30 research outputs found
Recommended from our members
Effect of surface state and material on surface quality enhancement by Dual Laser Powder Bed Fusion
Parts produced by Laser Powder Bed Fusion typically exhibit a limited surface quality often requiring
systematic post-processing. The KU Leuven AM team recently developed a Dual Laser Powder Bed Fusion
strategy to improve the quality of inclined up-facing surfaces during building. It consists of two steps: (1) a pulsed
laser induces shock waves to remove powder from inclined surfaces, followed by (2) in-situ laser remelting of
the newly exposed surfaces. The first part of this paper covers the powder removal efficiency using shock waves
depending on the used material. A design of experiments was performed for horizontal samples of tool steels,
titanium and aluminium alloys. The second part deals with the effect of the initial surface state on the powder
removal efficiency for inclined surfaces (SaR,LT60=16.2 µm, SaR,LT120=24.0 µm). Finally, the third part
demonstrates the surface quality improvement, resulting in a reduction of Ra up to 61% for 15° inclinations.Mechanical Engineerin
Recommended from our members
HIGH SPEED VIDEO IMAGING OF OVERHANG SURFACES IN BEAM SHAPED LASER POWDER BED FUSION OF 316L STAINLESS STEEL
Beam shaping has seen rising interest in the AM industry and research field because of the increased level of
control over the spatial distribution of the thermal input during Laser Powder Bed Fusion, allowing for faster
build rates. This report investigates if the more uniform heat input offers benefits to the scanning of unsupported
overhanging structures. In-situ high speed video imaging is combined with post process surface characterization
to derive a relation between the scan parameters and quality of the overhang surface. The best results were
achieved at low energy densities, but no clear advantage of top-hat shaped laser spots over the standard Gaussian
beams is observed.Mechanical Engineerin
Recommended from our members
TOWARDS THE LIMITS IN COPPER LATTICE PRODUCTION VIA FIBER LASER POWDER BED FUSION
Additive manufacturing of copper, by means of Laser Powder Bed Fusion (LPBF), paves the way for
innovation in thermal systems and heat transfer devices. Recent simulations have shown that by interchanging
typical fin designs with more complex structures, an overall improvement in pressure drop and weight can be
obtained while offering the same thermal performance. Here, small-scale lattice structures are especially of
interest for AM as they form a reliable, periodic infill. However, until now, their study has been mainly theoretical.
To analyze these structures in more detail, an in-house built LPBF machine at KU Leuven has been successfully
used to manufacture pure copper parts. Measurements showed a conductivity exceeding 100%IACS, which is the
result of low contamination and low porosity in the as-built material. In this work, the parameter optimization for
thin-walled lattices is discussed, the limitations in terms of minimal feature size are described and physical
mechanisms behind these limitations are uncovered.Mechanical Engineerin
Understanding elastic anisotropy in diamond based lattice structures produced by laser powder bed fusion: Effect of manufacturing deviations
Laser powder bed fusion (L-PBF) allows the production of metal lattice cellular structures with tailored mechanical properties. In order to generate the specific structural behavior it is of utmost importance to understand the
response of the unit cells when different load conditions are considered. In this article the mechanical response of
diamond based cellular structures has been investigated focusing on the impact of geometrical inaccuracy generated by the manufacturing process on the elastic anisotropy of the mentioned unit cell. The μ-CT analysis of
the structures shows that the manufacturing deviations occur in certain orientations that depend highly on the
building direction and proximity to nodes. The measured imperfection types were implemented in a finite element model in order to predict their single and combined effects in the elastic directional response. The results
indicate that the L-PBF process can induce a significant change of elastic anisotropy in the diamond unit cells, including a substantial variation of the optimal orientation for minimal compliance. Methods are presented to calculate this anisotropy such that it can be taken into account when designing and using such lattice structures in
real-life applications with multi-axial load condition
Recommended from our members
PROCESS AND MATERIAL OPTIMISATIONS FOR INTEGRATION OF CHOPPED GLASS FIBRES IN LASER SINTERED POLYMER PARTS
Additively manufactured polymer composites gain popularity in a variety of industries such as aerospace,
biomedical and automotive. Laser sintering (LS) is a well-known AM process that typically uses polyamide which
can serve as matrix material. Hence LS has the potential to produce reinforced polymers that can meet demanding
requirements. In previous research, issues with powder flowability and poor fibre dispersion led to limited
increase of mechanical properties. To overcome this, a novel fibre deposition system was recently developed and
optimised at KU Leuven to successfully produce fibre reinforced LS samples with random inter- and intralayer
fibre orientations. A limited but promising influence of deposited glass fibres on produced LS parts was noted
after mechanical testing. In this work, the influence of different (heat) treatments on glass fibres used during LS
will be discussed as well as the resulting differences in the fibre/matrix behaviour as analysed through hot stage
microscopy.Mechanical Engineerin
Emergence of 3D Printed Dosage Forms: Opportunities and Challenges
The recent introduction of the first FDA approved 3D-printed drug has fuelled interest in 3D printing technology, which is set to revolutionize healthcare. Since its initial use, this rapid prototyping (RP) technology has evolved to such as extent that it is currently being used in a wide range of applications including in tissue engineering, dentistry, construction, automotive and aerospace. However, in the pharmaceutical industry this technology is still in its infancy and its potential yet to be fully explored.
This paper presents various 3D printing technologies such as stereolithographic, powder based, selective laser sintering, fused deposition modelling and semi-solid extrusion 3D printing. It also provides a comprehensive review of previous attempts at using 3D printing technologies on the manufacturing dosage forms with a particular focus on oral tablets. Their advantages particularly with adaptability in the pharmaceutical field have been highlighted, including design flexibility and control and manufacture which enables the preparation of dosage forms with complex designs and geometries, multiple actives and tailored release profiles. An insight into the technical challenges facing the different 3D printing technologies such as the formulation and processing parameters is provided. Light is also shed on the different regulatory challenges that need to be overcome for 3D printing to fulfil its real potential in the pharmaceutical industry
The KU Leuven student electric car project: From theory to practice
© 2014, FISITA. All rights reserved. The main purpose of this work is to indicate how engineering students can be educated in a project-based framework in order to develop important competences such as working in team, practical problem solving, decision making and bridging the gap between theory and practice. These skills are crucial for all engineering students and project-based education in an effective way for student to learn these competences.status: publishe
Recommended from our members
Fused Filament Fabrication on the Moon
Additive manufacturing (AM) techniques possess the capabilities to rapidly produce complex
and customised parts, typically in low-volume and with reduced material us- age and preparation
tools . These attributes magnify their indispensability when the availability of materials and
equipment is limited. It can be such a case for off-Earth manufacturing, e.g. in manned lunar
explorations. This article presents a preliminary discussion on the possibility of performing fused
filament fabrication (FFF) on the Moon from the perspective of heat transfer in printed parts. It
makes use of experimen- tal data and simulations to quantify the significance of each heat
transfer mechanism taking place during printing. The quantification then enables us to
investigate how the lunar environment affects the cooling in the printed parts. Finally, FFF on
the Moon is predicted to be feasible. Yet, apparent differences in the process window and types
of applications are pointed out as compared with the counterpart printing activities on the Earth.
The full paper may be found in a special issue of the TMS publication JOM, March 2022.Mechanical Engineerin
Thermography based in-process monitoring of Fused Filament Fabrication of polymeric parts
© 2019 CIRP Temperature management is crucial in Fused Filament Fabrication (FFF). This paper presents an infrared based set-up able to record spatial and temporal variations during printing of an FFF part, with a field of view of (21.7 × 14.9)mm 2 and at spatial resolution of 30.2 μm. The system is experimentally verified and the captured temperature profiles are compared to numerical data, obtained via an own-developed FFF numerical model. This work is a first step towards a combined experimental-numerical approach for in-process monitoring of FFF, with implications for filament developers, machine builders and (end-)users, ultimately demanding high quality (certified)parts.status: publishe
Recommended from our members
Laser Sintering of PA12/PA4,6 Polymer Composites
This work investigates the laser sintering (LS) processing of polyamide-12/polyamide-4,6
composites and the performance of resulting parts. The coalescence and consolidation of the
PA12/PA4,6 powder mixture are characterized. This demonstrates that at the LS processing
window for PA12 (grade PA2200), the powder mixture exhibits bimodal melting behavior. In this
behavior PA2200 melts during LS processing but PA4,6 remains solid. After laser sintering of the
materials, the microstructure and the mechanical properties of the resulting parts are characterized.
This illustrates that the PA2200 coalesces well and PA4,6 remains as a secondary phase during the
LS processing. Further developments to improve the powder size and morphology in order to
obtain better relative density of the parts are necessary. The investigated processing approach
opens up new perspectives for LS of advanced engineering thermoplastics.Mechanical Engineerin