The establishment of minimum luminous range for existing lighthouses in the age of global navigation satellite system by limiting the luminous range within geographical range

Long range marine aids to navigation is not required by current marine navigational practice, therefore luminous range of lighthouses should be reduced. The objective of this study is to determine a minimum luminous range for major lighthouses. The minimum luminous ranges is determined by conducting two steps, namely by modifying the existing geographical range formula and determine a strong linear correlation between light intensity and luminous range with the lowest gradient as possible in a linear graph. The application of minimum luminous range would eliminate the loom of light beyond the lighthouse's geographical range, which is not necessary for current navigational practice. This method is applied to seven major lighthouses in Peninsular Malaysia, which resulted minimum luminous range that ranging from 12.2 nm to 14 nm. The existing luminous ranges of these lighthouses are ranging from 18 nm to 25 nm. These new minimum luminous ranges are sufficient for mariners who primarily rely on GNSS, reduce service provider operational cost and may sustain lighthouses operation in the future

Carbonization cbn550 effect on tensile properties of composite for marine structure application

The composites have gained commercial success, where strength, stiffness, durability and light weight are required as well as retardant capacity. Improvement has been made such new series of resin such as vinyl ester and epoxy type[1, 2]. However 95% of pleasure vessels and boats under 60 feet today are still made with polyester resin. The main consideration for most composite builders is cost, with performance and more importantly value for money often being a secondary consideration. Therefore, this study investigate the tensile - mechanical effects of mixing carbon black CBN550 with wax and non-wax type resin and manufactured according to fiber orientation of [0°] and [90°]. The 10% CBN550 exhibit highest reading for stress under [90°] fiber orientation and the lowest reading when arranged at [0°] fiber orientation. The preliminary study on CBN550 flammability has indicated the suitability for this study to pursue in. The structural composites samples of 1000 mm by 1000 mm prepared which consist of 10 of composite mats layer in combination of CSM 450 g/m2 and Woven Roving 600 g/m2. The carbon black (CB) volume fraction range from/with 0% to 20% volume fractions. Optical observation revealed the most suitable fraction of CBN550 in wax polyester resin is at 10% and non-wax polyester resin is also at 10%. The fire resistance behaviour of this CBN550 - CSM 450 g/m2 - Woven Roving 600 g/m2 composite (polyester wax) and polyester non wax was investigated previously as per[3]. This results are in line with the finding of the maximum load where the highest reading was recorded by the 10%CBN550 specimen. This study showed that the introduction of carbon black into the resin mixture helps reinforce the matrix materials. The results suggested that CBN550 mixture should attend to next level of experiment investigation such as oxygen content, TG value, microstructure and other mechanical destructive test. The CBN550 could be a suitable candidate for fire retardance application in marine composite structure

The effect of N550 carbon black in polyester resin for fire-retardant application in marine composite

This paper presents the experimental investigation on the influence of N550 carbon black (CBN550) series in polyester resin (wax and non -wax type). The CBN550 was added into polyester resin at different weight percentages with a curing agent. The investigation is mainlyto study the effect on fire retardance application in marine composite structure. The fire-resistant structural composites samples of 1000 mm by 1000 mm prepared which consist of 10 of composite mats layer in combination of CSM 450 g/m2 and Woven Roving 600 g/m2. The carbon black (CB) volume fraction range from/with 0% to 20% volume fractions. Optical observation revealed the most suitable fraction of CBN550 in wax polyester resin is at 10% and non-wax polyester resin is also at 10%. The fire resistance behavior of this CBN550 - CSM 450 g/m2 - Woven Roving 600 g/m2 composite (polyester wax) and polyester non wax was investigated by Fire Test Procedure Code-Resolution A.653 [1]. Though smaller filler size escalates the rheological behavior and values outstandingly at initial reading compare to large particles but it slow down the curing processdue to its small particle size, large surface area and high dispersion rate. Experimental data showed the retardance level has been increased up to 56.66% in non-wax type polyester resin (10%/CBN550) and 30.14% in wax polyester resin (10%/CBN550). The improvement in fire resistance points are due to the presence of CBN550 which acts as a positive additive in both polyester resin wax and non-wax. Filling CBN550 in polyester resin also reduces the cost of theend products.The preliminary results suggested that CBN550should attend to next level of experiment investigation such as oxygen content, TG value, microstructure as well as mechanical destructive test. The CBN550 could be a suitable candidate for fire retardance application in marine composite structure.In conclusion, crystallinity of polyester resin increases with additional of CB particles

Bima “Biogas Mandiri” Hasil Pengolahan Limbah Cair Tahu Dengan Digester Anaerob Tipe Fixe Dome Untuk Terciptanya Energi Pedesaan, Adiwerna, Tegal

Berdasarkan segala aspek kehidupan yang dituntut untuk berkembang guna memenuhi standar kualitas hidup manusia yang lebih tinggi, yang disertai adanya faktor perusak lingkungan berupa limbah.Hal demikian mendorong kami untuk berinovasi menciptakan teknologi tepat guna yang membantu mengatasi perihal tersebut.Minimnya kesadaran serta pengetahuan akan pengolahan limbah produksi tahu, mengakibatkan pencemaran lingkungan di area sekitar tempat pembuangan limbah tahu berupa bau yang tidak sedap serta lingkungan yang kotor akibat buangan limbah. Upaya masyarakat dukuh Pesalakan,kecamatan Adiwerna , Tegal, dengan membuat IPAL pengolah limbah tahu , dirasa kurang optimal dalam mengakomodasi keseluruhan produksi limbah tahu dari masyarakat dilingkungannya.Dengan demikian untuk mengatasi perihal tersebut maka pengolahan limbah yang tidak tertampung IPAL dapat diatasi dengan teknologi berupa reaktor biodigester.Limbah yang tidak tersalurkan tentunya dapat diolah dan dijadikan gas yang bermanfaat untuk kebutuhan sehari-hari warga dan mampu menjadi energi terbarukan.Dengan pengadaan biodigester, di proyeksikan mampu meningkatkan kualitas hidup masyarakat dukuh Pesalakan, dan menjadikannnya sebagai desa percontohan sebagai desa mandiri energi.Kata kunci : “Inovasi”, ”teknologi tepat guna”, “limbah tahu”, “biodigester”,  “energi terbarukan

Fuel saving analysis and stability assessments of malaysian offshore fishing vessels fitted with dual fuel diesel and compressed natural gas

Malaysia fishing industries are heavily dependent on the fossil fuels to satisfy its energy demand. Fuel cost of fishing vessels normally accounts for more than 50% of the annual operating expenses. With the increasing of global fuel prices, the future of this industry has exposed fishermen to uncertain future. Nowadays, clean burning alternative fuel such natural gas has become a great interest for fuel saving. A duel fuel diesel engine is a diesel engine that has been fitted to use compressed natural gas (CNG). Dual fuel engines provide numerous potential advantages such as cost saving, fuel flexibility, lower emissions, better efficiency and easy conversion of existing diesel engines without major modifications. This paper describes a study to reduce fuel consumption by introducing a dual fuel diesel and CNG for Malaysian offshore fishing vessel. An analysis of fuel consumption reduction is presented, together with stability assessments. The results reveals that dual fuel diesel can provide noticeable lower fuel consumption compared to existing diesel engines and stability assessment signify that the conversion to dual fuel engine has no adverse effects to vessel stability

CONCEPTUAL DESIGN OF AUTONOMOUS CART FOLLOWER FOR WHEELCHAIR USER

This paper focuses on kinematics of the cart follower and the system identification of propulsion system by using brushed DC motor. The cart follower uses Ackermann configuration as the steering system. The modeling of kinematics equation takes into account the instantaneous center of rotation (ICR), velocity of each tire, heading angle, and simple movement of the cart. The cart is propelled by transaxle brushed DC motor. It is important to approximate an accurate transfer function to represent the motor as the plant module is unavailable. The motor is simulated by using Arduino hardware package in MATLAB®. Rotary encoder is used to record the angular velocity of the shaft. MATLAB® code is created in order to calculate the linear velocity and tabulate the datasets. System Identification Toolbox determines the transfer function of the motor and its performance. The variables measured in experiment to identify the transfer function of the DC motor system are output angular velocity and input voltage. The parameters taken from the DC motor’s mathematical model are derived based on existing literatures. The graph of output velocity against time is plotted and the transfer function is estimated by using System Identification Toolbox in MATLAB®. From the results, it is demonstrated that the motor exhibits second order system

Evaluating mobile laser scanning for landslide monitoring

Landslide is one of the natural disasters that give a huge impact to human life and social-economic development. Landslide needs to be monitored periodically in order to avoid loss of human life and damages of properties. Various methods have been used for monitoring landslide. This aim of the research is to evaluate the potential of mobile laser scanning technique for monitoring of landslide area. The objectives of the research are to acquire three-dimensional surface data of landslide area in different epochs and to analyze the movement of the landslide area using three-dimensional surface deviation and ground surveying techniques. The methodology begins with the GPS survey for the establishment of ground control points for the project area. The total station survey was then carried out to measure the three-dimensional coordinates of twenty well distributed targets located at the project area. The data collection phase was then continuing with the mobile laser scanning survey. The processing of the two epochs data acquired from both techniques was then carried out simultaneously and the methodology concluded with the output comparison analysis for the movement detection of the land slip. The finding shows that the mobile laser scanning provides fast and accurate data acquisition technique of the landslide surface. The surface deviation analysis of the two epochs laser scanning data was capable to detect the movement occurred in the project area. The results were successfully evaluated using the changes of the three-dimensional coordinates of the targets from the two epoch’s ground surveying data

Global patient outcomes after elective surgery: prospective cohort study in 27 low-, middle- and high-income countries.

BACKGROUND: As global initiatives increase patient access to surgical treatments, there remains a need to understand the adverse effects of surgery and define appropriate levels of perioperative care. METHODS: We designed a prospective international 7-day cohort study of outcomes following elective adult inpatient surgery in 27 countries. The primary outcome was in-hospital complications. Secondary outcomes were death following a complication (failure to rescue) and death in hospital. Process measures were admission to critical care immediately after surgery or to treat a complication and duration of hospital stay. A single definition of critical care was used for all countries. RESULTS: A total of 474 hospitals in 19 high-, 7 middle- and 1 low-income country were included in the primary analysis. Data included 44 814 patients with a median hospital stay of 4 (range 2-7) days. A total of 7508 patients (16.8%) developed one or more postoperative complication and 207 died (0.5%). The overall mortality among patients who developed complications was 2.8%. Mortality following complications ranged from 2.4% for pulmonary embolism to 43.9% for cardiac arrest. A total of 4360 (9.7%) patients were admitted to a critical care unit as routine immediately after surgery, of whom 2198 (50.4%) developed a complication, with 105 (2.4%) deaths. A total of 1233 patients (16.4%) were admitted to a critical care unit to treat complications, with 119 (9.7%) deaths. Despite lower baseline risk, outcomes were similar in low- and middle-income compared with high-income countries. CONCLUSIONS: Poor patient outcomes are common after inpatient surgery. Global initiatives to increase access to surgical treatments should also address the need for safe perioperative care. STUDY REGISTRATION: ISRCTN5181700

The International Natural Product Sciences Taskforce (INPST) and the power of Twitter networking exemplified through #INPST hashtag analysis

Background: The development of digital technologies and the evolution of open innovation approaches have enabled the creation of diverse virtual organizations and enterprises coordinating their activities primarily online. The open innovation platform titled "International Natural Product Sciences Taskforce" (INPST) was established in 2018, to bring together in collaborative environment individuals and organizations interested in natural product scientific research, and to empower their interactions by using digital communication tools. Methods: In this work, we present a general overview of INPST activities and showcase the specific use of Twitter as a powerful networking tool that was used to host a one-week "2021 INPST Twitter Networking Event" (spanning from 31st May 2021 to 6th June 2021) based on the application of the Twitter hashtag #INPST. Results and Conclusion: The use of this hashtag during the networking event period was analyzed with Symplur Signals (https://www.symplur.com/), revealing a total of 6,036 tweets, shared by 686 users, which generated a total of 65,004,773 impressions (views of the respective tweets). This networking event's achieved high visibility and participation rate showcases a convincing example of how this social media platform can be used as a highly effective tool to host virtual Twitter-based international biomedical research events