Fast synchronization 3R burst-mode receivers for passive optical networks

This paper gives a tutorial overview on high speed burst-mode receiver (BM-RX) requirements, specific for time division multiplexing passive optical networks, and design issues of such BM-RXs as well as their advanced design techniques. It focuses on how to design BM-RXs with short burst overhead for fast synchronization. We present design principles and circuit architectures of various types of burst-mode transimpedance amplifiers, burst-mode limiting amplifiers and burst-mode clock and data recovery circuits. The recent development of 10 Gb/s BM-RXs is highlighted also including dual-rate operation for coexistence with deployed PONs and on-chip auto reset generation to eliminate external timing-critical control signals provided by a PON medium access control. Finally sub-system integration and state-of-the-art system performance for 10 Gb/s PONs are reviewed

Experimental comparison of fiber optic parametric, Raman and erbium amplifiers for burst traffic for extended reach PONs

We experimentally compare the performance of a polarization-independent fiber optic parametric amplifier (FOPA), a discrete Raman amplifier and a commercial erbium doped fiber amplifier (EDFA) for burst traffic amplification in extended reach passive optical networks (PON). We demonstrate that EDFA and Raman amplifiers suffer from severe transient effects, causing penalty on receiver sensitivity >5 dB for traffic bursts of 10 Gbps on-off keying signal shorter than 10 µs. On the other hand, we demonstrate that FOPA does not introduce a penalty on receiver sensitivity when amplifying signal bursts as short as 5 µs as compared to a non-burst signal. Therefore, FOPA used as a drop-in replacement for an EDFA or Raman amplifier allows us to improve receiver sensitivity by >3 dB for short signal bursts. We conclude that FOPA allows substantially increased power budget for an extended reach PON transmitting variable duration bursts. In addition, we identify the maximum burst duration tolerated by each examined amplifier

WDM/TDM PON bidirectional networks single-fiber/wavelength RSOA-based ONUs layer 1/2 optimization

This Thesis proposes the design and the optimization of a hybrid WDM/TDM PON at the L1 (PHY) and L2 (MAC) layers, in terms of minimum deployment cost and enhanced performance for Greenfield NGPON. The particular case of RSOA-based ONUs and ODN using a single-fibre/single-wavelength is deeply analysed. In this WDM/TDM PON relevant parameters are optimized. Special attention has been given at the main noise impairment in this type of networks: the Rayleigh Backscattering effect, which cannot be prevented. To understand its behaviour and mitigate its effects, a novel mathematical model for the Rayleigh Backscattering in burst mode transmission is presented for the first time, and it has been used to optimize the WDM/TDM RSOA based PON. Also, a cost-effective, simple design SCM WDM/TDM PON with rSOA-based ONU, was optimized and implemented. This prototype was successfully tested showing high performance, robustness, versatility and reliability. So, the system is able to give coverage up to 1280 users at 2.5 Gb/s / 1.25 Gb/s downstream/upstream, over 20 Km, and being compatible with the GPON ITU-T recommendation. This precedent has enabled the SARDANA network to extend the design, architecture and capabilities of a WDM/TDM PON for a long reach metro-access network (100 km). A proposal for an agile Transmission Convergence sub-layer is presented as another relevant contribution of this work. It is based on the optimization of the standards GPON and XG-PON (for compatibility), but applied to a long reach metro-access TDM/WDM PON rSOA-based network with higher client count. Finally, a proposal of physical implementation for the SARDANA layer 2 and possible configurations for SARDANA internetworking, with the metro network and core transport network, are presented

Towards Higher Speed Next Generation Passive Optical Networks

L'abstract è presente nell'allegato / the abstract is in the attachmen

Power-Proportional Optical Links

The continuous increase in data transfer rate in short-reach links, such as chip-to-chip and between servers within a data-center, demands high-speed links. As power efficiency becomes ever more important in these links, power-efficient optical links need to be designed. Power efficiency in a link can be achieved by enabling power-proportional communication over the serial link. In power-proportional links, the power dissipated by a link is proportional to the amount of data communicated. Normally, data-rate demand is not constant, and the peak data-rate is not required all the time. If a link is not adapted according to the data-rate demand, there will be a fixed power dissipation, and the power efficiency of the link will degrade during the sub-maximal link utilization. Adapting links to real-time data-rate requirements reduces power dissipation. Power proportionality is achieved by scaling the power of the serial link linearly with the link utilization, and techniques such as variable data-rate and burst-mode can be adopted for this purpose. Links whose data rate (and hence power dissipation) can be varied in response to system demands are proposed in this work. Past works have presented rapidly reconfigurable bandwidth in variable data-rate receivers, allowing lower power dissipation for lower data-rate operation. However, maintaining synchronization during reconfiguration was not possible since previous approaches have introduced changes in front-end delay when they are reconfigured. This work presents a technique that allows rapid bandwidth adjustment while maintaining a near-constant delay through the receiver suitable for a power-scalable variable data-rate optical link. Measurements of a fabricated integrated circuit (IC) show nearly constant energy per bit across a 2× variation in data rate while introducing less than 10 % of a unit interval (UI) of delay variation. With continuously increasing data communication in data-centers, parallel optical links with ever-increasing per-lane data rates are being used to meet overall throughput demands. Simultaneously, power efficiency is becoming increasingly important for these links since they do not transmit useful data all the time. The burst-mode solution for vertical-cavity surface-emitting laser (VCSEL)-based point-to-point communication can be used to improve links’ energy efficiency during low link activity. The burst-mode technique for VCSEL-based links has not yet been deployed commercially. Past works have presented burst-mode solutions for single-channel receivers, allowing lower power dissipation during low link activity and solutions for fast activation of the receivers. However, this work presents a novel technique that allows rapid activation of a front-end and fast locking of a clock-and-data-recovery (CDR) for a multi-channel parallel link, utilizing opportunities arising from the parallel nature of many VCSEL-based links. The idea has been demonstrated through electrical and optical measurements of a fabricated IC at 10 Gbps, which show fast data detection and activation of the circuitry within 49 UIs while allowing the front-end to achieve better energy efficiency during low link activity. Simulation results are also presented in support of the proposed technique which allows the CDR to lock within 26 UIs from when it is powered on

Performance Analysis of Optical Communication Systems using OFDM by Employing QPSK Modulation

The high data rate along with good Quality of Service (QoS) requirements of Next Generation Network (NGN) can be fulfilled by using the optical fiber communication networks. At high data rate, dispersion will be the limiting factor which needs to be suitably compensated. Many efforts have been drawn to the development of dispersion compensating devices / techniques to recover or prevent the broadening signal pulse. The Orthogonal Frequency Division Multiplexing (OFDM) is very attractive because of its capacity to handle the dispersion causing pulse broadening at the receiver without changing the internal architecture of the system. Thus Integration of Optical Communication Systems with OFDM system appears to be the most suitable technology for the NGN. The work presented here consist of the design, simulation and performance evaluation for the dispersion compensation in optical fiber communication systems using OFDM for high data rate transmission by utilizing the capacity of the optical fiber channel efficiently. The system performance has been analyzed and compared it with the single carrier optical communication systems. Various simulation results show that systems using OFDM can give dynamically tunable compensation of the dispersion by changing the various parameters of the OFDM systems. The work presented here reveals that the use of OFDM can be used to construct cost effective, high data capacity optical communication systems with extended transmission distance by employing dispersion compensation. These systems have the ability of supporting data rate up to 40 Gbps per optical channel and are appropriate for implementation as upgraded long haul high data rate optical Communication systems. DOI: 10.17762/ijritcc2321-8169.15014

Performance and policy dimensions in internet routing

The Internet Routing Project, referred to in this report as the 'Highball Project', has been investigating architectures suitable for networks spanning large geographic areas and capable of very high data rates. The Highball network architecture is based on a high speed crossbar switch and an adaptive, distributed, TDMA scheduling algorithm. The scheduling algorithm controls the instantaneous configuration and swell time of the switch, one of which is attached to each node. In order to send a single burst or a multi-burst packet, a reservation request is sent to all nodes. The scheduling algorithm then configures the switches immediately prior to the arrival of each burst, so it can be relayed immediately without requiring local storage. Reservations and housekeeping information are sent using a special broadcast-spanning-tree schedule. Progress to date in the Highball Project includes the design and testing of a suite of scheduling algorithms, construction of software reservation/scheduling simulators, and construction of a strawman hardware and software implementation. A prototype switch controller and timestamp generator have been completed and are in test. Detailed documentation on the algorithms, protocols and experiments conducted are given in various reports and papers published. Abstracts of this literature are included in the bibliography at the end of this report, which serves as an extended executive summary

A Fully Bidirectional Optical Network With Latency Monitoring Capability for the Distribution of Timing-Trigger and Control Signals in High-Energy Physics Experiments

The present paper discusses recent advances on a Passive Optical Network inspired Timing-Trigger and Control scheme for the future upgrade of the TTC system installed in the LHC experiments' and more specifically the currently known as TTCex to TTCrx link. The timing PON is implemented with commercially available FPGAs and 1-Gigabit Ethernet PON transceivers and provides a fixed latency gigabit downlink that can carry level-1 trigger accept decisions and commands as well as an upstream link for feedback from the front-end electronics

Canadian Hydrogen Intensity Mapping Experiment (CHIME) Pathfinder

A pathfinder version of CHIME (the Canadian Hydrogen Intensity Mapping Experiment) is currently being commissioned at the Dominion Radio Astrophysical Observatory (DRAO) in Penticton, BC. The instrument is a hybrid cylindrical interferometer designed to measure the large scale neutral hydrogen power spectrum across the redshift range 0.8 to 2.5. The power spectrum will be used to measure the baryon acoustic oscillation (BAO) scale across this poorly probed redshift range where dark energy becomes a significant contributor to the evolution of the Universe. The instrument revives the cylinder design in radio astronomy with a wide field survey as a primary goal. Modern low-noise amplifiers and digital processing remove the necessity for the analog beamforming that characterized previous designs. The Pathfinder consists of two cylinders 37\,m long by 20\,m wide oriented north-south for a total collecting area of 1,500 square meters. The cylinders are stationary with no moving parts, and form a transit instrument with an instantaneous field of view of $\sim$100\,degrees by 1-2\,degrees. Each CHIME Pathfinder cylinder has a feedline with 64 dual polarization feeds placed every $\sim$30\,cm which Nyquist sample the north-south sky over much of the frequency band. The signals from each dual-polarization feed are independently amplified, filtered to 400-800\,MHz, and directly sampled at 800\,MSps using 8 bits. The correlator is an FX design, where the Fourier transform channelization is performed in FPGAs, which are interfaced to a set of GPUs that compute the correlation matrix. The CHIME Pathfinder is a 1/10th scale prototype version of CHIME and is designed to detect the BAO feature and constrain the distance-redshift relation.Comment: 20 pages, 12 figures. submitted to Proc. SPIE, Astronomical Telescopes + Instrumentation (2014