Initiation of corona pulses

http://www.ester.ee/record=b1065966~S1*es

Ex Situ LIBS Analysis of WEST Divertor Wall Tiles after C3 Campaign

Fuel retention monitoring in tokamak walls requires the development of remote composition analysis methods such as laser-induced breakdown spectroscopy (LIBS). The present study investigates the feasibility of the LIBS method to analyse the composition and fuel retention in three samples from WEST divertor erosion marker tiles after the experimental campaign C3. The investigated samples originated from tile regions outside of strong erosion and deposition regions, where the variation of thin deposit layers is relatively small and facilitates cross-comparison between different analysis methods. The depth profiles of main constituents W, Mo and C were consistent with depth profiles determined by other composition analysis methods, such as glow-discharge optical emission spectroscopy (GDOES) and secondary ion mass spectrometry (SIMS). The average LIBS depth resolution determined from depth profiles was 100 nm/shot. The averaging of the spectra collected from multiple spots of a same sample allowed us to improve the signal-to-noise ratio, investigate the presence of fuel D and trace impurities such as O and B. In the investigated tile regions with negligible erosion and deposition, these impurities were clearly detectable during the first laser shot, while the signal decreased to noise level after a few subsequent laser shots at the same spot. LIBS investigation of samples originating from the deposition regions of tiles may further clarify LIBS’ ability to investigate trace impurities

Micro-NRA and micro-3HIXE with He-3 microbeam on samples exposed in ASDEX Upgrade and Pilot-PSI machines

Micro nuclear reaction analysis (micro-NRA) exploiting the nuclear reaction D(3He,p)4He was used for post-mortem analyses of special marker samples, exposed to deuterium plasma inside ASDEX Upgrade (AUG) tokamak and to the deuterium plasma jet in the Pilot-PSI linear plasma gun. Lateral concentration profiles of deuterium and erosion/deposition profiles of the marker materials were obtained by a combination of micro-NRA and particle induced X-ray emission by 3He beam (3HIXE). In the case of AUG samples, where 25 nm thick W marker layers had been deposited on unpolished and polished graphite substrates, the effect of surface roughness on local erosion and deposition was also investigated. The lateral distribution of W concentration showed that erosion is much more distinct in the case of polished samples and the resulting surface shows a “leopard” skin pattern of W accumulated on carbon aggregates left on the surface from polishing. The Pilot-PSI samples indicated preferential accumulation of deuterium a few mm off from the centre of the region affected by the plasma beam. This is connected with the largest surface modifications while the thick deposited layers at the centre do not favour deuterium retention per se. The results were cross correlated with those obtained using laser-induced breakdown spectroscopy (LIBS). With its quantitative abilities, micro-NRA provided essential calibration data for in situ LIBS operation, as well as for complementary post mortem Secondary Ion Mass Spectroscopy (SIMS)Micro nuclear reaction analysis (micro-NRA) exploiting the nuclear reaction D(He-3,p)He-4 was used for post-mortem analyses of special marker samples, exposed to deuterium plasma inside ASDEX Upgrade (AUG) tokamak and to the deuterium plasma jet in the Pilot-PSI linear plasma gun. Lateral concentration profiles of deuterium and erosion/deposition profiles of the marker materials were obtained by a combination of micro-NRA and particle induced X-ray emission by He-3 beam (3HIXE). In the case of AUG samples, where 25 nm thick W marker layers had been deposited on unpolished and polished graphite substrates, the effect of surface roughness on local erosion and deposition was also investigated. The lateral distribution of W concentration showed that erosion is much more distinct in the case of polished samples and the resulting surface shows a "leopard" skin pattern of W accumulated on carbon aggregates left on the surface from polishing. The Pilot-PSI samples indicated preferential accumulation of deuterium a few mm off from the centre of the region affected by the plasma beam. This is connected with the largest surface modifications while the thick deposited layers at the centre do not favour deuterium retention per se. The results were cross correlated with those obtained using laser-induced breakdown spectroscopy (LIBS). With its quantitative abilities, micro-NRA provided essential calibration data for in situ LIES operation, as well as for complementary post mortem Secondary Ion Mass Spectroscopy (SIMS). (C) 2017 EURATOM. Published by Elsevier B.V. All rights reserved.Peer reviewe

LIBS plasma in atmospheric pressure argon, nitrogen and helium: Spatio-temporal distribution of plume emission and Hα linewidth

This work has been carried out within the framework of the EUROfusion Consortium, funded by the European Union via the Euratom Research and Training Programme (Grant Agreement No 101052200—EUROfusion). Views and opinions expressed are however those of the author(s) only and do not necessarily reflect those of the European Union or the European Commission. Neither the European Union nor the European Commission can be held responsible for them. Institute of Solid State Physics, University of Latvia as the Center of Excellence has received funding from the European Union’s Horizon 2020 Framework Programme H2020-WIDESPREAD-01-2016-2017-TeamingPhase2 under grant agreement No. 739508, project CAMART2.Laser Induced Breakdown Spectroscopy (LIBS) method is considered for assessing the retention of hydrogen isotopes in the ITER plasma-facing components during the maintenance breaks when the reactor is filled with near atmospheric pressure nitrogen or inert gas. At these conditions, the broadening of the spectral lines of hydrogen isotopes and the reduction of line intensities complicates the distinguishing of hydrogen isotopes. The aim of the present study was to investigate the effect of atmospheric pressure nitrogen, argon and helium ambient gas on the spatio-temporal distribution of the LIBS plasma plume emission and linewidths of Hα line, representing the hydrogen isotopes. Nd:YAG laser with 8 ns pulse width was used to ablate the molybdenum (Mo) target with hydrogen impurity. The development of the formed plasma plume was investigated by time and space-resolved emission spectra in the 20 nm range around the 656.28 nm Hα line. For all gases used in the experiments, the intensity and linewidth of Hα line decreased with the delay time between the laser pulse and the spectral registration. At the same linewidth values, the highest intensities were obtained in the helium atmosphere while the lowest intensity was obtained in nitrogen. According to spatially resolved spectral measurements, the Hα line was most intense near the Mo target while the Mo lines peaked farther away. In the case of the helium atmosphere, the plasma plume emission was observed at a longer distance from the target and it decayed faster than in argon and nitrogen atmospheres. According to these results, helium is the most beneficial ambient gas for hydrogen isotope detection by atmospheric pressure LIBS. The use of argon ambient gas may be required when LIBS is used for the simultaneous determination of fuel and He retention in the wall material. --//-- This is an open access article Indrek Jõgi, Jasper Ristkok, Jelena Butikova, Jüri Raud, Peeter Paris, LIBS plasma in atmospheric pressure argon, nitrogen and helium: Spatio-temporal distribution of plume emission and Hα linewidth, Nuclear Materials and Energy, Volume 37, 2023, 101543, ISSN 2352-1791, https://doi.org/10.1016/j.nme.2023.101543 published under the CC BY-NC-ND licence.EUROfusion Consortium Grant Agreement No 101052200; Institute of Solid State Physics, University of Latvia as the Center of Excellence has received funding from the European Union’s Horizon 2020 Framework Programme H2020-WIDESPREAD-01-2016-2017-TeamingPhase2 under grant agreement No. 739508, project CAMART2

Comparison of LIBS results on ITER-relevant samples obtained by nanosecond and picosecond lasers

This work has been carried out within the framework of the EUROfusion Consortium and has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement number 633053. The views and opinions expressed herein do not necessarily reflect those of the European Commission. Work performed under EUROfusion WP PFC.ITER foresees applying laser induced breakdown spectroscopy (LIBS) as a tool for quantitative assessment of fuel retention in the first walls. One open problem related to LIBS application is the choice of the laser type. Here we compare two Nd/YAG lasers with different pulse durations, 0.15 and 8 ns, working at λ = 1064 nm for LIBS studies of samples with D-doped W/Al coatings of ≈ 3 μm thickness (Al is used as a proxy of Be) on Mo. Low pressure argon was used as a background gas. Experiments were done in conditions where other factors (broadening of spectral lines, signal-to-noise ratio, limited thickness of coatings etc.) did not shadow the effect of laser pulse duration. For these reasons, low pressure argon was used as the background gas and fluences were kept at comparatively low values. Spectra of laser-produced plasma were recorded as a function of the number of laser pulses. Partially overlapping lines of hydrogen isotopes were fitted with Voigt contours, intensities were fitted and depth profiles of deuterium were reconstructed. The relative standard error of curve-fitting of spectra recorded with the laser of shorter pulse duration was two times smaller than that recorded by the longer pulse laser. The electron density was found from the Stark broadening of Hα line of the laser-produced plasma and the electron temperature of plasma was found on the basis W and Mo lines. It was found that in the case of ps laser an acceptable accuracy of the detection of deuterium was possible at considerably lower values of fluence. Steps needed for comparison of ps and ns lasers in ITER-relevant conditions were discussed.Horizon 2020 Framework Programme 633053; Institute of Solid State Physics, University of Latvia as the Center of Excellence has received funding from the European Union’s Horizon 2020 Framework Programme H2020-WIDESPREAD-01-2016-2017-TeamingPhase2 under grant agreement No. 739508, project CAMART

Determination of deuterium depth profiles in fusion-relevant wall materials by nanosecond LIBS

The ablation and fuel-retention characteristics of aluminum-tungsten (AlW) and beryllium-tungsten (BeW) samples have been determined using Laser Induced Breakdown Spectroscopy (LIBS) and compared to results obtained using Secondary Ion Mass Spectrometry (SIMS). The measurements have been made both at vacuum (of the order of 10-4 Pa) and at 50Pa of argon to especially enhance the intensities of the spectral lines of H and D. For reliable evaluation of the ablation rate of the samples the electron density ne and temperature Te of the LIBS plasma have been determined with the help of selected of spectral lines of Be, Al, and W. The electron density ne has been obtained from Stark broadening lines of Al I (308.7nm and 394.4nm) and Be II (457.3nm) and Te from the Saha-Boltzmann plot using W I and W II spectral lines having a higher value of the energy of upper states in order to prevent the influence of self-absorption on the results. The results indicate similar ablation characteristics between AlW (AlWD) and BeW(BeWD) samples but the inclusion of deuterium in the coating increases the ablation rate by a factor of 10 for both sample types. Concerning fuel retention more than one order of magnitude less D is retained in the AlWD sample than in BeWD. In the presence of background argon, the H and D lines were stronger and more easily distinguishable. This is a positive sign considering the real application in ITER where LIBS measurements are foreseen to be done during maintenance breaks. However the higher pressure gave a better signal, it is still far from the measurement conditions planned for ITER which need to be tested separately.Peer reviewe

Quantification of H/D content in Be/W mixtures coatings by CF-LIBS

| openaire: EC/H2020/633053/EU//EUROfusionIn ITER, a remote handling laser-induced breakdown spectroscopy (LIBS) system is considered to be able to observe regions where deposition of thick layers is expected to occur and assess the retention of fuel on wall structures. The H and D contents of surface layers on divertor and first-wall materials have been intensely studied by LIBS but mostly by depth profile analysis of D. As far as we know, quantitative analysis of H/D in BeW mixed layer by calibration free-LIBS (CF-LIBS) has not been performed. Thus, the aim of this work is the quantification of the relative concentrations of D and H in Be-based material samples by CF-LIBS. The samples used were Be/W(67:33) as mixed homogeneous coatings (2 μm) on Mo substrates. Laser ablation was performed using a 1064 nm laser with 5 ns pulses. In order to enhance the resolution to distinguish H, D and in future T from each other, two different pressures were used: high vacuum and 0.5 mbar of Ar. Suitable Be and W spectral lines (without interferences and self-absorption) have been selected for precise evaluation of the electron temperature, T e, of the plasma using the Boltzmann plots. The electron density, n e, was extracted from the Saha equation using the average electron temperatures obtained from the Stark broadening of the H α line. With these values, the D content of the samples has been calculated by CF LIBS as ∼4.7% ± 2.9%. These results are in a good agreement with thermal desorption spectroscopy measurements, which gives a 4-5 at% for the D content. In addition, the depth profile is similar to that recorded using secondary ion mass spectrometry.Peer reviewe