Model and experiments to determine lubricant film formation and frictional torque in aircraft landing gear pin joints

Pin joints are found in many large articulating structures. They tend to be under high load and articulate slowly; so, the joints typically operate in the boundary or mixed lubrication regimes. This means that the operating torque depends on the respective proportions of liquid and solid contact between the joint mating faces. In this article, a mixed lubrication model of a grease-lubricated landing gear joint is established to determine a theoretical Stribeck curve, frictional torque and lubricant film thickness under different loads. Parameters describing pin joint working conditions, geometry, lubricant properties and pin/bush texture are used. The model can also predict the proportion of the load that is supported by contacting asperities and lubricant film. The changing proportions of these two parts indicate transformations between different lubrication regimes. Experiments on an instrumented pin joint have been carried out to compare with the predicted friction and torque performance. Theoretical calculation results show good consistency with experimental plots at high load. But under low load, the real friction between pin and bush is significantly lower than theoretical predictions

The Tribological Behaviour of Carbon Fibre Reinforced Polyaryletherketones (PAEKs) through their Glass Transitions.

yesAdvanced engineering polymers of the Polyaryletherketone (PAEK) family with carbon fibre reinforcement are finding application in engineering systems as tribological bearing surfaces under severe operating conditions that cyclically move the polymer into and beyond the glass transition temperature region. To support such an application, the friction in high speed and low load PAEK-steel sliding contacts was investigated both unlubricated and lubricated with a trinonyl trimellitate ester, a base fluid for high temperature industrial lubricants. Four polymers in the PAEK family, PEEK, PEK, PEKEKK and PEKK, with 30%wt of carbon fibre whiskers were tested against an AISI 4140 steel disc. When unlubricated, low friction depended upon the formation of a PAEK transfer film on the steel disc and when this became unstable in the glass transition region the friction increased to much higher levels with associated polymer surface damage. Frictional heating due to the high sliding speed dominated the differences in glass transition behaviour between the four PAEKs. When lubricated, the lubricant film controlled friction and there was no significant effect of the glass transition of any of the PAEKs. The irreversible nature of the glass transition in PAEKs in such tribological applications, due to high surface damage at high temperature, means that it is essential to ensure effective lubrication in both fluid film and boundary lubrication.Innovate UK, Knowledge Transfer Partnershi

Friction and wear properties of nano-Si<inf>3</inf>N<inf>4</inf>/nano-SiC composite under nanolubricated conditions

Friction and wear properties of nano-Si3N4/nano-SiC composite were studied under nanolubricated conditions. Mineral oil mixed with nanoparticles of diamond was used as lubricant. A friction coefficient of 0.043 and a wear coefficient of 4.2×10-7 were obtained for nano-Si3N4/nano-SiC composite under normal load of 600 N with mineral oil + 0.5 wt% nanodiamond, whereas a friction coefficient of 0.077 and a wear coefficient of 10.3×10-7 were obtained for nano-Si3N4/nano-SiC composite under normal load of 600 N with mineral oil. 3D surface profilometer was used to study the surface morphology of wear scars. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) studies were conducted to illustrate reduction in friction and wear

Variational Methods for Biomolecular Modeling

Structure, function and dynamics of many biomolecular systems can be characterized by the energetic variational principle and the corresponding systems of partial differential equations (PDEs). This principle allows us to focus on the identification of essential energetic components, the optimal parametrization of energies, and the efficient computational implementation of energy variation or minimization. Given the fact that complex biomolecular systems are structurally non-uniform and their interactions occur through contact interfaces, their free energies are associated with various interfaces as well, such as solute-solvent interface, molecular binding interface, lipid domain interface, and membrane surfaces. This fact motivates the inclusion of interface geometry, particular its curvatures, to the parametrization of free energies. Applications of such interface geometry based energetic variational principles are illustrated through three concrete topics: the multiscale modeling of biomolecular electrostatics and solvation that includes the curvature energy of the molecular surface, the formation of microdomains on lipid membrane due to the geometric and molecular mechanics at the lipid interface, and the mean curvature driven protein localization on membrane surfaces. By further implicitly representing the interface using a phase field function over the entire domain, one can simulate the dynamics of the interface and the corresponding energy variation by evolving the phase field function, achieving significant reduction of the number of degrees of freedom and computational complexity. Strategies for improving the efficiency of computational implementations and for extending applications to coarse-graining or multiscale molecular simulations are outlined.Comment: 36 page

Effect of crosslinking on the microtribological behavior of model polymer brushes

Polymer brushes in good solvents are known to exhibit excellent tribological properties. We have modeled polymer brushes and their gels using a multibead-spring model and studied their tribological behavior via nonequilibrium molecular-dynamics (MD) simulations. Simulations of brush- against-wall systems were performed using an implicit solvent-based approach. Polymer chains were modeled as linear chains, randomly grafted on a planar surface. Quantities extracted from the simulations are the normal stress, shear stress and concentration profiles. We find that while an increase in the degree of crosslinking leads to an increase in the coefficient of friction, an increase of the length of crosslinker chains does the opposite. Effect of crosslinking can be understood in two ways: (i) there are fewer polymer chains in the outer layer as the degree of crosslinking increases to take part in brush-assisted lubrication, and (ii) crosslinked polymer chains are more resistant to shear than non-crosslinked ones

Protic Ionic Liquids Used as Metal-Forming Green Lubricants for Aluminum: Effect of Anion Chain Length

Among the applications for protic ionic liquids (PILs), lubrication is one of the newest and the most promising. In this work, ammonium-based protic ionic liquids were tested as lubricant fluids for aluminum-steel contacts. PILs were synthesized with 2-hydroxyethylamine (2HEA) and a carboxylic acid (formic and pentanoic), aiming to understand the effect of two different anion chain lengths on the lubricant behavior. The synthesized PILs were characterized by RMN, FTIR and TGA. Wear tests, conducted using a ball-on-plate configuration, showed that the increase of the anion carbon chain length in the PIL structure reduced significantly the coefficient of friction value. Besides, after the wear tests, the PILs structural integrity was not affected. In the same way, bending under tension (BUT) tests evidenced that the performance for stamping conditions of the PIL with the longest anion carbon chain was similar to that of the commercial lubricant. Since, both formed a uniform tribofilm, developed the same lubrication regime and the drawing forces values were close and constant. Hence, the ionic liquid obtained with 2HEA and pentanoic acid (2HEAPe) is as suitable as the commercial lubricant for metal forming processes

Diagnostic guidelines for the histological particle algorithm in the periprosthetic neo-synovial tissue

Background The identification of implant wear particles and non-implant related particles and the characterization of the inflammatory responses in the periprosthetic neo-synovial membrane, bone, and the synovial-like interface membrane (SLIM) play an important role for the evaluation of clinical outcome, correlation with radiological and implant retrieval studies, and understanding of the biological pathways contributing to implant failures in joint arthroplasty. The purpose of this study is to present a comprehensive histological particle algorithm (HPA) as a practical guide to particle identification at routine light microscopy examination. Methods The cases used for particle analysis were selected retrospectively from the archives of two institutions and were representative of the implant wear and non-implant related particle spectrum. All particle categories were described according to their size, shape, colour and properties observed at light microscopy, under polarized light, and after histochemical stains when necessary. A unified range of particle size, defined as a measure of length only, is proposed for the wear particles with five classes for polyethylene (PE) particles and four classes for conventional and corrosion metallic particles and ceramic particles. Results All implant wear and non-implant related particles were described and illustrated in detail by category. A particle scoring system for the periprosthetic tissue/SLIM is proposed as follows: 1) Wear particle identification at light microscopy with a two-step analysis at low (× 25, × 40, and × 100) and high magnification (× 200 and × 400); 2) Identification of the predominant wear particle type with size determination; 3) The presence of non-implant related endogenous and/or foreign particles. A guide for a comprehensive pathology report is also provided with sections for macroscopic and microscopic description, and diagnosis. Conclusions The HPA should be considered a standard for the histological analysis of periprosthetic neo-synovial membrane, bone, and SLIM. It provides a basic, standardized tool for the identification of implant wear and non-implant related particles at routine light microscopy examination and aims at reducing intra-observer and inter-observer variability to provide a common platform for multicentric implant retrieval/radiological/histological studies and valuable data for the risk assessment of implant performance for regional and national implant registries and government agencies