date. As the second step, mainly due to the robustness limitation of previous DB-OTA, a novel calibration-free digital-based topology is proposed, named here as Digital OTA (DIG OTA). A 180-nm DIGOTA test chip is also developed exhibiting an area below the 1000 µm2 wall, 2.4nW power under 150pF load, and a minimum VDD of 0.25 V. The proposed DIGOTA is more digital-like compared with DB-OTA since no pseudo-resistor is needed. As the last contribution, the previously proposed DIGOTA is then used as a building block to demonstrate the operation principle of power-efficient ULV and ultra-low area (ULA) fully-differential, digital-based Operational Transconductance Amplifier (OTA), suitable for microscale biosensing applications (BioDIGOTA) such as extreme low area Body Dust. Measured results in 180nm CMOS confirm that the proposed BioDIGOTA can work with a supply voltage down to 400 mV, consuming only 95 nW. The BioDIGOTA layout occupies only 0.022 mm2 of total silicon area, lowering the area by 3.22X times compared to the current state of the art while keeping reasonable system performance, such as 7.6 Noise Efficiency Factor (NEF) with 1.25 µVRMS input-referred noise over a 10 Hz bandwidth, 1.8% of THD, 62 dB of the common-mode rejection ratio (CMRR) and 55 dB of power supply rejection ratio (PSRR). After reviewing the current DCDM trend and all proposed silicon demonstrations, the thesis concludes that, despite the current analog design strategies involved during the analog block development

Bascules à impulsion robustes en technologie 28nm FDSOI pour circuits numériques basse consommation à très large gamme de tension d'alimentation

The explosion market of the mobile application and the paradigm of the Internet of Things lead to a huge demand for energy-efficient systems. To overcome the limit of Moore's law due to bulk technology, a new transistor technology has appeared recently in industrial process: the fully-depleted silicon on insulator, or FDSOI.In modern ASIC designs, a large portion of the total power consumption is due to the leaves of the clock tree: the flip-flops. Therefore, the appropriate flip-flop architecture is a major choice to reach the speed and energy constraints of mobile and ultra-low power applications. After a thorough overview of the literature, the explicit pulse-triggered flip-flop topology is pointed out as a very interesting flip-flop architecture for high-speed and low-power systems. However, it is today only used in high-performances circuits mainly because of its poor robustness at ultra-low voltage.In this work, explicit pulse-triggered flip-flops architecture design is developed and studied in order to improve their robustness and their energy-efficiency. A large comparison of resettable and scannable latch architecture is performed in the energy-delay domain by modifying the sizing of the transistors, both at nominal and ultra-low voltage. Then, it is shown that the back biasing technique allowed by the FDSOI technology provides better energy and delay performances than the sizing methodology. As the pulse generator is the main cause of functional failure, we proposed a new architecture which provides both a good robustness at ultra-low voltage and an energy efficiency. A selected topology of explicit pulse-triggered flip-flop was implemented in a 16x32b register file which exhibits better speed, energy consumption and area performances than a version with master-slave flip-flops, mainly thanks to the sharing of the pulse generator over several latches.Avec l'explosion du marché des applications portables et le paradigme de l'Internet des objets, la demande pour les circuits à très haute efficacité énergétique ne cesse de croître. Afin de repousser les limites de la loi de Moore, une nouvelle technologie est apparue très récemment dans les procédés industriels afin de remplacer la technologie en substrat massif ; elle est nommée fully-depleted silicon on insulator ou FDSOI. Dans les circuits numériques synchrones modernes, une grande portion de la consommation totale du circuit provient de l'arbre d'horloge, et en particulier son extrémité : les bascules. Dès lors, l'architecture adéquate de bascules est un choix crucial pour atteindre les contraintes de vitesse et d'énergie des applications basse-consommation. Après un large aperçu de l'état de l'art, les bascules à impulsion explicite sont reconnues les plus prometteuses pour les systèmes demandant une haute performance et une basse consommation. Cependant, cette architecture est pour l'instant fortement utilisée dans les circuits à haute performance et pratiquement absente des circuits à basse tension d'alimentation, principalement à cause de sa faible robustesse face aux variations.Dans ce travail, la conception d'architecture de bascule à impulsion explicite est étudiée dans le but d'améliorer la robustesse et l'efficacité énergétique. Un large panel d'architectures de bascule, avec les fonctions reset et scan, a été comparé dans le domaine énergie-délais, à haute et basse tension d'alimentation, grâce à une méthodologie de dimensionnement des transistors. Il a été montré que la technique dite de « back bias », l'un des principaux avantages de la technologie FDSOI, permettait des meilleures performances en énergie et délais que la méthodologie de dimensionnement. Ensuite, comme le générateur d'impulsion est la principale raison de dysfonctionnement, nous avons proposé une nouvelle architecture qui permet un très bon compromis entre robustesse à faible tension et consommation énergétique. Une topologie de bascule à impulsion explicite a été choisie pour être implémentée dans un banc de registres et, comparé aux bascules maître-esclave, elle présente une plus grande vitesse, une plus faible consommation énergétique et une plus petite surface

完全自動合成可能な低電力・広入力統計的フラッシュ型A/D変換回路

This work presents a fully synthesizable stochastic flash A/D converter (SFADC), which can operate at the supply voltage of 0.6V with power consumption as low as 1.5mW at the clock frequency of 250MHz. By employing the all-digital comparator, the SFADC can be described with Verilog netlist and synthesized according to a standard digital design flow. Cross-coupled dynamic comparator structure saves the overall power due to remarkable control of dynamic power consumption. In addition, the rail-to-rail characteristic of comparator and the proposed linearity enhancement technique based on SFADC are proposed, allowing us to design a wide input-range stochastic flash ADC.北九州市立大

Fabrication, Characterization and Integration of Resistive Random Access Memories

The functionalities and performances of today's computing systems are increasingly dependent on the memory block. This phenomenon, also referred as the Von Neumann bottleneck, is the main motivation for the research on memory technologies. Despite CMOS technology has been improved in the last 50 years by continually increasing the device density, today's mainstream memories, such as SRAM, DRAM and Flash, are facing fundamental limitations to continue this trend. These memory technologies, based on charge storage mechanisms, are suffering from the easy loss of the stored state for devices scaled below 10 nm. This results in a degradation of the performance, reliability and noise margin. The main motivation for the development of emerging non volatile memories is the study of a different mechanism to store the digital state in order to overcome this challenge. Among these emerging technologies, one of the strongest candidate is Resistive Random Access Memory (ReRAM), which relies on the formation or rupture of a conductive filament inside a dielectric layer. This thesis focuses on the fabrication, characterization and integration of ReRAM devices. The main subject is the qualitative and quantitative description of the main factors that influence the resistive memory electrical behavior. Such factors can be related either to the memory fabrication or to the test environment. The first category includes variations in the fabrication process steps, in the device geometry or composition. We discuss the effect of each variation, and we use the obtained database to gather insights on the ReRAM working mechanism and the adopted methodology by using statistical methods. The second category describes how differences in the electrical stimuli sent to the device change the memory performances. We show how these factors can influence the memory resistance states, and we propose an empirical model to describe such changes. We also discuss how it is possible to control the resistance states by modulating the number of input pulses applied to the device. In the second part of this work, we present the integration of the fabricated devices in a CMOS technology environment. We discuss a Verilog-A model used to simulate the device characteristics, and we show two solutions to limit the sneak-path currents for ReRAM crossbars: a dedicated read circuit and the development of selector devices. We describe the selector fabrication, as well as the electrical characterization and the combination with our ReRAMs in a 1S1R configuration. Finally, we show two methods to integrate ReRAM devices in the BEoL of CMOS chips