Electricity Demand Profile of Australian Low Energy Houses

AbstractThe paper demonstrates the profiles of electricity consumption in the low energy housing sector using various time frames, and provides a solid basis for energy estimation by analysing actual 12 month electricity data from 60 comprehensively monitored low energy houses in Australia's leading sustainable green village (Lochiel Park), located in South Australia. The results highlight that although considerable electricity reduction is achieved in low energy houses, the outdoor ambient air temperature is still a highly influential factor that determines the total and peak demand in these houses. It also suggests that energy estimation should focus on residents’ basic life style and appliance usage behaviour. The results presented here can be used to refine end-use electricity demand modelling for low energy houses in South Australia, and can hence assist the design of electrical infrastructure requirements in new low energy housing developments

A framework for adaptation of Australian households to heat waves

AbstractClimate change is leading to an increased frequency and severity of heat waves. Spells of several consecutive days of unusually high temperatures have led to increased mortality rates for the more vulnerable in the community. The problem is compounded by the escalating energy costs and increasing peak electrical demand as people become more reliant on air conditioning. Domestic air conditioning is the primary determinant of peak power demand which has been a major driver of higher electricity costs. This report presents the findings of multidisciplinary research which develops a national framework to evaluate the potential impacts of heat waves. It presents a technical, social and economic approach to adapt Australian residential buildings to ameliorate the impact of heat waves in the community and reduce the risk of its adverse outcomes.Through the development of a methodology for estimating the impact of global warming on key weather parameters in 2030 and 2050, it is possible to re-evaluate the size and anticipated energy consumption of air conditioners in future years for various climate zones in Australia.  Over the coming decades it is likely that mainland Australia will require more cooling than heating.  While in some parts the total electricity usage for heating and cooling may remain unchanged, there is an overall significant increase in peak electricity demand, likely to further drive electricity prices.  Through monitoring groups of households in South Australia, New South Wales and Queensland, the impact of heat waves on both thermal comfort sensation and energy consumption for air conditioning has been evaluated. The results show that households are likely to be able to tolerate slightly increased temperature levels indoors during periods of high outside temperatures. The research identified that household electricity costs are likely to rise above what is currently projected due to the impact of climate change. Through a number of regulatory changes to both household design and air conditioners, this impact can be minimised.  A number of proposed retrofit and design measures are provided, which can readily reduce electricity usage for cooling at minimal cost to the household.  Using a number of social research instruments, it is evident that households are willing to change behaviour rather than to spend money. Those on lower income and elderly individuals are the least able to afford the use of air conditioning and should be a priority for interventions and assistance. Increasing community awareness of cost-effective strategies to manage comfort and health during heat waves is a high priority recommended action.Overall, the research showed that a combined approach including behaviour change, dwelling modification and improved air conditioner selection can readily adapt Australian households to the impact of heat waves, reducing the risk of heat related deaths and household energy costs.Climate change is leading to an increased frequency and severity of heat waves. Spells of several consecutive days of unusually high temperatures have led to increased mortality rates for the more vulnerable in the community. The problem is compounded by the escalating energy costs and increasing peak electrical demand as people become more reliant on air conditioning. Domestic air conditioning is the primary determinant of peak power demand which has been a major driver of higher electricity costs. This report presents the findings of multidisciplinary research which develops a national framework to evaluate the potential impacts of heat waves. It presents a technical, social and economic approach to adapt Australian residential buildings to ameliorate the impact of heat waves in the community and reduce the risk of its adverse outcomes.Through the development of a methodology for estimating the impact of global warming on key weather parameters in 2030 and 2050, it is possible to re-evaluate the size and anticipated energy consumption of air conditioners in future years for various climate zones in Australia.  Over the coming decades it is likely that mainland Australia will require more cooling than heating.  While in some parts the total electricity usage for heating and cooling may remain unchanged, there is an overall significant increase in peak electricity demand, likely to further drive electricity prices.  Through monitoring groups of households in South Australia, New South Wales and Queensland, the impact of heat waves on both thermal comfort sensation and energy consumption for air conditioning has been evaluated. The results show that households are likely to be able to tolerate slightly increased temperature levels indoors during periods of high outside temperatures. The research identified that household electricity costs are likely to rise above what is currently projected due to the impact of climate change. Through a number of regulatory changes to both household design and air conditioners, this impact can be minimised.  A number of proposed retrofit and design measures are provided, which can readily reduce electricity usage for cooling at minimal cost to the household.  Using a number of social research instruments, it is evident that households are willing to change behaviour rather than to spend money. Those on lower income and elderly individuals are the least able to afford the use of air conditioning and should be a priority for interventions and assistance. Increasing community awareness of cost-effective strategies to manage comfort and health during heat waves is a high priority recommended action.Overall, the research showed that a combined approach including behaviour change, dwelling modification and improved air conditioner selection can readily adapt Australian households to the impact of heat waves, reducing the risk of heat related deaths and household energy costs.Please cite this report as:Saman, W, Boland, J, Pullen, S, de Dear, R, Soebarto, V, Miller, W, Pocock, B, Belusko, M, Bruno, F, Whaley, D, Pockett, J, Bennetts, H, Ridley, B, Palmer, J, Zuo, J, Ma, T, Chileshe, N, Skinner, N, Chapman, J, Vujinovic, N, Walsh, M, Candido, C, Deuble, M 2013 A framework for adaptation of Australian households to heat waves, National Climate Change Adaptation Research Facility, Gold Coast, pp. 242.&nbsp

A eutectic salt high temperature phase change material: Thermal stability and corrosion of SS316 with respect to thermal cycling

Thermal energy storage (TES) is a critical component in a concentrated solar power (CSP) plant since it is able to provide dispatchability and increase the capacity factor of the plant. Recently the Brayton power cycle using supercritical carbon dioxide (s-CO2) has attracted considerable attention as it allows a higher thermal to electric power conversion efficiency compared to the conventional Rankine cycle using subcritical steam. However, no commercial TES has yet been developed for integration with a s-CO2 based plant. One reason is the lack of a suitable storage material. This work explores the use of a eutectic NaCl-Na2CO3 salt as a reliable high temperature phase change material (PCM). The PCM has been thermally cycled up to 1000 times. Its thermophysical properties have been measured before and after it has been subjected to the thermal cycling and its corrosion behavior has been investigated. This eutectic salt shows good thermal stability without degradation after cycling 1000 times between 600 and 650 °C. The corrosion rate on stainless steel 316 (SS316) increases linearly up to 350 cycles, and thereafter it stabilizes at 70 mg/cm2

Novel geopolymer for use as a sensible storage option in high temperature thermal energy storage systems

In the current study a novel geopolymer created from waste materials (namely fly ash and black slag) has been characterised as a potential high temperature thermal energy storage material option. Several geopolymer samples have been fabricated and characterised by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Additionally, the density and heat capacity have been determined. Lastly, the cost of the material and packed bed system was estimated showing that the geopolymer-based systems are potentially 35% cheaper than the traditional 2-tank molten salt systems.This research was performed as part of the Australian Solar Thermal Research Institute (ASTRI), a project supported by the Australian Government, through the Australian Renewable Energy Agency (ARENA). The work was partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123). GREA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. This project has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement Nº PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). Aran Solé would like to thank Ministerio de Economía y Competitividad de España for Grant Juan de la Cierva, FJCI-2015-25741. The authors would also like to acknowldege the Diopma group from the University of Barcelona thanks the funding by the Spanish Government (RTI2018-093849-B-C32), and the Catalan Government for the quality accreditation (2017 SGR 118)

Novel Geopolymer for Use as a Sensible Storage Option in High Temperature Thermal Energy Storage Systems

In the current study a novel geopolymer created from waste materials (namely fly ash and black slag) has been characterised as a potential high temperature thermal energy storage material option. Several geopolymer samples have been fabricated and characterised by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Additionally, the density and heat capacity have been determined. Lastly, the cost of the material and packed bed system was estimated showing that the geopolymer-based systems are potentially 35% cheaper than the traditional 2-tank molten salt systems

Sustainable energy education: addressing the needs of students and industry in Australia

A survey has been carried out of graduates and employers working in the sustainable energy (SE) industry in Australia. The aims were to identify the key areas of content to be included in University level SE training and the type of degree structures that are most appropriate for SE professionals. Attention was also directed to the mode of instruction (online, blended or face-to-face) and the role of work-integrated learning (WIL). This paper presents the results of the survey, which provide guidance to Universities seeking to develop new, or revise existing, SE education offerings. The results of the survey clearly indicate that responding students and employers prefer a generalist degree in engineering, with a stream in sustainable energy as the initial qualification for professionals in this field. Specialist degrees at postgraduate level were also considered appropriate for continuing professional education (CPE). Both graduates and employers agreed on key areas to be included in the SE courses. These key areas are generic skills (research methods, team work, report writing), generation technologies (especially PV, wind and biomass), and enablers (such as economics, policy and project management). The graduates, many of whom came from overseas countries, generally agreed about the course content and its relevance to employment in their countries. Face-to-face or blended learning was preferred by both groups as the mode of instruction for the first degree. Online learning was considered a valuable adjunct in the undergraduate course and more suitable for CPE in postgraduate courses. WIL and more practical work were considered important, especially in the first degree. There was some disagreement about the appropriate length of work placements, with graduates preferring 6–8 weeks and employers 10–12 weeks. This work should provide a basis for further course development and curriculum reform for sustainable energy education

Reducing the environmental impact of surgery on a global scale: systematic review and co-prioritization with healthcare workers in 132 countries

Abstract Background Healthcare cannot achieve net-zero carbon without addressing operating theatres. The aim of this study was to prioritize feasible interventions to reduce the environmental impact of operating theatres. Methods This study adopted a four-phase Delphi consensus co-prioritization methodology. In phase 1, a systematic review of published interventions and global consultation of perioperative healthcare professionals were used to longlist interventions. In phase 2, iterative thematic analysis consolidated comparable interventions into a shortlist. In phase 3, the shortlist was co-prioritized based on patient and clinician views on acceptability, feasibility, and safety. In phase 4, ranked lists of interventions were presented by their relevance to high-income countries and low–middle-income countries. Results In phase 1, 43 interventions were identified, which had low uptake in practice according to 3042 professionals globally. In phase 2, a shortlist of 15 intervention domains was generated. In phase 3, interventions were deemed acceptable for more than 90 per cent of patients except for reducing general anaesthesia (84 per cent) and re-sterilization of ‘single-use’ consumables (86 per cent). In phase 4, the top three shortlisted interventions for high-income countries were: introducing recycling; reducing use of anaesthetic gases; and appropriate clinical waste processing. In phase 4, the top three shortlisted interventions for low–middle-income countries were: introducing reusable surgical devices; reducing use of consumables; and reducing the use of general anaesthesia. Conclusion This is a step toward environmentally sustainable operating environments with actionable interventions applicable to both high– and low–middle–income countries

Thermal performance analysis of a phase change thermal storage unit for space heating

This paper presents the results of a comprehensive numerical study on the thermal performance of an air based phase change thermal storage unit (TSU) for space heating. The unit is designed for integration into space heating and cooling systems. The unit consists of a number of one dimensional phase change material (PCM) slabs contained in a rectangular duct where air passes between the slabs. The numerical analysis was based on an experimentally validated model. A parametric study has been carried out including the study on the effects of charge and discharge temperature differences, air mass flow rate, slab thicknesses, air gaps and slab dimensions on the air outlet temperatures and heat transfer rates of the thermal storage unit. The paper introduces and discusses quantities called charge and discharge temperature differences which play an important role in the melting and freezing processes.