CAMIEM: Compact Additively Manufactured Innovative Electric Motor

New manufacturing methods are needed to obtain innovative electric motor designs that have much higher power densities and/or efficiencies compared to the current state-of-the-art. Additive manufacturing offers the potential to radically change motor designs so that they have compact designs, multi-material components, innovative cooling, and optimally designed and manufactured components. New component designs enabled by additive manufacturing technologies have been designed and were fabricated to include the housing, rotors, stator cooling ring, a direct printed stator, and a wire embedded stator. The new components were integrated into the motor and tested evaluate the performance gains in comparison to the baseline electric motor configuration. Partners on the sub-project include NASA GRC, NASA LaRC, NASA AFRC, LaunchPoint Technologies, and the University of Texas El Paso

Development and Characterization of the Bonding and Integration Technologies Needed for Fabricating Silicon Carbide Based Injector Components

Advanced ceramic bonding and integration technologies play a critical role in the fabrication and application of silicon carbide based components for a number of aerospace and ground based applications. One such application is a lean direct injector for a turbine engine to achieve low NOx emissions. Ceramic to ceramic diffusion bonding and ceramic to metal brazing technologies are being developed for this injector application. For the diffusion bonding technology, titanium interlayers (coatings and foils) were used to aid in the joining of silicon carbide (SiC) substrates. The influence of such variables as surface finish, interlayer thickness, and processing time were investigated. Electron microprobe analysis was used to identify the reaction formed phases. In the diffusion bonds, an intermediate phase, Ti5Si3Cx, formed that is thermally incompatible in its thermal expansion and caused thermal stresses and cracking during the processing cool-down. Thinner interlayers of pure titanium and/or longer processing times resulted in an optimized microstructure. Tensile tests on the joined materials resulted in strengths of 13-28 MPa depending on the SiC substrate material. Nondestructive evaluation using ultrasonic immersion showed well formed bonds. For the joining technology of brazing Kovar fuel tubes to silicon carbide, preliminary development of the joining approach has begun. Various technical issues and requirements for the injector application are addressed

NASA Subsonic Rotary Wing Project - Structures and Materials Discipline

The Structures & Materials Discipline within the NASA Subsonic Rotary Wing Project is focused on developing rotorcraft technologies. The technologies being developed are within the task areas of: 5.1.1 Life Prediction Methods for Engine Structures & Components 5.1.2 Erosion Resistant Coatings for Improved Turbine Blade Life 5.2.1 Crashworthiness 5.2.2 Methods for Prediction of Fatigue Damage & Self Healing 5.3.1 Propulsion High Temperature Materials 5.3.2 Lightweight Structures and Noise Integration The presentation will discuss rotorcraft specific technical challenges and needs as well as details of the work being conducted in the six task areas

Enabling Additive Manufacturing Technologies for Advanced Aero Propulsion Materials & Components

Additive manufacturing (AM) technologies are enabling for advanced high performance, propulsion component designs in electric motors1-2 and turbine engine systems in future electrified aircraft. AM offers significant benefits over conventional manufacturing to fabricate components that are more compact, lighter weight, geometrically complex, innovatively cooled, integrated, multi-material, and multifunctional. For turbine engine applications, silicon carbide (SiC) based composites are being pursued using binder jetting and laminated object manufacturing (LOM) for components such as shrouds, vanes, and recuperators. For electric motor applications, additive processes are being applied toward optimized component designs to include the housing, rotor, and stators with 3-D printing and wire imbedded coils and with direct printed 3-phase coils. The electrical conductivity of silver conductor coils optimized by evaluating alternate sintering methods and additions of graphene and carbon nanostructures will be presented. Potential benefits of new electric motor components in improving temperature capability, efficiency, and power density for reductions in energy consumption and emissions will be discussed

Ceramic Matrix Composites for Rotorcraft Engines

Ceramic matrix composite (CMC) components are being developed for turbine engine applications. Compared to metallic components, the CMC components offer benefits of higher temperature capability and less cooling requirements which correlates to improved efficiency and reduced emissions. This presentation discusses a technology develop effort for overcoming challenges in fabricating a CMC vane for the high pressure turbine. The areas of technology development include small component fabrication, ceramic joining and integration, material and component testing and characterization, and design and analysis of concept components

Highly Variable Cycle Nozzle Concept: Validation of Flow and Noise Predictions

Results from experimental and numerical studies of highly Variable Cycle (HVC) exhaust model were presented. The model was designed and fabricated under a Supersonics NRA awarded to Rolls-Royce. The model had a lobed mixer for the core stream nozzle, and elliptic fan stream nozzle, and an ejector. Experiments included far-field acoustic array, phased array, and Particle Image Velocimetry (PIV) measurements. Numerical studies included flow simulations using the WIND-US code and far-field acoustic solutions using an acoustic analogy developed by Goldstein (2003) and Leib and Goldstein (2011). Far-field acoustic measurements showed increased noise levels over the round baseline nozzle when using non-static forward flight conditions. Phased array measurements showed noise sources near the ejector doors when tones were produced for small ejector door positions. Ejector door separation identified in the experiments was reproduced in the numerical flow simulations. Acoustic solutions were unable to match levels measured in the peak jet noise direction indicating additional development work is needed to predict noise from highly three-dimensional flows

Development and High Pressure Burner Rig Demonstration of SiC/SiC Ceramic Matrix Composite Combustor Liners with Environmental Barrier Coatings

No abstract availabl

TEM Observation of the Ti Interlayer Between SiC Substrates During Diffusion Bonding

Diffusion bonding was carried out to join SiC to SiC substrates using titanium interlayers. In this study, 10 m and 20 m thick physical vapor deposited (PVD) Ti surface coatings, and 10 and 20 m thick Ti foils were used. Diffusion bonding was performed at 1250 C for PVD Ti coatings and 1200 C for Ti foil. This study investigates the microstructures of the phases formed during diffusion bonding through TEM and selected-area diffraction analysis of a sample prepared with an FIB, which allows samples to be taken from the reacted area. In all samples, Ti3SiC2, Ti5Si3Cx and TiSi2 phases were identified. In addition, TiC and unknown phases also appeared in the samples in which Ti foils were used as interlayers. Furthermore, Ti3SiC2 phases show high concentration and Ti5Si3Cx formed less when samples were processed at a higher temperature and thinner interlayer samples were used. It appears that the formation of microcracks is caused by the presence of intermediate phase Ti5Si3Cx, which has anisotropic thermal expansion, and by the presence of an unidentified Ti-Si-C ternary phase with relatively low Si content

A Fully Non-Metallic Gas Turbine Engine Enabled by Additive Manufacturing

In a NASA Aeronautics Research Institute (NARI) sponsored program entitled "A Fully Non-Metallic Gas Turbine Engine Enabled by Additive Manufacturing", evaluation of emerging materials and additive manufacturing technologies was carried out. These technologies may enable fully non-metallic gas turbine engines in the future. This paper highlights the results of engine system trade studies which were carried out to estimate reduction in engine emissions and fuel burn enabled due to advanced materials and manufacturing processes. A number of key engine components were identified in which advanced materials and additive manufacturing processes would provide the most significant benefits to engine operation. In addition, feasibility of using additive manufacturing technologies to fabricate gas turbine engine components from polymer and ceramic matrix composite were demonstrated. A wide variety of prototype components (inlet guide vanes (IGV), acoustic liners, engine access door) were additively manufactured using high temperature polymer materials. Ceramic matrix composite components included first stage nozzle segments and high pressure turbine nozzle segments for a cooled doublet vane. In addition, IGVs and acoustic liners were tested in simulated engine conditions in test rigs. The test results are reported and discussed in detail

Oxidation of Carbon Fibers in a Cracked Ceramic Matrix Composite Modeled as a Function of Temperature

The oxidation model simulates the oxidation of the reinforcing carbon fibers within a ceramic matrix composite material containing as-fabricated microcracks. The physics-based oxidation model uses theoretically and experimentally determined variables as input for the model. The model simulates the ingress of oxygen through microcracks into a two-dimensional plane within the composite material. Model input includes temperature, oxygen concentration, the reaction rate constant, the diffusion coefficient, and the crack opening width as a function of the mechanical and thermal loads. The model is run in an iterative process for a two-dimensional grid system in which oxygen diffuses through the porous and cracked regions of the material and reacts with carbon in short time steps. The model allows the local oxygen concentrations and carbon volumes from the edge to the interior of the composite to be determined over time. Oxidation damage predicted by the model was compared with that observed from microstructural analysis of experimentally tested composite material to validate the model for two temperatures of interest. When the model is run for low-temperature conditions, the kinetics are reaction controlled. Carbon and oxygen reactions occur relatively slowly. Therefore, oxygen can bypass the carbon near the outer edge and diffuse into the interior so that it saturates the entire composite at relatively high concentrations. The kinetics are limited by the reaction rate between carbon and oxygen. This results in an interior that has high local concentrations of oxygen and a similar amount of consumed carbon throughout the cross section. When the model is run for high-temperature conditions, the kinetics are diffusion controlled. Carbon and oxygen reactions occur very quickly. The carbon consumes oxygen as soon as it is supplied. The kinetics are limited by the relatively slow rate at which oxygen is supplied in comparison to the relatively fast rate at which carbon and oxygen reactions occur. This results in a sharp gradient in oxygen concentration from the edge where it is supplied to the nearest source of carbon, which is where the oxygen is quickly consumed. A moving reaction front is seen in which the outlaying carbon is consumed before the next inner layer of carbon begins to react