A note on the existence of standard splittings for conformally stationary spacetimes

Let $(M,g)$ be a spacetime which admits a complete timelike conformal Killing vector field $K$. We prove that $(M,g)$ splits globally as a standard conformastationary spacetime with respect to $K$ if and only if $(M,g)$ is distinguishing (and, thus causally continuous). Causal but non-distinguishing spacetimes with complete stationary vector fields are also exhibited. For the proof, the recently solved "folk problems" on smoothability of time functions (moreover, the existence of a {\em temporal} function) are used.Comment: Metadata updated, 6 page

Experimental comparison between R152a and R134a working in a refrigeration facility equipped with a hermetic compressor

[EN] The EU Regulation 517/2014 has recently been approved in a further attempt to curb the effects of GlobalWarming. As a consequence, the refrigeration sector is moving towards refrigerants with a low GlobalWarming Potential (GWP100) in accordance with the limit fixed by these regulations (150). In this regard, the old refrigerant R152a attracts renewed interest due to its low GWP (138) and its similarity to R134a. The present work shows the results of using R152a in a vapour compression plant equipped with a hermetic compressor and an IHX designed for R134a. The refrigerant was replaced by a conventional drop-in process in order to carry out an energy comparison. The results have revealed an improvement in the COP with R152a up to 13% despite a reduction in the cooling capacity of about 10%. During the test campaign, R134a hermetic compressors have been shown to be capable of operating with R152a.The authors acknowledge Jaume I University of Spain, who financed partially the present study through the research project P1.B2013-10.Cabello, R.; Sanchez, D.; Llopis Doménech, R.; Armendáriz Araúzo, LM.; Torrella Alcaraz, E. (2015). Experimental comparison between R152a and R134a working in a refrigeration facility equipped with a hermetic compressor. International Journal of Refrigeration. 60:92-105. https://doi.org/10.1016/j.ijrefrig.2015.06.021S921056

An Economical and Environmental Alternative to Traditional Can Manufacturing Using a New Pre-Laminated Steel

[EN] Metal containers are the most commonly used packaging worldwide in both the food and beverage industry. Some manufacturing processes in the canning industry include multi-step transformations that take large aluminum or steel coils and make them into two or three-piece cans. During this process, the containers are sprayed to obtain a better surface for the contents; however, this spray produces volatile organic compounds (VOC). This paper presents a new and environmentally friendly can manufacturing method, which uses a novel pre-laminated two-layer polymer steel. As experimentally proven, this innovative polymer-coated steel successfully withstands every manufacturing requirement. The specimens were tested in an ironing simulator, measuring roughness and friction coefficients. The development of an upper bound ironing model, along with a supporting neural network, allows an insight into the design of new materials for can manufacturing.Sellés Cantó, MÁ.; Schmid, SR.; Sanchez-Caballero, S.; Ramezani, M.; Pérez Bernabeu, E. (2020). An Economical and Environmental Alternative to Traditional Can Manufacturing Using a New Pre-Laminated Steel. Materials Proceedings. 2(21):1-10. https://doi.org/10.3390/CIWC2020-06841S11022

Flexible Work Arrangements and Employee Work Attitudes: A Case-Based Inquiry of a Small Non-Profit Response to Crisis

We conducted an exploratory case-based study to examine the impact of adopting flexible work arrangements strategies in response to the Covid-19 pandemic on employee work attitudes for a small, regional non-profit. Our findings indicated the importance of managerial support and organizational commitment to moderate the relationship between flexible work arrangements and job satisfaction. We also explored the influence of technology efficacy and work-life balance on the model. Our paper provides support for the prior empirical and theoretical assumptions that flexible work arrangements can have a positive impact on employee work attitudes and may be an effective managerial tool in response to a crisis

Optimization of laser-firing processes for silicon-heterojunction solar-cell back contacts

One of the key steps to achieve high efficiencies in amorphous/crystalline silicon photovoltaic structures is to design low-ohmic-resistance backcontacts with good passivation in the rear part of the cell. A well known approach to achieve this goal is to use laser-fired contact (LFC) processes in which a metal layer is fired through the dielectric to define good contacts with the semiconductor. However, and despite the fact that this approach has demonstrated to be extremely successful, there is still enough room for process improvement with an appropriate optimization. In this paper, a study focused on the optimal adjustment of the irradiation parameters to produce laser-fired contacts in a-Si:H/c-Si heterojunctionsolarcells is presented. We used samples consisting of crystalline-silicon (c-Si) wafers together with a passivation layer of intrinsic hydrogenated amorphous silicon (a-Si:H(i)) deposited by plasma-enhanced chemical deposition (PECVD). Then, an aluminum layer was evaporated on both sides, the thickness of this layer varied from 0.2 to 1 μm in order to identify the optimal amount of Al required to create an appropriate contact. A q-switched Nd:YVO4laser source, λ = 532 nm, was used to locally fire the aluminum through the thin a-Si:H(i)-layers to form the LFC. The effects of laser fluences were analyzed using a comprehensive morphological and electrical characterization

Optimization of laser-firing processes for silicon-heterojunction solar-cell back contacts

One of the key steps to achieve high efficiencies in amorphous/crystalline silicon photovoltaic structures is to design low-ohmic-resistance backcontacts with good passivation in the rear part of the cell. A well known approach to achieve this goal is to use laser-fired contact (LFC) processes in which a metal layer is fired through the dielectric to define good contacts with the semiconductor. However, and despite the fact that this approach has demonstrated to be extremely successful, there is still enough room for process improvement with an appropriate optimization. In this paper, a study focused on the optimal adjustment of the irradiation parameters to produce laser-fired contacts in a-Si:H/c-Si heterojunctionsolarcells is presented. We used samples consisting of crystalline-silicon (c-Si) wafers together with a passivation layer of intrinsic hydrogenated amorphous silicon (a-Si:H(i)) deposited by plasma-enhanced chemical deposition (PECVD). Then, an aluminum layer was evaporated on both sides, the thickness of this layer varied from 0.2 to 1 μm in order to identify the optimal amount of Al required to create an appropriate contact. A q-switched Nd:YVO4laser source, λ = 532 nm, was used to locally fire the aluminum through the thin a-Si:H(i)-layers to form the LFC. The effects of laser fluences were analyzed using a comprehensive morphological and electrical characterization

OSIRIS Software: The Mask Designer Tool

OSIRIS is a Day One instrument that will be available at the 10m GTC telescope which is being built at La Palma observatory in the Canary Islands. This optical instrument is designed to obtain wide-field narrow-band images using tunable filters and to do low-resolution spectroscopy in both long-slit and multislit modes. For the multislit spectroscopy mode, we have developed a software to assist the observers to design focal plane masks. In this paper we describe the characteristics of this Mask Designer tool. We discuss the main design concepts, the functionality and particular features of the software.Comment: 6 figures; accepted for publication in Experimental Astronom

Influence of laser wavelength on Laser-Fired contacts for crystalline silicon solar cells

In the Laser-Fired Contact (LFC) process, a laser beam fires a metallic layer through a dielectric passivating layer into the silicon wafer to form an electrical contact with the silicon bulk [1]. This laser technique is an interesting alternative for the fabrication of both laboratory and industrial scale high efficiency passivated emitter and rear cell (PERC). One of the principal characteristics of this promising technique is the capability to reduce the recombination losses at the rear surface in crystalline silicon solar cells. Therefore, it is crucial to optimize LFC because this process is one of the most promising concepts to produce rear side point contacts at process speeds compatible with the final industrial application. In that sense, this work investigates the optimization of LFC processing to improve the back contact in silicon solar cells using fully commercial solid state lasers with pulse width in the ns range, thus studying the influence of the wavelength using the three first harmonics (corresponding to wavelengths of 1064 nm, 532 nm and 355 nm). Previous studies of our group focused their attention in other processing parameters as laser fluence, number of pulses, passivating material [2, 3] thickness of the rear metallic contact [4], etc. In addition, the present work completes the parametric optimization by assessing the influence of the laser wavelength on the contact property. In particular we report results on the morphology and electrical behaviour of samples specifically designed to assess the quality of the process. In order to study the influence of the laser wavelength on the contact feature we used as figure of merit the specific contact resistance. In all processes the best results have been obtained using green (532 nm) and UV (355 nm), with excellent values for this magnitude far below 1 mΩcm2