Utilization of temperature kinetics as a method to predict treatment intensity and corresponding treated wood quality : durability and mechanical properties of thermally modified wood

Wood heat treatment is an attractive alternative to improve decay resistance of wood species with low natural durability. However, this improvement of durability is realized at the expense of the mechanical resistance. Decay resistance and mechanical properties are strongly correlated to thermal degradation of wood cells wall components. Mass loss resulting from this degradation is a good indicator of treatment intensity and final treated wood properties. However, the introduction of a fast and accurate system for measuring this mass loss on an industrial scale is very difficult. Nowadays, many studies are conducted on the determination of control parameters which could be correlated with the treatment conditions and final heat treated wood quality such as decay resistance. The aim of this study is to investigate the relations between kinetics of temperature used during thermal treatment process representing heat treatment intensity, mass losses due to thermal degradation and conferred properties to heat treated wood. It might appear that relative area of treatment temperature curves is a good indicator of treatment intensity. Heat treatment with different treatment conditions (temperature-time) have been performed under vacuum, on four wood species (one hardwood and three softwoods) in order to obtain thermal degradation mass loses of 8, 10 and 12%. For each experiment, relative areas corresponding to temperature kinetics, mass loss, decay resistance and mechanical properties have been determined. Results highlight the statement that the temperature curves’ area constitutes a good indicator in the prediction of needed treatment intensity, to obtain required wood durability and mechanical properties such as bending resistance and Brinell hardness.LERMaB is supported by the French National Research Agency through the Laboratory of Excellence ARBRE (ANR-12- LABXARBRE-01), the authors gratefully acknowledge this ai

Experimental Comparative Study between Conventional and Green Parking Lots: Analysis of Subsurface Thermal Behavior under Warm and Dry Summer Conditions

Green infrastructure has a role to play in climate change adaptation strategies in cities. Alternative urban spaces should be designed considering new requirements in terms of urban microclimate and thermal comfort. Pervious pavements such as green parking lots can contribute to this goal through solar evaporative cooling. However, the cooling benefits of such systems remain under debate during dry and warm periods. The aim of this study was to compare experimentally the thermal behavior of different parking lot types (PLTs) with vegetated urban soil. Four parking lots were instrumented, with temperature probes buried at different depths. Underground temperatures were measured during summer 2019, and the hottest days of the period were analyzed. Results show that the less mineral used in the surface coating, the less it warms up. The temperature difference at the upper layer can reach 10 °C between mineral and non-mineral PLTs. PLTs can be grouped into three types: (i) high surface temperature during daytime and nighttime, important heat transfer toward the sublayers, and low time shift (asphalt system); (ii) high (resp. low) surface temperature during daytime (resp. nighttime), weak heat transfer toward the sublayers, and important time shift (paved stone system); and (iii) low surface temperature during daytime and nighttime, weak heat transfer toward the sublayers, and important time shift (vegetation and substrate system, wood chips system, vegetated urban soil). The results of this study underline that pervious pavements demonstrate thermal benefits under warm and dry summer conditions compared to conventional parking lot solutions. The results also indicate that the hygrothermal properties of urban materials are crucial for urban heat island mitigation

Furanic Polymerization Causes the Change, Conservation and Recovery of Thermally-Treated Wood Hydrophobicity before and after Moist Conditions Exposure

The Whilhelmy method of contact angle, wood thermal properties (TG/DTG), infrared spectroscopy, etc. was used to define the hydrophobicity of heat-treated beech and fir wood at increasing temperatures between 120 °C and 300 °C. By exposure to wet conditions during 1 week, the hydrophobic character obtained by the heat treatment remains constant heat-treated. Heat induced wood hydrophobation, was shown by CP MAS 13C NMR and MALDI ToF mass spectrometry to be mainly caused by furanic moieties produced from heat-induced hemicelluloses degradation. This is caused by the acid environment generated by the hydrolysis of the hemicelluloses acetyl groups. Furfural polymerizes to linear and branched oligomers and finally to water repellent, insoluble furanic resins. The water repellent, black colored, cross-linked polymerized furanic network is present throughout the heat-treated wood. Wood darkening as well as its water repellency due to increasing proportions of black colored furanic resins increase as a function of the increase with treating temperature, becoming particularly evident in the 200 to 300 °C treating temperature range

Highly Branched Tannin-Tris(2-aminoethyl)amine-Urea Wood Adhesives

Condensed tannin copolymerized with hyperbranched tris(2-aminoethyl)amine-urea formed by amine-amido deamination yields a particleboard thermosetting adhesive without any aldehydes satisfying the requirements of relevant standards for the particleboard internal bond strength. The tannin–triamine–urea cures well at 180 °C, a relatively low temperature for today’s particleboard hot pressing. As aldehydes were not used, the formaldehyde emission was found to be zero, not even in traces due to the heating of wood. The effect is ascribed to the presence of many reactive sites, such as amide, amino, and phenolic groups belonging to the three reagents used. The tannin appears to function as an additional cross-linking agent, almost a nucleating agent, for the triamine–urea hyperbranched oligomers. Chemical analysis by MALDI ToF and 13C NMR has shown that the predominant cross-linking reaction is that of the substitution of the tannin phenolic hydroxyls by the amino groups of the triamine. The reaction of tannin with the still-free amide groups of urea is rather rare, but it may occur with the rarer tannin flavonoid units in which the heterocyclic ring is opened. Due to the temperature gradient between the surfaces and the board core in the particleboard during hot pressing, the type and the relative balance of covalent and ionic bonds in the resin structure may differ in the surfaces and the board core

Catalytic effects of potassium on biomass pyrolysis, combustion and torrefaction

Potassium is a natural catalyst in biomass thermochemical conversion and plays an essential role in plant's growth. To figure out the catalytic effects of potassium on the thermochemical behaviors of biomass, the pyrolysis, combustion, and torrefaction characteristics of rubber wood are comprehensively studied using a thermogravimetric analyzer where the biomass is impregnated by potassium carbonate (K2CO3) at different concentrations. The impregnated potassium is clearly exhibited in the spectra of Fourier-transform infrared spectroscopy, while X-ray diffraction indicate that the cellulose crystallinity decreases with increasing the potassium concentration which increases the biomass reactivity in pyrolysis. The ignition temperature of the potassium-impregnated biomass is lowered slightly when compared with the raw biomass; alternatively, its burnout temperature is reduced profoundly, suggesting that the addition of potassium into the biomass can substantially intensify its oxidative reactivity. Considering the treated biomass torrefaction, its cellulose decomposition at 250 degrees C is intensified, rendering a reduction in the solid yield with increasing potassium concentration. With the same mass loss at 200-300 degrees C, at least 28% of torrefaction time can be saved for the potassium-impregnated biomass. Accordingly, the catalytic effect of potassium on biomass thermochemical conversion is clearly outlined. Moreover, the produced potassium-rich biochar is conducive to the developments of carbon storage, soil amendment, and negative emissions technologies.Web of Science23535534