8 research outputs found

    Prevalence, associated factors and outcomes of pressure injuries in adult intensive care unit patients: the DecubICUs study

    Get PDF
    Funder: European Society of Intensive Care Medicine; doi: http://dx.doi.org/10.13039/501100013347Funder: Flemish Society for Critical Care NursesAbstract: Purpose: Intensive care unit (ICU) patients are particularly susceptible to developing pressure injuries. Epidemiologic data is however unavailable. We aimed to provide an international picture of the extent of pressure injuries and factors associated with ICU-acquired pressure injuries in adult ICU patients. Methods: International 1-day point-prevalence study; follow-up for outcome assessment until hospital discharge (maximum 12 weeks). Factors associated with ICU-acquired pressure injury and hospital mortality were assessed by generalised linear mixed-effects regression analysis. Results: Data from 13,254 patients in 1117 ICUs (90 countries) revealed 6747 pressure injuries; 3997 (59.2%) were ICU-acquired. Overall prevalence was 26.6% (95% confidence interval [CI] 25.9–27.3). ICU-acquired prevalence was 16.2% (95% CI 15.6–16.8). Sacrum (37%) and heels (19.5%) were most affected. Factors independently associated with ICU-acquired pressure injuries were older age, male sex, being underweight, emergency surgery, higher Simplified Acute Physiology Score II, Braden score 3 days, comorbidities (chronic obstructive pulmonary disease, immunodeficiency), organ support (renal replacement, mechanical ventilation on ICU admission), and being in a low or lower-middle income-economy. Gradually increasing associations with mortality were identified for increasing severity of pressure injury: stage I (odds ratio [OR] 1.5; 95% CI 1.2–1.8), stage II (OR 1.6; 95% CI 1.4–1.9), and stage III or worse (OR 2.8; 95% CI 2.3–3.3). Conclusion: Pressure injuries are common in adult ICU patients. ICU-acquired pressure injuries are associated with mainly intrinsic factors and mortality. Optimal care standards, increased awareness, appropriate resource allocation, and further research into optimal prevention are pivotal to tackle this important patient safety threat

    Electronic energy level alignment of dye molecules on TiO2 and ZnO surfaces for photovoltaic applications:

    No full text
    In dye-sensitized solar cells (DSSC), the attributes of the dye-semiconductor interface are of important interest. In this thesis, electronic and structural aspects of dye/semiconductor systems have been studied experimentally using ultraviolet photoemission spectroscopy (UPS), inverse photo electron spectroscopy (IPS) and scanning tunneling microscopy (STM). In this work the electronic structure of N3, or more precisely Ru(4,4-dicarboxylate-2,2-bipyridine)2-(NCS)2, molecules absorbed on rutile TiO2(110) single crystal and anatase TiO2 nanoparticles has been studied and has shown that the energy of highest occupied molecular orbital (HOMO) of the N3 dye is located near the middle of the semiconductor band gap and that the lowest unoccupied molecular orbital (LUMO) level overlaps with the Ti 3d orbitals of the TiO2 conduction band. A shift of the UPS/IPS energy spectra indicates the formation of an induced dipole upon N3 adsorption on the TiO2 surface. The electronic contributions of N3 in combination with ZnO are similar to N3 absorbed on TiO2. The position of the HOMO is almost identical in regard to the band edge of the valence band, but the LUMO is located a bit higher in energy in regard the conduction band minimum (CBM) as in comparison with N3/TiO2. We studied also the adsorbate isonicotinic acid (INA) with chemical structure: C6H5NO2 on the oxides, because it is a good model for the binding ligand of the N3 molecule and which is where the spatial distribution of the N3 LUMO is expected to be delocalized. Indeed, the electronic structure of the LUMO for INA adsorbate is for both semiconductors is very similar to the LUMO of the adsorbate N3 dye. Another dye, catechol (C6H6O2), has been reported that catechol bonds strongly to TiO2 and that electrons can be excited directly from the catechol HOMO to the conduction band of TiO2. Our experiments show that the LUMO is indeed mixed significantly with the conduction band of TiO2. A monolayer of pivalate ((CH3)3CCOO-) ions was used to protect the sample surface from contamination during the wetting process of the N3 adsorption. The effect of passivation on the quality of the semiconductor/dye interface is studied by UPS and IPS measurements.M.S.Includes bibliographical references (p. 83-87)by Jean-Patrick Theise

    Lock-in thermography as a tool for quality control of photovoltaic modules

    No full text
    In this short communication, we present a method which utilizes contactless ILIT (illuminated lock-in thermography) measurement of a photovoltaic (PV) module and image postprocessing in order to calculate the peak power Pmpp of the module and to study the influence of local defects on the module performance. In total, 103 Copper-Indium-Gallium-Diselenide (CIGS) modules were investigated and the results showed a good correlation (mean error less than 6%) between the calculated IR-signal and the measured Pmpp. We performed our study on CIGS modules but the presented approach is not restricted to CIGS modules. The method provides a valuable tool for PV quality control

    Correction to: Prevalence, associated factors and outcomes of pressure injuries in adult intensive care unit patients: the DecubICUs study (Intensive Care Medicine, (2021), 47, 2, (160-169), 10.1007/s00134-020-06234-9)

    No full text
    The original version of this article unfortunately contained a mistake. The members of the ESICM Trials Group Collaborators were not shown in the article but only in the ESM. The full list of collaborators is shown below. The original article has been corrected
    corecore