53 research outputs found
Demonstration of a Transportable 1 Hz-Linewidth Laser
We present the setup and test of a transportable clock laser at 698 nm for a
strontium lattice clock. A master-slave diode laser system is stabilized to a
rigidly mounted optical reference cavity. The setup was transported by truck
over 400 km from Braunschweig to D\"usseldorf, where the cavity-stabilized
laser was compared to a stationary clock laser for the interrogation of
ytterbium (578 nm). Only minor realignments were necessary after the transport.
The lasers were compared by a Ti:Sapphire frequency comb used as a transfer
oscillator. The thus generated virtual beat showed a combined linewidth below 1
Hz (at 1156 nm). The transport back to Braunschweig did not degrade the laser
performance, as was shown by interrogating the strontium clock transition.Comment: 3 pages, 4 figure
The Space Optical Clocks Project: Development of high-performance transportable and breadboard optical clocks and advanced subsystems
The use of ultra-precise optical clocks in space ("master clocks") will allow
for a range of new applications in the fields of fundamental physics (tests of
Einstein's theory of General Relativity, time and frequency metrology by means
of the comparison of distant terrestrial clocks), geophysics (mapping of the
gravitational potential of Earth), and astronomy (providing local oscillators
for radio ranging and interferometry in space). Within the ELIPS-3 program of
ESA, the "Space Optical Clocks" (SOC) project aims to install and to operate an
optical lattice clock on the ISS towards the end of this decade, as a natural
follow-on to the ACES mission, improving its performance by at least one order
of magnitude. The payload is planned to include an optical lattice clock, as
well as a frequency comb, a microwave link, and an optical link for comparisons
of the ISS clock with ground clocks located in several countries and
continents. Undertaking a necessary step towards optical clocks in space, the
EU-FP7-SPACE-2010-1 project no. 263500 (SOC2) (2011-2015) aims at two
"engineering confidence", accurate transportable lattice optical clock
demonstrators having relative frequency instability below 1\times10^-15 at 1 s
integration time and relative inaccuracy below 5\times10^-17. This goal
performance is about 2 and 1 orders better in instability and inaccuracy,
respectively, than today's best transportable clocks. The devices will be based
on trapped neutral ytterbium and strontium atoms. One device will be a
breadboard. The two systems will be validated in laboratory environments and
their performance will be established by comparison with laboratory optical
clocks and primary frequency standards. In this paper we present the project
and the results achieved during the first year.Comment: Contribution to European Frequency and Time Forum 2012, Gothenburg,
Swede
FORECASTING THE PROFESSIONAL FUTURE OF THE SUBJECT OF ACTIVITY IN THE SPHERE OF STATE AND MUNICIPAL MANAGEMENT
В статье рассматривается вопрос о прогнозировании профессионального будущего субъекта деятельности в сфере государственного и муниципального управления на основании нового целевого ориентира – служение государствуThe article deals with the issue of forecasting the professional future of the subject of activity in the field of state and municipal management on the basis of a new target – service to the stat
Ultra-precise measurement of optical frequency ratios
We developed a novel technique for frequency measurement and synthesis, based
on the operation of a femtosecond comb generator as transfer oscillator. The
technique can be used to measure frequency ratios of any optical signals
throughout the visible and near-infrared part of the spectrum. Relative
uncertainties of for averaging times of 100 s are possible. Using a
Nd:YAG laser in combination with a nonlinear crystal we measured the frequency
ratio of the second harmonic at 532 nm to the fundamental at
1064 nm, .Comment: 4 pages, 4 figure
A vibration-insensitive optical cavity and absolute determination of its ultrahigh stability
We use the three-cornered-hat method to evaluate the absolute frequency
stabilities of three different ultrastable reference cavities, one of which has
a vibration-insensitive design that does not even require vibration isolation.
An Nd:YAG laser and a diode laser are implemented as light sources. We observe
Hz beat note linewidths between all three cavities. The measurement
demonstrates that the vibration-insensitive cavity has a good frequency
stability over the entire measurement time from 100 s to 200 s. An
absolute, correlation-removed Allan deviation of at 1 s of
this cavity is obtained, giving a frequency uncertainty of only 0.44 Hz.Comment: 13 pages, 10 figure
A Nd:YAG Laser with short-term frequency stability at the Hertz-level
We report on the frequency stabilisation of a Nd:YAG laser at 946 nm to the Hertz-level. The laser will be used for ultra- high resolution spectroscopy of the 5s(2) S-1(0) - 5s5p P-3(0) transition in In+ and will ultimately serve as a local oscillator of an optical frequency standard based on a single trapped indium ion. To resolve the extremely narrow S-1(0) - P- 3(0) resonance (natural linewidth 0.82 Hz) at 237 nm, the frequency-quadrupled Nd:YAG laser radiation has to be frequency stable at the Hertz-scale for measurement times up to several tens of seconds. We obtain the frequency stability of the laser by locking it onto an external reference cavity of high finesse, placed on an active vibration isolation platform. (C) 2002 Elsevier Science B.V. All rights reserved
- …