Functional Independence Measure in Iran: A Confirmatory Factor Analysis and Evaluation of Ceiling and Floor Effects in Traumatic Brain Injury Patients

Background: The functional independence measure (FIM) is one of the most important assessment instruments for motor and cognitive dependence in rehabilitation medicine; however, there is little data about its confirmatory factor analysis (CFA) and ceiling/floor effects from other countries and also in Iranian patients. Objectives: The aim of this study was to evaluate a two-factor model (motor and cognitive independence as latent variables) and ceiling/floor effects for FIM in Iranian patients with traumatic brain injuries (TBI). Patients and Methods: In this cross-sectional study, 185 subacute TBI patients were selected from emergency and neurosurgery departments of Poursina Hospital (the largest trauma hospital in northern Iran, Rasht) using the consecutive sampling method and were assessed for functional independence. Results: The results of this study showed that the floor effect was not observed; however, ceiling effects were observed for the FIM total score and its subscales. The confirmatory factor analysis showed that the chi-square/df ratio was 2.8 for the two-factor structure and the fit indices for this structural model including root mean square error of approximation (RMSEA) = 0.099, normed fit index (NFI) = 0.96, tucker lewis index (TLI) = 0.97, comparative fit index (CFI) = 0.97 were close to standard indices. Conclusions: Although ceiling effects should be considered for rehabilitation targets, the two-factor model of FIM (motor and cognitive independence) has an eligible fitness for Iranian patients with TBI

Comparison of non-electrophoresis grade with electrophoresis grade BIS in NIPAM polymer gel preparation

Introduction: The main objective of this study was to investigate the possibility of replacing electrophoresis cross-linker with non-electrophoresis N, N'-methylenebisacrylamide (BIS) in N-isopropyl acrylamide (NIPAM) polymer gel and its possible effect on dose response. Methods: NIPAM polymer gel was prepared from non-electrophoresis grade BIS and the relaxation rate (R-2) was measured by MR imaging after exposing the gel to gamma radiation from Co-60 source. To compare the response of this gel with the one that contains electrophoresis grade BIS, two sets of NIPAM gel were prepared using electrophoresis and non-electrophoresis BIS and irradiated to different gamma doses. Results: It was found that the dose-response of NIPAM gel made from the non-electrophoresis grade BIS is coincident with that of electrophoresis grade BIS. Conclusion: Taken all, it can be concluded that the non-electrophoresis grade BIS not only is a suitable alternative for the electrophoresis grade BIS but also reduces the cost of gel due to its lower price

Additive manufacturing of bioactive glass biomaterials

Tissue engineering (TE) and regenerative medicine have held great promises for the repair and regeneration of damaged tissues and organs. Additive manufacturing has recently appeared as a versatile technology in TE strategies that enables the production of objects through layered printing. By applying 3D printing and bioprinting, it is now possible to make tissue-engineered constructs according to desired thickness, shape, and size that resemble the native structure of lost tissues. Up to now, several organic and inorganic materials were used as raw materials for 3D printing; bioactive glasses (BGs) are among the most hopeful substances regarding their excellent properties (e.g., bioactivity and biocompatibility). In addition, the reported studies have confirmed that BG-reinforced constructs can improve osteogenic, angiogenic, and antibacterial activities. This review aims to provide an up-to-date report on the development of BG-containing raw biomaterials that are currently being employed for the fabrication of 3D printed scaffolds used in tissue regeneration applications with a focus on their advantages and remaining challenges

Evidence of coexistence of change of caged dynamics at Tg and the dynamic transition at Td in solvated proteins

Mossbauer spectroscopy and neutron scattering measurements on proteins embedded in solvents including water and aqueous mixtures have emphasized the observation of the distinctive temperature dependence of the atomic mean square displacements, , commonly referred to as the dynamic transition at some temperature Td. At low temperatures, increases slowly, but it assume stronger temperature dependence after crossing Td, which depends on the time/frequency resolution of the spectrometer. Various authors have made connection of the dynamics of solvated proteins including the dynamic transition to that of glass-forming substances. Notwithstanding, no connection is made to the similar change of temperature dependence of obtained by quasielastic neutron scattering when crossing the glass transition temperature Tg, generally observed in inorganic, organic and polymeric glass-formers. Evidences are presented to show that such change of the temperature dependence of from neutron scattering at Tg is present in hydrated or solvated proteins, as well as in the solvents used unsurprisingly since the latter is just another organic glass-formers. The obtained by neutron scattering at not so low temperatures has contributions from the dissipation of molecules while caged by the anharmonic intermolecular potential at times before dissolution of cages by the onset of the Johari-Goldstein beta-relaxation. The universal change of at Tg of glass-formers had been rationalized by sensitivity to change in volume and entropy of the beta-relaxation, which is passed onto the dissipation of the caged molecules and its contribution to . The same rationalization applies to hydrated and solvated proteins for the observed change of at Tg.Comment: 28 pages, 10 figures, 1 Tabl

In situ production of titanium dioxide nanoparticles in molten salt phase for thermal energy storage and heat-transfer fluid applications

In this study, TiO2 nanoparticles (average particle size 16 nm) were successfully produced in molten salt phase and were showed to significantly enhance the specific heat capacity of a binary eutectic mixture of sodium and potassium nitrate (60/40) by 5.4 % at 390 °C and 7.5 % at 445 °C for 3.0 wt% of precursors used. The objective of this research was to develop a cost-effective alternate method of production which is potentially scalable, as current techniques utilized are not economically viable for large quantities. Enhancing the specific heat capacity of molten salt would promote more competitive pricing for electricity production by concentrating solar power plant. Here, a simple precursor (TiOSO4) was added to a binary eutectic mixture of potassium and sodium nitrate, heated to 450 °C, and cooled to witness the production of nanoparticles

Low-Temperature Polymorphic Phase Transition in a Crystalline Tripeptide L-Ala-L-Pro-Gly·H2O Revealed by Adiabatic Calorimetry

We demonstrate application of precise adiabatic vacuum calorimetry to observation of phase transition in the tripeptide l-alanyl-l-prolyl-glycine monohydrate (APG) from 6 to 320 K and report the standard thermodynamic properties of the tripeptide in the entire range. Thus, the heat capacity of APG was measured by adiabatic vacuum calorimetry in the above temperature range. The tripeptide exhibits a reversible first-order solid-to-solid phase transition characterized by strong thermal hysteresis. We report the standard thermodynamic characteristics of this transition and show that differential scanning calorimetry can reliably characterize the observed phase transition with <5 mg of the sample. Additionally, the standard entropy of formation from the elemental substances and the standard entropy of hypothetical reaction of synthesis from the amino acids at 298.15 K were calculated for the studied tripeptide.National Institute of Biomedical Imaging and Bioengineering (U.S.) (EB-003151)National Institute of Biomedical Imaging and Bioengineering (U.S.) (EB-001960)National Institute of Biomedical Imaging and Bioengineering (U.S.) (EB-002026