Catalytic microwave pyrolysis of waste engine oil using metallic pyrolysis char

Microwave pyrolysis was performed on waste engine oil pre-mixed with different amounts of metallic-char catalyst produced previously from a similar microwave pyrolysis process. The metallic-char catalyst was first prepared by pretreatment with calcination followed by analyses to determine its various properties. The heating characteristics of the mixture of waste oil and metallic-char during the pyrolysis were investigated, and the catalytic influence of the metallic-char on the yield and characteristics of the pyrolysis products are discussed with emphasis on the composition of oil and gaseous products. The metallic-char, detected to have a porous structure and high surface area (124 m2/g), showed high thermal stability in a N2 atmosphere and it was also found to have phases of metals and metal oxides attached or adsorbed onto the char, representing a potentially suitable catalyst to be used in pyrolysis cracking process. The metallic-char initially acted as an adsorptive-support to adsorb metals, metal oxides and waste oil. Then, the char became a microwave absorbent that absorbed microwave energy and heated up to a high temperature in a short time and it was found to generate arcing and sparks during microwave pyrolysis of the waste oil, resulting in the formation of hot spots (high temperature sites with temperature up to 650 °C) within the reactor under the influence of microwave heating. The presence of this high temperature metallic-char, the amounts of which are likely to increase when increasing amounts of metallic-char were added to the waste oil (5, 10, and 20 wt% of the amount of waste oil added to the reactor), had provided a reducing chemical environment in which the metallic-char acted as an intermediate reductant to reduce the adsorbed metals or metal oxides into metallic states, which then functioned as a catalyst to provide more reaction sites that enhanced the cracking and heterogeneous reactions that occurred during the pyrolysis to convert the waste oil to produce higher yields of light hydrocarbons, H2 and CO gases in the pyrolysis products, recording a yield of up to 74 wt% of light C5–C10 hydrocarbons and 42 vol% of H2 and CO gases. The catalytic microwave pyrolysis produced 65–85 wt% yield of pyrolysis-oil containing C5–C20 hydrocarbons that can potentially be upgraded to produce transport-grade fuels. In addition, the recovered pyrolysis-gases (up to 33 wt%) were dominated by aliphatic hydrocarbons (up to 78 vol% of C1–C6 hydrocarbons) and significant amounts of valuable syngas (up to 42 vol% of H2 and CO in total) with low heating values (LHV) ranging from 4.7 to 5.5 MJ/m3, indicating that the pyrolysis-gases could also be used as a gaseous fuel or upgraded to produce more hydrogen as a second-generation fuel. The results indicate that the metallic-char shows advantages for use as a catalyst in microwave pyrolysis treatment of problematic waste oils. [Graphical abstract - see article]The authors acknowledges the financial support by the Ministry of Science, Technology, and Innovation Malaysia (MOSTI), Ministry of Higher Education Malaysia (MOHE), and University Malaysia Terengganu for the conduct of the research under the E-Science fund (UMT/RMC/SF/13/52072(5), Vot No: 52072), the Fundamental Research Grant Scheme (Project No: FRGS/1/2013/TK05/UMT/02/2, Vot No: 59296), and the Research Acculturation Grant Scheme (Project No: RAGS/2012/UMT/TK07/3, Vot No: 57085).This is the author accepted manuscript. The final version is available from [publisher] via http://dx.doi.org/10.1016/j.apcatb.2015.04.01

Recovery of diesel-like fuel from waste palm oil by pyrolysis using a microwave heated bed of activated carbon

Microwave pyrolysis using a well-mixed bed of activated carbon as both the microwave absorber and reaction bed was investigated for its potential to recover useful products from waste palm cooking oil – a cooking oil widely used in Asia. The carbon bed provided rapid heating (∼18 °C/min) and a localized reaction hot zone that thermally promoted extensive pyrolysis cracking of the waste oil at 450 °C, leading to increased production of a biofuel product in a process taking less than 25 min. It also created a reducing reaction environment that prevented the formation of undesirable oxidized compounds in the biofuel. The pyrolysis produced a biofuel product that is low in oxygen, free of sulphur, carboxylic acid and triglycerides, and which also contains light C$_{10}$-C$_{15}$ hydrocarbons and a high calorific value nearly comparable to diesel fuel, thus showing great potential to be used as fuel. This pyrolysis approach offers an attractive alternative to transesterification that avoids the use of solvents and catalysts, and the need to remove free fatty acids and glycerol from the hydrocarbon product. The pyrolysis apparatus operated with an electrical power input of 1.12 kW was capable of producing a biofuel with an energy content equivalent to about 3 kW, showing a positive energy ratio of 2.7 and ≥73% recovery of the energy input to the system. The results show that the pyrolysis approach has huge potential as a technically and energetically viable means for the recovery of biofuels from the waste oil.The authors acknowledge the financial support by the Ministry of Science, Technology and Innovation and the Ministry of Higher Education Malaysia for the conduct of the research under the E-Science fund (UMT/RMC/SF/13/52072(5), Vot 52072) and the FRGS grant (FRGS/1/2016/TK07/UMT/02/3, Vot 59434).This is the author accepted manuscript. The final version is available from Elsevier via https://doi.org/10.1016/j.energy.2016.09.07

Monitoring Partially Synchronous Distributed Systems using SMT Solvers

In this paper, we discuss the feasibility of monitoring partially synchronous distributed systems to detect latent bugs, i.e., errors caused by concurrency and race conditions among concurrent processes. We present a monitoring framework where we model both system constraints and latent bugs as Satisfiability Modulo Theories (SMT) formulas, and we detect the presence of latent bugs using an SMT solver. We demonstrate the feasibility of our framework using both synthetic applications where latent bugs occur at any time with random probability and an application involving exclusive access to a shared resource with a subtle timing bug. We illustrate how the time required for verification is affected by parameters such as communication frequency, latency, and clock skew. Our results show that our framework can be used for real-life applications, and because our framework uses SMT solvers, the range of appropriate applications will increase as these solvers become more efficient over time.Comment: Technical Report corresponding to the paper accepted at Runtime Verification (RV) 201

Progress in waste oil to sustainable energy, with emphasis on pyrolysis techniques

This paper begins with a review on the current techniques used for the treatment and recovery of waste oil, which is then followed by an extensive review of the recent achievements in the sustainable development and utilization of pyrolysis techniques in energy recovery from waste oils. The advantages and limitations shown by the use of pyrolysis technique and other current techniques were discussed along with the future research that can be performed on the pyrolysis of waste oil. It was revealed that the current techniques (transesterification, hydrotreating, gasification, solvent extraction, and membrane technology) are yet to be sustainable or completely feasible for waste oil treatment and recovery. It was established that pyrolysis techniques offer a number of advantages over other existing techniques in recovering both the energetic and chemical value of waste oil by generating potentially useful pyrolysis products suitable for future reuse. In particular, microwave pyrolysis shows a distinct advantage in providing a rapid and energy-efficient heating compared to conventional pyrolysis techniques, and thus facilitating increased production rates. It was found that microwave pyrolysis of waste oil showed good performance with respect to product yield, reaction time, energy consumption, and product quality, and thus showing exceptional promise as a sustainable means for energy recovery from waste oils. Nevertheless, it was revealed that some important characteristics of the pyrolysis process have yet to be fully investigated. It was thus concluded that more studies are needed to extend existing understanding in the optimal reaction and process parameters in order to develop the pyrolysis technology to be a sustainable and commercially viable route for energy recovery from problematic waste oils.The authors acknowledges the financial support by Ministry of Science, Technology, and Innovation Malaysia (MOSTI), Ministry of Higher Education Malaysia (MOHE), and Universiti Malaysia Terengganu for the conduct of the research under the E-Science fund (UMT/RMC/SF/13/52072(5), Vot no.: 52072), the Fundamental Research Grant Scheme (Project no.: FRGS/1/2013/TK05/UMT/02/2, Vot no.: 59296), and the Research Acculturation Grant Scheme (Project no.: RAGS/2012/UMT/TK07/3, Vot no.: 57085).This is the author accepted manuscript. The final version is available from Elsevier via http://dx.doi.org/10.1016/j.rser.2015.09.00

Pyrolysis using microwave absorbents as reaction bed: An improved approach to transform used frying oil into biofuel product with desirable properties

Used frying oil (UFO), a waste produced in large volume each year worldwide, represents a potential resource for biofuel production rather than a disposal problem for modern society. Pyrolysis technique using microwave heating offers a promising approach for the conversion of UFO into biofuel products with improved properties. In this study, pyrolysis of UFO was performed by contacting with a bed of microwave absorbents heated by microwave radiation. The pyrolysis approach was examined using different materials as the reaction bed, comprising particulate carbon, activated carbon and mesoporous aluminosilicate (MCM-41). The use of particulate and activated carbon as the reaction bed provided a fast heating rate and extensive cracking capacity to pyrolyze the used oil, thus showing favorable features that could lead to short process time and less energy usage. This resulted in a production of a high yield of a biofuel product (up to 73 wt%) in a process taking less than 35 min. The biofuel showed a composition dominated by light C$_{5}$-C$_{20}$ aliphatic hydrocarbons with low amounts of oxygenated compounds (≤11%). In particular, the oil product obtained from activated carbon bed showed a low nitrogen content and was free of carboxylic acid and sulphur. The absence of carboxylic acids with low amounts of oxygenated compounds could reduce the formation of oxygenated by-products that could generate undesirable acidic tar or potentially hazardous sludge in the biofuel during storage. Combined with the detection of a high calorific value (46 MJ/kg) nearly comparable to diesel fuel, the biofuel shows great promise to be upgraded for use as a ‘cleaner’ fuel source with potentially reduced oxygenated by-products plus low or zero emissions of NO$_{x}$ and SO$_{x}$ during the use of the fuel in combustion process. This study also revealed that the use of activated carbon bed results in the highest energy recovery (88–90%) from the used frying oil. Our results demonstrated that the use of a microwave-heated reaction bed of activated carbon shows great potential as an improved and sustainable pyrolysis approach that is energy-efficient and timesaving for the recycling of used frying oil into a biofuel product with desirable properties. This pyrolysis approach provides an alternative to transesterification that avoids the use of solvents and catalysts, and thus could be developed further as a promising route to recycle various types of waste and biomass materials

Microwave-assisted pyrolysis with chemical activation, an innovative method to convert orange peel into activated carbon with improved properties as dye adsorbent

Microwave-assisted pyrolysis with chemical activation was developed and optimized to transform orange peel into activated carbon (AC) desirable for use as a dye adsorbent. The orange peel was first carbonized via microwave-assisted pyrolysis to produce a biochar, which was then activated and converted into AC via chemical impregnation coupled with microwave-assisted pyrolysis. The process parameters involved was optimized to maximize the yield of AC and its adsorption efficiency on malachite green dye using response surface methodology adopting central composite design. The use of microwave-assisted pyrolysis provided a fast heating rate and short process time in converting orange peel into AC, recording a heating rate of up to 112 °C/min in a process taking about 25 min, representing a method that is potentially faster and more energy efficient compared to that shown by the method commonly performed using conventional heating source (≥1 h). The results showed that AC with the highest yield (87 wt% of biochar) and optimal adsorption efficiency (28.5 mg of dye/g of AC) can be obtained by performing chemical impregnation at an impregnation ratio of 1:1 coupled with microwave-assisted pyrolysis under microwave irradiation (heating) for 5 min using 550 W of microwave power. The addition of chemical activation with alkali metal hydroxides resulted in the production of AC with improved properties. The AC showed a highly porous structure containing high content of fixed carbon (83 wt%) and high BET surface area (1350 m 2 /g). The adsorption–desorption isotherm showed a combination of Type I and Type II isotherms, which indicates the presence of microporous-mesoporous structure, thus exhibiting a characteristic of improved pores accessibility and high adsorption capacity. Combined with the detection of low ash (3.2 wt%) and moisture content (5 wt%), the AC shows great promise as a high-grade dye adsorbent with high adsorption capacity and potentially increased durability since a low moisture content could increase the rate of adsorption of dye contaminants and a high ash content could promote undesirable catalytic reactions and reduce the adsorption capacity and reactivation efficiency of AC. The recovery of AC with improved properties and the desirable process features (fast heating rate, short process time) suggest the great potential of this method as an alternative for the treatment and recovery of fruit peel

Colored Motifs Reveal Computational Building Blocks in the C. elegans Brain

Background: Complex networks can often be decomposed into less complex sub-networks whose structures can give hints about the functional organization of the network as a whole. However, these structural motifs can only tell one part of the functional story because in this analysis each node and edge is treated on an equal footing. In real networks, two motifs that are topologically identical but whose nodes perform very different functions will play very different roles in the network. Methodology/Principal Findings: Here, we combine structural information derived from the topology of the neuronal network of the nematode C. elegans with information about the biological function of these nodes, thus coloring nodes by function. We discover that particular colorations of motifs are significantly more abundant in the worm brain than expected by chance, and have particular computational functions that emphasize the feed-forward structure of information processing in the network, while evading feedback loops. Interneurons are strongly over-represented among the common motifs, supporting the notion that these motifs process and transduce the information from the sensor neurons towards the muscles. Some of the most common motifs identified in the search for significant colored motifs play a crucial role in the system of neurons controlling the worm's locomotion. Conclusions/Significance: The analysis of complex networks in terms of colored motifs combines two independent data sets to generate insight about these networks that cannot be obtained with either data set alone. The method is general and should allow a decomposition of any complex networks into its functional (rather than topological) motifs as long as both wiring and functional information is available

A dimensioning and tolerancing methodology for concurrent engineering applications I: problem representation

This paper is the first of two which present a methodology for determining the dimensional specifications of all the component parts and sub-assemblies of a product according to their dimensional requirements. To achieve this goal, two major steps are followed, each of which is described in a paper. In the first paper, all relationships necessary for finding the values of dimensions and tolerances are represented in a matrix form, known as a Dimensional Requirements/Dimensions (DR/D) matrix. In the second paper, the values of individual dimensions and tolerances are determined by applying a comprehensive solution strategy to satisfy all the relationships represented in the DR/D matrix. The methodology is interactive and suitable for use in a concurrent engineering (CE) environment. The graphical tool presented in this paper will assist a CE team in visualizing the overall D&T problem and foreseeing the ramifications of decisions regarding the selection of dimensions and tolerances. This will assist the CE team to systematically determine all the controllable variables, such as dimensions, tolerances, and manufacturing processes

DNA Barcoding in the Cycadales: Testing the Potential of Proposed Barcoding Markers for Species Identification of Cycads

Barcodes are short segments of DNA that can be used to uniquely identify an unknown specimen to species, particularly when diagnostic morphological features are absent. These sequences could offer a new forensic tool in plant and animal conservation—especially for endangered species such as members of the Cycadales. Ideally, barcodes could be used to positively identify illegally obtained material even in cases where diagnostic features have been purposefully removed or to release confiscated organisms into the proper breeding population. In order to be useful, a DNA barcode sequence must not only easily PCR amplify with universal or near-universal reaction conditions and primers, but also contain enough variation to generate unique identifiers at either the species or population levels. Chloroplast regions suggested by the Plant Working Group of the Consortium for the Barcode of Life (CBoL), and two alternatives, the chloroplast psbA-trnH intergenic spacer and the nuclear ribosomal internal transcribed spacer (nrITS), were tested for their utility in generating unique identifiers for members of the Cycadales. Ease of amplification and sequence generation with universal primers and reaction conditions was determined for each of the seven proposed markers. While none of the proposed markers provided unique identifiers for all species tested, nrITS showed the most promise in terms of variability, although sequencing difficulties remain a drawback. We suggest a workflow for DNA barcoding, including database generation and management, which will ultimately be necessary if we are to succeed in establishing a universal DNA barcode for plants

The influence of elastic orthotic belt on sagittal profile in adolescent idiopathic thoracic scoliosis: a comparative radiographic study with Milwaukee brace

<p>Abstract</p> <p>Background</p> <p>The effectiveness of bracing on preventing curve progression in coronal plane for mild and moderate adolescent idiopathic scoliosis (AIS) patients has been confirmed by previous radiographic researches. However, a hypokyphotic effect on the sagittal plane has been reported by a few studies. A relatively increasing number of AIS patients were noticed to wear a new kind of elastic orthotic belt for the treatments of scoliosis without doctors' instructions. We postulate the correcting mechanism of this new appliance may cause flattening of the spine. To our knowledge, no study has investigated the effects of this new orthosis on the sagittal profile of AIS patients. The aim of this study was to evaluate and compare the effects of elastic orthotic belt and Milwaukee brace on the sagittal alignment in AIS patients.</p> <p>Methods</p> <p>Twenty-eight female AIS patients with mild or moderate thoracic curves were included in this study. Standing full-length lateral radiographs were obtained in three conditions: natural standing posture without any treatment, with elastic orthotic belt and with Milwaukee brace. Thoracic kyphosis (TK), lumber lordosis (LL) and pelvic incidence (PI) were measured and compared between the above three conditions.</p> <p>Results</p> <p>Both elastic orthotic belt and Milwaukee brace can lead to significant decrease of TK, however, the decrease of TK after wearing elastic orthotic belt is significantly larger than that after wearing Milwaukee brace. Compared with no treatment, LL was found to be significantly smaller after wearing Milwaukee brace, however, such significant decrease was not noted after wearing elastic orthotic belt. No significant changes were observed for the PI between 3 conditions.</p> <p>Conclusions</p> <p>The elastic orthotic belt could lead to more severe thoracic hypokyphosis when compared with Milwaukee brace. This belt may not be a suitable conservative method for the treatment of mild and moderate AIS patients.</p