68 research outputs found
Verification of estimation of long-term creep properties of 9-12%Cr steel in a shorter time interval
Na žárupevných 9-12 %Cr ocelích byla ověřována závislosti doby do lomu na teplotě, přičemž napětí bylo shodné při všech zkouškách. Zvolené oceli se v současné době stále více
používají, a to především v energetice, kde jsou využity jejich dobré mechanické vlastnosti při
vysokých teplotách. Na základě takto získaných dat lze z krátkých creepových zkoušek spolehlivěji odhadnout doby do lomu u řádově delších zkoušek, které jsou požadovány při přejímacích
podmínkách. Výsledky byly získány při spolupráci společností SVÚM a.s. a ŽĎAS a.s. za podpory TA ČR.TA ČRThe dependence of time to fracture on temperature was verified on high temperature
9-12 %Cr steels, while the stress was the same in all tests. These steels are currently used in the
energy industry, where their good mechanical properties at high temperatures are utilized.
Based on the obtained data, the times to fracture can be more reliably estimated from short
creep tests for much longer tests, which are required under acceptance conditions. The results
were obtained in cooperation with SVÚM a.s. and ŽĎAS a.s. with the support of TA CR
The effect of processing route on properties of HfNbTaTiZr high entropy alloy
High entropy alloys (HEA) have been one of the most attractive groups of materials for researchers in the last several years. Since HEAs are potential candidates for many (e.g., refractory, cryogenic, medical) applications, their properties are studied intensively. The most frequent method of HEA synthesis is arc or induction melting. Powder metallurgy is a perspective technique of alloy synthesis and therefore in this work the possibilities of synthesis of HfNbTaTiZr HEA from powders were studied. Blended elemental powders were sintered, hot isostatically pressed, and subsequently swaged using a special technique of swaging where the sample is enveloped by a titanium alloy. This method does not result in a full density alloy due to cracking during swaging. Spark plasma sintering (SPS) of mechanically alloyed powders resulted in a fully dense but brittle specimen. The most promising result was obtained by SPS treatment of gas atomized powder with low oxygen content. The microstructure of HfNbTaTiZr specimen prepared this way can be refined by high pressure torsion deformation resulting in a high hardness of 410 HV10 and very fine microstructure with grain size well below 500 nm.Web of Science1223art. no. 402
Influence of technology innovation on creep properties of steels
Ve spolupráci společností SVÚM a.s. a ŽĎAS, a.s. byl ověřován vliv zavedení moderní vakuové technologie při výrobě tekutého kovu. Mechanické, a především dlouhodobé creepové
vlastnosti, byly porovnány u žárupevných CrMo a CrMoV ocelích, vyrobených dvěma různými
technologiemi. Původní, ale stále používanou metodou je zpracování tekutého kovu pomocí
elektrické obloukové pece (EOP). Druhou variantou je výroba pomocí moderní vakuové technologie (EOP/LF/VD). Pro mechanické zkoušky byly použity lité a tvářené varianty 3 různých
ocelí.Výsledky mechanických a creepových zkoušek byly získány v rámci projektu TAČR
TH03020028 s názvem „Výzkum a vývoj vlivu moderních vakuovacích metalurgických po-
stupů výroby tekutého kovu na vlastnosti žárupevných ocelí“.The influence of introducing modern vacuum technology in the production of liquid metal
was verified in cooperation with SVÚM a.s. and ŽĎAS, a.s. The mechanical and especially the
long-term creep properties were compared for CrMo and CrMoV steels, produced by two different technologies. An original but still used method is the processing of liquid metal using an
electric arc furnace (EOP). The second variant is production using modern vacuum technology
(EOP/LF/VD). Mechanical tests were performed on cast and forged variants of 3 different
steel
High temerature properties of steel CB2 in basic condition and after welding
Příspěvek popisuje creepové vlastnosti ocele CB2. Tyto vlastnosti se v dostupné literatuře
téměř nevyskytují. Ve SVÚM, a.s. byl testován materiál vyrobený firmou ŽĎAS, a.s. V rámci
spolupráce byly zkoušeny krátkodobé mechanické vlastnosti a dlouhodobé creepové vlastnosti
základního materiálu. Článek se zaměřuje především na žárupevné vlastnosti ocele CB2 a na
jejich ovlivnění homogenním svarovým spojem.This paper describes creep properties of CB2 steel. These properties are almost absent in the
available literature. In SVUM, a.s. was tested the material produced by ŽĎAS, a.s. Shortterm
mechanical properties and long-term creep properties of the base material were tested during
the cooperation. The paper focuses mainly on the creep properties of CB2 steel and on their
influence on the homogeneous weld
Mechanical properties of martenzitic steel CB2
Martenzitická ocel CB2 (GX13CrMoCoVNbNB-1011) je výsledkem dlouhodobého
výzkumu, který proběhl v rámci mezinárodní evropské spolupráce programu COST 536.
Vlastnosti materiálu CB2 jsou v dostupné literatuře popsány jen velmi málo. Studium
mechanických vlastností, včetně dlouhodobějšího creepového chování, ocele CB2 bylo
provedeno ve spolupráci SVÚM, a.s. a ŽĎAS, a.s. V předloženém příspěvku jsou shrnuty
výsledky tohoto experimentálního výzkumu.Martensitic steel CB2 (GX13CrMoCoVNbNB-1011) is the result of research conducted in
international European cooperation COST. Little information on the CB2 material properties
is in the literature. The study of mechanical properties, including long-term creep behaviour
of steel CB2 was carried out in cooperation with SVÚM, a.s. and ŽĎAS, a.s. The presented
paper summarizes the results of this experimental research
Influence of forging on mechanical and creep properties of martensitic steel
V rámci ověřování výrobní technologie byl na martenzitických ocelích P91 a P92 studován
vliv tváření na mechanické a creepové vlastnosti. Z ingotů obou materiálů byly vykovány osazené hřídele o různém průměru. Stupeň prokování se pohyboval od Pk = 3 do Pk = 13 v případě
oceli P91 a od Pk = 11,6 do Pk = 24,2 u oceli P92. Výsledky byly získány při spolupráci společností SVÚM a.s. a ŽĎAS a.s. za podpory TA ČR.The influence of forming on mechanical and creep properties was studied on the P91 and
P92 martensitic steels as part of the verification of production technology. Shoulder shafts of
different diameters were forged from ingots of both materials. The degree of forging varied
from Pk = 3 to Pk = 13 for P91 and from Pk = 11,6 to Pk = 24,2 for P92. The results were obtained
in cooperation with SVÚM a.s. and ŽĎAS a.s. with the support of TA ČR
Foundation and incorporation of a European company by merger
Katedra obchodního právaDepartment of Business LawFaculty of LawPrávnická fakult
Changes in volume of water reservoir Fojtka due to sediment flux
Sedimentation in dams is a natural process depending on various factors over a period of time. Sediments influence both total capacity of dam's surface and also relief of bottom.
This thesis deals with amount of sediment in Fojtka dam and with change of its bottom's relief in past 109 years since its establishment. There was conducted measuring using an echosounder in a boat. Final output derived from this experiment was a point layer including 5500 point items. Subsequently there was executed a measurement of dam's shoreline using GPS device. Data were processed in ArcGIS software, then reduced and edited to be used for interpolation tools of ArcToolbox. In order to select the most accurate interpolation method, there were created validation data, which were compared with interpolated data. The best results have been achieved by interpolation method Kriging and TIN in resolution 0.5 m.
Original maps were vectorized for comparison with current condition. Created validation data were compared in order to show accuracy of particular interpolation. The most useful evaluated method for gained data was TIN method in resolution 0.5 m. TIN method was applied in both data sets for 2D and 3D bottom relief visualization and also for calculation of actual water volume and area of water surface of the dam.
Difference in bottom's relief of Fojtka dam showed capacity reduction about 6,7 % and reduction of water surface area about 3,2 %. Regular extracting of sediment in reservoir located above the dam causes this relatively small silting ratio
Possibilities of sales promotion of travel insurance based on data analysis of social networks
This bachelor work mainly focuses on a sale support of travel insurance, which is based on data from the Facebook. There are 2 methods used, selection of specific users for a direct offer and identification of the influencers. The work consists of 5 goals. In the first one there are important key words specified, the second goal is to describe the attitudes to the classification of users, the third goal is to describe the offer of travel insurance on the market, the fourth goal is to suggest the attitude to dealing with the problem and the last one is to clarify the attitude on data.In the theoretical part there are important terms in this field described. I also do the re-search on possible methods of classification including their advantages and disad-vantages. I also explain the principles of insurance and travel insurance in detail, where there are also 5 Czech bank offers described. In the practical part there are 2 methods suggested, which are applied on data available.Práce se zabývá podporou prodeje cestovního pojištění na základě dat z Facebooku. Pou-žity jsou 2 metody, vybrání konkrétních uživatelů k přímému oslovení a identifikace vlivných osob. Práce má celkem 5 cílů. Prvním z nich je vymezení důležitých pojmů, druhým cílem je popis přístupů ke klasifikaci uživatelů, třetím cílem je popis trhu ces-tovního pojištění, čtvrtým cílem je navrhnout přístup k řešení problému a poslední cíl je ověření přístupu na datech.V teoretické části popisuji důležité pojmy z dané oblasti. Dále zkoumám možné metody klasifikace včetně jejich výhod a záporů. Objasňuji systém pojištění a cestovní pojištění podrobněji včetně popisu nabídek cestovního pojištění 5 českých bank. V praktické části jsou navrženy 2 metody, které na dostupných datech následně využívám
The Synchronized Multimedia Integration Language and web multimedia presentation
The aim of this Bachelor work is to create a user guide of SMIL technology as a modern method for creation of web multimedia presentations. Furthermore, I tried to compare these three technologies: SMIL, Flash and JavaScript. The work also contains the specific web multimedia presentation which was created by means of SMIL technology
- …