Damage signature of fatigued fabric reinforced plastics in the pulsed ultrasonic polar scan

This study investigates the use of both the amplitude and time-of-flight based pulsed ultrasonic polar scan (P-UPS) for the nondestructive detection and evaluation of fatigue damage in fiber reinforced composites. Several thermoplastic carbon fabric reinforced PPS specimens (CETEX), loaded under various fatigue conditions, have been scanned at multiple material spots according to the P-UPS technique in order to extract material degradation in a quantitative way. The P-UPS results indicate that shear dominated fatigued carbon/PPS goes with a reduction of shear properties combined with large fiber distortions. The P-UPS results of the tension-tension fatigued carbon/PPS samples on the other hand reveal a directional degradation of the stiffness properties, reaching a maximum reduction of -12.8% along the loading direction. The P-UPS extracted damage characteristics are fully supported by simulations, conventional destructive tests as well as visual inspection. The results demonstrate the excellent capability of the P-UPS method for nondestructively assessing and quantifying both shear-dominated and tension-tension fatigue damage in fabric reinforced plastics

Nondestructive monitoring of ageing of Alkali resistant Glass fiber reinforced cement (GRC)

Glass fiber reinforced cement (GRC) is a composite material made of portland cement mortar and alkali resistant (AR) fibers. AR fibers are added to portland cement to give the material additional flexural strength and toughness. However, ageing deteriorates the fibers and as a result the improvement in the mechanical properties resulted from the fiber addition disappears as the structure becomes old. The aim of this paper is monitoring GRC ageing by nondestructive evaluation (NDE) techniques. Two different NDE techniques (1) nonlinear impact resonant acoustic spectroscopy analysis and (2) propagating ultrasonic guided waves are used for this purpose. Both techniques revealed a reduction of the nonlinear behavior in the GRC material with ageing. Specimens are then loaded to failure to obtain their strength and stiffness. Compared to the un-aged specimens, the aged specimens are found to exhibit more linear behavior, have more stiffness but less toughness. Finally, undisturbed fragments on the fracture surface from mechanical tests are inspected under the electron microscope, to understand the fundamental mechanisms that cause the change in the GRC behavior with ageing.The authors want to acknowledge the financial support of the Ministerio de Ciencia e Innovacion MICINN, Spain, and FEDER funding (Ondacem Project: BIA 2010-19933) and BES-2011-044624. Also thanks to PAID-02-11 Program from Universitat Politecnica de Valencia.Eiras Fernández, JN.; Kundu, T.; Bonilla Salvador, MM.; Paya Bernabeu, JJ. (2013). Nondestructive monitoring of ageing of Alkali resistant Glass fiber reinforced cement (GRC). Journal of Nondestructive Evaluation - NDT and E International. 32:300-314. https://doi.org/10.1007/s10921-013-0183-yS30031432Bentur, A., Fibre, M.S.: Reinforced Cementitious Composites, 2nd edn. Taylor and Francis, New York (2007)Purnell, P., Short, N.R., Page, C.L.: A static fatigue model for the durability of glass fibre reinforced cement. J. Mater. Sci. 36(22), 5385–5390 (2001)Ferreira, J.G., Branco, F.A.: Structural application of GRC in telecommunication towers. Constr. Build. Mater. 21(1), 19–28 (2007)Bentur, A., Ben-Bassat, M., Schneider, D.: Durability of glass-fiber-reinforced cements with different alkali-resistant glass fibers. J. Am. Ceram. Soc. 68(4), 203–208 (1985)Cheng, J., Liang, W., Hu, Y., Chen, Q., Frischat, G.H.: Development of a new alkali resistant coating. J. Sol-Gel Sci. Technol. 27(3), 309–313 (2003)Liang, W., Cheng, J., Hu, Y., Luo, H.: Improved properties of GRC composites using commercial E-glass fibers with new coatings. Mater. Res. Bull. 37(4), 641–646 (2002)Payá, J., Bonilla, M., Borrachero, M.V., Monzó, J., Peris-Mora, E., Lalinde, L.F.: Reusing fly ash in glass fibre reinforced cement: a new generation of high-quality GRC composites. Waste Manag. 27(10), 1416–1421 (2007)Zhang, Y., Sun, W., Shang, L., Pan, G.: The effect of high content of fly ash on the properties of glass fiber reinforced cementitious composites. Cem. Concr. Res. 27(12), 1885–1891 (1997)Purnell, P., Short, N., Page, C.: Super-critical carbonation of glass-fibre reinforced cement. Part 1: mechanical testing and chemical analysis. Composites, Part A, Appl. Sci. Manuf. 32(12), 1777–1787 (2001)EN 1170-8:2008. Test method for glass-fibre reinforced cement. Cyclic weathering type testPurnell, P.: Interpretation of climatic temperature variations for accelerated ageing models. J. Mater. Sci. 39(1), 113–118 (2004)Enfedaque, A., Sánchez Paradela, L., Sánchez-Gálvez, V.: An alternative methodology to predict aging effects on the mechanical properties of glass fiber reinforced cements (GRC). Constr. Build. Mater. 27(1), 425–431 (2012)Litherland, K.L., Maguire, P., Proctor, B.A.: A test method for the strength of glass fibres in cement. Int. J. Cem. Compos. Lightweight Concr. 6(1), 39–45 (1984)Itterbeeck, P., Cuypers, H., Orlowsky, J., Wastiels, J.: Evaluation of the strand in cement (SIC) test for GRCs with improved durability. Mater. Struct. 41(6), 1109–1116 (2007)Guyer, R.A., Johnson, P.A.: Nonlinear mesoscopic elasticity: evidence for a new class of materials. Phys. Today 52, 30 (1999)Johnson, P.A.: Nonequilibrium nonlinear dynamics in solids: state of the art. In: Delsanto, P.P. (ed.) Universality of Nonclassical Nonlinearity, pp. 49–69. Springer, New York (2006)Guyer, R.A., McCall, K.R., Boitnott, G.N.: Hysteresis, discrete memory, and nonlinear wave propagation in rock: a new paradigm. Phys. Rev. Lett. 74(17), 3491–3494 (1995)Mayergoyz, I.D.: Mathematical Models of Hysteresis and Their Applications. Academic Press, New York (2003)Van Den Abeele, K.E.A., Carmeliet, J., Ten Cate, J.A., Johnson, P.A.: Nonlinear elastic wave spectroscopy (NEWS) techniques to discern material damage, part II: single-mode nonlinear resonance acoustic spectroscopy. Res. Nondestruct. Eval. 12(1), 31–42 (2000)Chen, J., Jayapalan, A.R., Kim, J.Y., Kurtis, K.E., Jacobs, L.J.: Rapid evaluation of alkali–silica reactivity of aggregates using a nonlinear resonance spectroscopy technique. Cem. Concr. Res. 40(6), 914–923 (2010)Leśnicki, K.J., Kim, J.Y., Kurtis, K.E., Jacobs, L.J.: Characterization of ASR damage in concrete using nonlinear impact resonance acoustic spectroscopy technique. Nondestruct. Test. Eval. Int. 44(8), 721–727 (2011)Bouchaala, F., Payan, C., Garnier, V., Balayssac, J.P.: Carbonation assessment in concrete by nonlinear ultrasound. Cem. Concr. Res. 41(5), 557–559 (2011)Eiras, J.N., Popovics, J.S., Borrachero, M.V., Monzó, J., Payá, J.: Nonlinear impact resonant acoustic spectroscopy to discern mechanical damage in cement based materials. In: 15th International Conference on Experimental Mechanics, Porto, Portugal (2012)Kundu, T.: Ultrasonic Nondestructive Evaluation: Engineering and Biological Material Characterization. CRC Press, Boca Raton (2004)Kundu, T.: Ultrasonic and Electromagnetic NDE for Structure and Material Characterization—Engineering and Biomedical Applications. CRC Press, Boca Raton (2012)Dutta, D., Sohn, H., Harries, K.A., Rizzo, P.: A nonlinear acoustic technique for crack detection in metallic structures. Struct. Health Monit. 8(3), 251–262 (2009)Aymerich, F., Staszewski, W.J.: Impact damage detection in composite laminates using nonlinear acoustics. Composites, Part A, Appl. Sci. Manuf. 41(9), 1084–1092 (2010)EN 1170-1:1998. Precast concrete products. Test method for glass-fibre reinforced cement. Measuring the consistency of the matrix, “Slump test” methodMontgomery, P.L.: A block Lanczos algorithm for finding dependencies over GF(2). In: EUROCRYPT ’95. Lecture Notes in Computer Science, vol. 921, pp. 106–120. Springer, Berlin (1995)EN 1170-5:1998. Precast concrete products. Test method for glass-fibre reinforced cement. Measuring bending strength, “complete bending test” methodRomero, R., Zúnica, L.R.: Métodos Estadísticos en Ingeniería. Universitat Politècnica València, Valencia (2005)Kundu, T.: Fundamentals of Fracture Mechanics. CRC Press, Boca Raton (2008)ASTM C 215:08. Standard Test Method for Fundamental Transverse, Longitudinal, and Torsional Frequencies of Concrete Specimens (2008)Hewlett, P.C.: Lea’s Chemistry of Cement and Concrete, 4th edn. Butterworth-Heinemann, Oxford (2003)Zhu, W., Bartos, P.J.M.: Assessment of interfacial microstructure and bond properties in aged GRC using a novel microindentation method. Cem. Concr. Res. 27(11), 1701–1711 (1997)Purnell, P., Buchanan, A.J., Short, N.R., Page, C.L., Majumdar, A.J.: Determination of bond strength in glass fibre reinforced cement using petrography and image analysis. J. Mater. Sci. 35(18), 4653–4659 (2000)Visalvanich, K., Naaman, A.E.: Fracture model for fiber reinforced concrete. J. ACI Proc. 80(2), 128–138 (1983)Kundu, T., Jang, H.S., Cha, Y.H., Desai, C.S.: A simple model to predict the effect of volume fraction, diameter, and length of fibers on strength variation of fiber reinforced brittle matrix composites. Int. J. Numer. Anal. Methods Geomech. 24, 655–673 (2000)Li, V.C., Maalej, M.: Toughening in cement based composites. Part II: fiber reinforced composites. Cem. Concr. Compos. 18, 239–249 (1996)Van Den Abeele, K.E.A., Johnson, P.A., Sutin, A.: Nonlinear elastic wave spectroscopy (NEWS) techniques to discern material damage, part I: nonlinear wave modulation spectroscopy (NWMS). Res. Nondestruct. Eval. 12(1), 17–30 (2000

Drivers and impact of antifungal therapy in critically ill patients with Aspergillus-positive respiratory tract cultures

Invasive pulmonary aspergillosis (IPA) is an increasingly recognised problem in critically ill patients. Little is known about how intensivists react to an Aspergillus-positive respiratory sample or the efficacy of antifungal therapy (AFT). This study aimed to identify drivers of AFT prescription and diagnostic workup in patients with Aspergillus isolation in respiratory specimens as well as the impact of AFT in these patients. ICU patients with an Aspergillus-positive respiratory sample from the database of a previous observational, multicentre study were analysed. Cases were classified as proven/putative IPA or Aspergillus colonisation. Demographic, microbiological, diagnostic and therapeutic data were collected. Outcome was recorded 12 weeks after Aspergillus isolation. Patients with putative/proven IPA were more likely to receive AFT than colonised patients (78.7% vs. 25.5%; P 7) (68.4% vs. 36.9%) (both P < 0.001). Once adjusted for disease severity, initiation of AFT did not alter the odds of survival (HR = 1.40, 95% CI 0.89–2.21). Likewise, treatment within 48 h following diagnosis did not change the clinical outcome (75.7% vs. 61.4%; P = 0.63). Treatment decisions appear to be based on diagnostic criteria and underlying disease severity at the time of Aspergillus isolation. IPA in this population has a dire prognosis and AFT is not associated with reduced mortality. This may be explained by delayed diagnosis and an often inevitable death due to advanced multiorgan failure

Ambient-aware continuous care through semantic context dissemination

Background: The ultimate ambient-intelligent care room contains numerous sensors and devices to monitor the patient, sense and adjust the environment and support the staff. This sensor-based approach results in a large amount of data, which can be processed by current and future applications, e. g., task management and alerting systems. Today, nurses are responsible for coordinating all these applications and supplied information, which reduces the added value and slows down the adoption rate. The aim of the presented research is the design of a pervasive and scalable framework that is able to optimize continuous care processes by intelligently reasoning on the large amount of heterogeneous care data. Methods: The developed Ontology-based Care Platform (OCarePlatform) consists of modular components that perform a specific reasoning task. Consequently, they can easily be replicated and distributed. Complex reasoning is achieved by combining the results of different components. To ensure that the components only receive information, which is of interest to them at that time, they are able to dynamically generate and register filter rules with a Semantic Communication Bus (SCB). This SCB semantically filters all the heterogeneous care data according to the registered rules by using a continuous care ontology. The SCB can be distributed and a cache can be employed to ensure scalability. Results: A prototype implementation is presented consisting of a new-generation nurse call system supported by a localization and a home automation component. The amount of data that is filtered and the performance of the SCB are evaluated by testing the prototype in a living lab. The delay introduced by processing the filter rules is negligible when 10 or fewer rules are registered. Conclusions: The OCarePlatform allows disseminating relevant care data for the different applications and additionally supports composing complex applications from a set of smaller independent components. This way, the platform significantly reduces the amount of information that needs to be processed by the nurses. The delay resulting from processing the filter rules is linear in the amount of rules. Distributed deployment of the SCB and using a cache allows further improvement of these performance results

Postoperative Staphylococcus aureus Infections in Patients With and Without Preoperative Colonization

Importance Staphylococcus aureus surgical site infections (SSIs) and bloodstream infections (BSIs) are important complications of surgical procedures for which prevention remains suboptimal. Contemporary data on the incidence of and etiologic factors for these infections are needed to support the development of improved preventive strategies.Objectives To assess the occurrence of postoperative S aureus SSIs and BSIs and quantify its association with patient-related and contextual factors.Design, Setting, and Participants This multicenter cohort study assessed surgical patients at 33 hospitals in 10 European countries who were recruited between December 16, 2016, and September 30, 2019 (follow-up through December 30, 2019). Enrolled patients were actively followed up for up to 90 days after surgery to assess the occurrence of S aureus SSIs and BSIs. Data analysis was performed between November 20, 2020, and April 21, 2022. All patients were 18 years or older and had undergone 11 different types of surgical procedures. They were screened for S aureus colonization in the nose, throat, and perineum within 30 days before surgery (source population). Both S aureus carriers and noncarriers were subsequently enrolled in a 2:1 ratio.Exposure Preoperative S aureus colonization.Main Outcomes and Measures The main outcome was cumulative incidence of S aureus SSIs and BSIs estimated for the source population, using weighted incidence calculation. The independent association of candidate variables was estimated using multivariable Cox proportional hazards regression models.Results In total, 5004 patients (median [IQR] age, 66 [56-72] years; 2510 [50.2%] female) were enrolled in the study cohort; 3369 (67.3%) were S aureus carriers. One hundred patients developed S aureus SSIs or BSIs within 90 days after surgery. The weighted cumulative incidence of S aureus SSIs or BSIs was 2.55% (95% CI, 2.05%-3.12%) for carriers and 0.52% (95% CI, 0.22%-0.91%) for noncarriers. Preoperative S aureus colonization (adjusted hazard ratio [AHR], 4.38; 95% CI, 2.19-8.76), having nonremovable implants (AHR, 2.00; 95% CI, 1.15-3.49), undergoing mastectomy (AHR, 5.13; 95% CI, 1.87-14.08) or neurosurgery (AHR, 2.47; 95% CI, 1.09-5.61) (compared with orthopedic surgery), and body mass index (AHR, 1.05; 95% CI, 1.01-1.08 per unit increase) were independently associated with S aureus SSIs and BSIs.Conclusions and Relevance In this cohort study of surgical patients, S aureus carriage was associated with an increased risk of developing S aureus SSIs and BSIs. Both modifiable and nonmodifiable etiologic factors were associated with this risk and should be addressed in those at increased S aureus SSI and BSI risk

Relativistic corrections in (gamma,N) knockout reactions

We develop a fully relativistic DWIA model for photonuclear reactions using the relativistic mean field theory for the bound state and the Pauli reduction of the scattering state which is calculated from a relativistic optical potential. Results for the 12C(gamma,p) and 16O(gamma,p) differential cross sections and photon asymmetries are displayed in a photon energy range between 60 and 257 MeV, and compared with nonrelativistic DWIA calculations. The effects of the spinor distortion and of the effective momentum approximation for the scattering state are discussed. The sensitivity of the model to different prescriptions for the one-body current operator is investigated. The off-shell ambiguities are large in (gamma,p) calculations, and even larger in (gamma,n) knockout.Comment: LaTeX2e, 18 pages, and 6 figure

Characterization of hysteretic stress-strain behavior using the integrated Preisach density

In this paper, we introduce the concept of Integrated Preisac–Mayergoyz (IPM) density to analyze static uniaxial compression tests at values well below the critical strength, and to characterize the elasticity of materials with hysteresis in their stress–strain relationship. The IPM density can be deduced from a particular force protocol following basic data treatment. The advantage of the IPM density over prior approaches is that no second order differentiation of the data is required which reduces the errors and uncertainties typical for past practice in the specific context of rock elasticity using scanning curves and PM density analysis. The characterization of the elasticity of the material is established in terms of a non-hysteretic strain contribution in the form of a non-linear but reversible equation of state, and a hysteretic contribution represented by the IPM density. The IPM inversion procedure is tested for simulated stress–strain data subjected to additive noise, and the results are compared to the traditional methodology. In addition, we analyze the hysteretic and non-hysteretic characteristics of five natural building stones, and show evidence for a classification based on the inferred properties.status: publishe