Blob distortion by radio-frequency induced sheared flow

Blob transport properties in the plasma edge in the presence and absence of radio-frequency (RF) convective cells are compared. For the first time, the interactions between RF convective cells and intermittent plasma blobs in the scrape-off layer (SOL) are observed with gas puff imaging in the ASDEX Upgrade tokamak. It is found that the RF convective cells induce a sheared flow in the far SOL, which is able to stretch, distort and even split the blobs poloidally. The observed phenomena indicate that an externally generated sheared flow in the SOL can be considered as a method to modify blob transport in a favorable way

Scrape Off Layer (SOL) transport and filamentary characteristics in high density tokamak regimes

A detailed cross-device investigation on the role of filamentary dynamics in high density regimes has been performed within the EUROfusion framework comparing ASDEX Upgrade (AUG) and TCV tokamaks. Both devices have run density ramp experiments at different levels of plasma current, keeping toroidal field or q95 constant in order to disentangle the role of parallel connection length and the current. During the scan at constant toroidal field, in both devices SOL profiles tend to develop a clear Scrape Off Layer (SOL) density shoulder at lower edge density whenever current is reduced. The different current behavior is substantially reconciled in terms of edge density normalized to Greenwald fraction. During the scan at constant q95 AUG exhibits a similar behaviour whereas in TCV no signature of upstream profile modification has been observed at lower level of currents. The latter behaviour has been ascribed to the lack of target density roll-over. The relation between upstream density profile modification and detachment condition has been investigated. For both devices the relation between blob-size and SOL density e-folding length is found independent of the plasma current, with a clear increase of blob-size with edge density normalized to Greenwald fraction observed. ASDEX Upgrade has also explored the filamentary behaviour in H-Mode. The experiments on AUG focused on the role of neutrals, performing discharges with and without the cryogenic pumps, highlighting how large neutral pressure not only in the divertor but at the midplane is needed in order to develop a H-Mode SOL profile shoulder in AUG

Progress from ASDEX Upgrade experiments in preparing the physics basis of ITER operation and DEMO scenario development

An overview of recent results obtained at the tokamak ASDEX Upgrade (AUG) is given. A work flow for predictive profile modelling of AUG discharges was established which is able to reproduce experimental H-mode plasma profiles based on engineering parameters only. In the plasma center, theoretical predictions on plasma current redistribution by a dynamo effect were confirmed experimentally. For core transport, the stabilizing effect of fast ion distributions on turbulent transport is shown to be important to explain the core isotope effect and improves the description of hollow low-Z impurity profiles. The L-H power threshold of hydrogen plasmas is not affected by small helium admixtures and it increases continuously from the deuterium to the hydrogen level when the hydrogen concentration is raised from 0 to 100%. One focus of recent campaigns was the search for a fusion relevant integrated plasma scenario without large edge localised modes (ELMs). Results from six different ELM-free confinement regimes are compared with respect to reactor relevance: ELM suppression by magnetic perturbation coils could be attributed to toroidally asymmetric turbulent fluctuations in the vicinity of the separatrix. Stable improved confinement mode plasma phases with a detached inner divertor were obtained using a feedback control of the plasma β. The enhanced D α H-mode regime was extended to higher heating power by feedback controlled radiative cooling with argon. The quasi-coherent exhaust regime was developed into an integrated scenario at high heating power and energy confinement, with a detached divertor and without large ELMs. Small ELMs close to the separatrix lead to peeling-ballooning stability and quasi continuous power exhaust. Helium beam density fluctuation measurements confirm that transport close to the separatrix is important to achieve the different ELM-free regimes. Based on separatrix plasma parameters and interchange-drift-Alfvén turbulence, an analytic model was derived that reproduces the experimentally found important operational boundaries of the density limit and between L- and H-mode confinement. Feedback control for the X-point radiator (XPR) position was established as an important element for divertor detachment control. Stable and detached ELM-free phases with H-mode confinement quality were obtained when the XPR was moved 10 cm above the X-point. Investigations of the plasma in the future flexible snow-flake divertor of AUG by means of first SOLPS-ITER simulations with drifts activated predict beneficial detachment properties and the activation of an additional strike point by the drifts

Observation of magnetic islands in tokamak plasmas during the suppression of edge-localized modes

In tokamaks, a leading platform for fusion energy, periodic filamentary plasma eruptions known as edge-localized modes occur in plasmas with high-energy confinement and steep pressure profiles at the plasma edge. These edge-localized modes could damage the tokamak wall but can be suppressed using small three-dimensional magnetic perturbations. Here we demonstrate that these magnetic perturbations can change the magnetic topology just inside the steep gradient region of the plasma edge. We identify signatures of a magnetic island, and their observation is linked to the suppression of edge-localized modes. We compare high-resolution measurements of perturbed magnetic surfaces with predictions from ideal magnetohydrodynamic theory where the magnetic topology is preserved. Although ideal magnetohydrodynamics adequately describes the measurements in plasmas exhibiting edge-localized modes, it proves insufficient for plasmas where these modes are suppressed. Nonlinear resistive magnetohydrodynamic modelling supports this observation. Our study experimentally confirms the predicted role of magnetic islands in inhibiting the occurrence of edge-localized modes. This will be beneficial for physics-based predictions in future fusion devices to control these modes

Barley starch

This thesis examined barley amylopectin structure and looked for correlations between the structure and physical properties of starch. The structure of amylopectin and gelatinisation and retrogradation of starch were studied in 10 different barley cultivars/breeding lines with differing genetic background. Amylopectin is built up of thousands of chains of glucose monomers, organised into clusters. The detailed fine structure of amylopectin was studied by isolating clusters of amylopectin and their building blocks, which are the tightly branched units building up the clusters. Barley cultivars/breeding lines possessing the amo1 mutation had fewer long chains of DP≥38 in amylopectin and more large building blocks. The structure of building blocks was rather conserved between the different barley cultivars/breeding lines studied and was categorized into different size groups. These different building blocks were shown to be randomly distributed in the amylopectin molecule. The C-chains in amylopectin can be of any length and are a category of chains different from the B-chains. The backbone in amylopectin consists of a special type of B-chains which, when cleaved by α-amylase, become chains of a similar type to C-chains. Gelatinisation and retrogradation (recrystallisation of gelatinised starch) of barley starch was studied by differential scanning calorimetry. The amo1 mutation resulted in a broader gelatinisation temperature range and a higher enthalpy of retrogradation. Other structural features were also found to influence the physical properties of starch. Small clusters and denser structure of the building blocks resulted in higher gelatinisation temperature. Fast retrogradation was observed in barley which had amylopectin with shorter chains and many large building blocks consisting of many chains. Amylopectin structure was also studied in developing barley kernels. Three barley cultivars/breeding lines were grown in a phytotron and kernels were harvested at 9, 12 and 24 days after flowering. The results showed that amylopectin synthesized at later stages of development had a more tightly branched structure. Expression of the enzymes involved in starch biosynthesis is also known to change during endosperm development