Current-Induced Effective Magnetic Fields in Co/Cu/Co Nanopillars

We present a method to measure the effective field contribution to spin-transfer-induced interactions between the magnetic layers in a trilayer nanostructure, which enables spin-current effects to be distinguished from the usual charge-current-induced magnetic fields. This technique is demonstrated on submicron Co/Cu/Co nanopillars. The hysteresis loop of one of the magnetic layers in the trilayer is measured as a function of current while the direction of magnetization of the other layer is kept fixed, first in one direction and then in the opposite direction. These measurements show a current-dependent shift of the hysteresis loop which, based on the symmetry of the magnetic response, we associate with spin-transfer. The observed loop-shift with applied current at room temperature is reduced in measurements at 4.2 K. We interprete these results both in terms of a spin-current dependent effective activation barrier for magnetization reversal and a spin-current dependent effective magnetic field. From data at 4.2 K we estimate the magnitude of the spin-transfer induced effective field to be $\sim 1.5 \times 10^{-7}$ Oe cm$^2$/A, about a factor of 5 less than the spin-transfer torque.Comment: 6 pages, 4 figure

A Comparison of Anaerobic Power Tests using Cycle Ergometry and Non-motorized Treadmill Ergometry at Optimized Loads

International Journal of Exercise Science 16(4): 1293-1305, 2023. The purpose of this study was to compare performance markers derived from a 30-second maximal bout on a cycle ergometer (CE) and non-motorized treadmill (NMT) under optimized loads. Recreationally active participants (n = 40) volunteered for the study. Force-velocity tests on the CE and NMT were used to determine optimal resistance for peak power (PP) production. The remaining visits were randomized and counterbalanced, with a single 30-second maximal test on CE or NMT to assess PP, mean power (MP), fatigue index (FI), over the course of the 30-second test, and maximum heart rate (HRmax) and blood lactate (BLa-) taken 1-minute post. Results were that PP and MP were higher (P\u3c0.05) on CE compared to NMT for both sexes. FI did not differ among males (P=0.201) whereas females showed higher FI (P=0.002) on the CE. HRmax and BLa- were higher (P\u3c0.05) after NMT for both sexes. There was no difference for optimal braking force on NMT between males (16.65±4.49%BW) and females (14.30±3.10%BW) (P=0.061). CE optimal torque factor was higher for males (0.78±0.16 Nm/kg) compared to females (0.62±0.14 Nm/kg) (P=0.001). Overall, CE produced higher power output using optimized loads in recreationally active males and females, while NMT test resulted in a higher HRmax andBLa- concentration. These tests for anaerobic power, when performed with optimized loads, produced different results for several variables, therefore these modalities should not be considered interchangeable. Practitioners should consider which modality best mimics the activities of the person being tested when selecting a protocol

Robotic manipulation for the shoe-packaging process

[EN] This paper presents the integration of a robotic system in a human-centered environment, as it can be found in the shoe manufacturing industry. Fashion footwear is nowadays mainly handcrafted due to the big amount of small production tasks. Therefore, the introduction of intelligent robotic systems in this industry may contribute to automate and improve the manual production steps, such us polishing, cleaning, packaging, and visual inspection. Due to the high complexity of the manual tasks in shoe production, cooperative robotic systems (which can work in collaboration with humans) are required. Thus, the focus of the robot lays on grasping, collision detection, and avoidance, as well as on considering the human intervention to supervise the work being performed. For this research, the robot has been equipped with a Kinect camera and a wrist force/ torque sensor so that it is able to detect human interaction and the dynamic environment in order to modify the robot¿s behavior. To illustrate the applicability of the proposed approach, this work presents the experimental results obtained for two actual platforms, which are located at different research laboratories, that share similarities in their morphology, sensor equipment and actuation system.This work has been partly supported by the Ministerio de Economia y Competitividad of the Spanish Government (Key No.: 0201603139 of Invest in Spain program and Grant No. RTC-2016-5408-6) and by the Deutscher Akademischer Austauschdienst (DAAD) of the German Government (Projekt-ID 54368155).Gracia Calandin, LI.; Perez-Vidal, C.; Mronga, D.; Paco, JD.; Azorin, J.; Gea, JD. (2017). Robotic manipulation for the shoe-packaging process. The International Journal of Advanced Manufacturing Technology. 92(1-4):1053-1067. https://doi.org/10.1007/s00170-017-0212-6S10531067921-4Pedrocchi N, Villagrossi E, Cenati C, Tosatti LM (2017) Design of fuzzy logic controller of industrial robot for roughing the uppers of fashion shoes. Int J Adv Manuf Technol 77(5):939–953Hinojo-Perez JJ, Davia-Aracil M, Jimeno-Morenilla A, Sanchez-Romero L, Salas F (2016) Automation of the shoe last grading process according to international sizing systems. Int J Adv Manuf Technol 85(1):455–467Dura-Gil JV, Ballester-Fernandez A, Cavallaro M, Chiodi A, Ballarino A, von Arnim V., Brondi C, Stellmach D (2016) New technologies for customizing products for people with special necessities: project fashion-able. Int J Comput Integr Manuf. In Press, doi: 10.1080/0951192X.2016.1145803Jatta F, Zanoni L, Fassi I, Negri S (2004) A roughing/cementing robotic cell for custom made shoe manufacture. Int J Comput Integr Manuf 17(7):645–652Nemec B, Zlajpah L (2008) Robotic cell for custom finishing operations. Int J Comput Integr Manuf 21(1):33–42Molfino R, et al (2004) Modular, reconfigurable prehensor for grasping and handling limp materials in the shoe industry. In: IMS international forum, CernobbioIntelishoe - integration and linking of shoe and auxiliary industries. 5Th FPSpecial shoes movement. 7th FP, NMP-2008-SME-2-R.229261, http://www.sshoes.euVilaca JL, Fonseca J (2007) A new software application for footwear industry. In: IEEE international symposium on intelligent signal processing WISP 2007, pp 1–6Custom, environment and comfort made shoe. 6TH FP [2004-2008]Framework of integrated technologies for user centred products. Grant agreement no.: CP-TP 229336-2. NMP2-SE-2009-229336 FIT4U -7TH FPRobofoot project website. http://www.robofoot.eu/ . Accessed 2016/ 09/16Montiel E (2007) Customization in the footwear industry. In: proceedings of the MIT congress on mass customizationSucan I, Kavraki LE (2012) A sampling-based tree planner for systems with complex dynamics, vol 28Kuffner JJ Jr, LaValle SM (2000) Rrt-connect: an efficient approach to single-query path planning. In: Proceedings of the IEEE international conference on robotics and automation, 2000. ICRA ’00, vol 2, pp 995–1001Ratliff N, Zucker M, Andrew Bagnell J, Srinivasa S (2009) Chomp: gradient optimization techniques for efficient motion planning. In: IEEE international conference on robotics and automation, 2009. ICRA ’09, pp 489–494Brock O, Khatib O (1997) Elastic strips: real-time path modification for mobile manipulationKroger T (2011) Opening the door to new sensor-based robot applications #x2014;the reflexxes motion libraries. In: 2011 IEEE international conference on robotics and automation (ICRA), pp 1–4Berg J, Ferguson D, Kuffner J (2006) Anytime path planning and replanning in dynamic environments. In: Proceedings of the IEEE international conference on robotics and automation (ICRA), pp 2366–2371Berenson D, Abbeel P, Goldberg K (2012) A robot path planning framework that learns from experience. In: IEEE international conference on robotics and automation. IEEE, pp 3671–3678Bischoff R, Kurth J, Schreiber G, Koeppe R, Albu-Schaeffer A, Beyer A, Eiberger O, Haddadin S, Stemmer A, Grunwald G, Hirzinger G (2010) The kuka-dlr lightweight robot arm — a new reference platform for robotics research and manufacturing. In: Robotics (ISR), 2010 41st international symposium on and 2010 6th German conference on robotics (ROBOTIK), pp 1–8Rooks B (2006) The harmonious robot. Industrial Robot-an International Journal 33:125–130Vahrenkamp N, Wieland S, Azad P, Gonzalez D, Asfour T, Dillmann R (2008) Visual servoing for humanoid grasping and manipulation tasks. In: 8th IEEE-RAS international conference on humanoid robots, 2008, Humanoids 2008, pp 406–412Pieters RS, et al. (2012) Direct trajectory generation for vision-based obstacle avoidance. In: Proceedings of the 2012 IEEE/RSJ international conference on intelligent robots and systemsKinect for windows sensor components and specifications, website. http://msdn.microsoft.com/en-us/library/jj131033.aspx . Accessed 2016/09/16Jatta F, Zanoni L, Fassi I, Negri S (2004) A roughing cementing robotic cell for custom made shoe manufacture. Int J Comput Integr Manuf 17(7):645–652Maurtua I, Ibarguren A, Tellaeche A (2012) Robotics for the benefit of footwear industry. In: International conference on intelligent robotics and applications. Springer, Berlin, pp 235–244Arkin RC (1998) Behavior-based robotics. MIT PressNilsson NJ (1980) Principles of artificial intelligence. Morgan KaufmannAsada H, Slotine J-JE (1986) Robot analysis and control. WileyROS official web page. http://www.ros.org , (Accessed on 2017/ 02/03)Langmann B, Hartmann K, Loffeld O (2012) Depth camera technology comparison and performance evaluation. In: 1st international conference on pattern recognition applications and methods, pp 438–444The player project. free software tools for robot and sensor applications. http://playerstage.sourceforge.net/ , (Accessed on 2017/ 02/03)Yet another robot platform (YARP). http://www.yarp.it/ , (Accessed on 2017/02/03)The OROCOS project. smarter control in robotics and automation. http://www.orocos.org/ , (Accessed on 2017/02/03)CARMEN: Robot navigation toolkit. http://carmen.sourceforge.net/ , (Accessed on 2017/02/03)ORCA: Components for robotics. http://orca-robotics.sourceforge.net/ , (Accessed on 2017/02/03)MOOS: Mission oriented operating suite. http://www.robots.ox.ac.uk/mobile/MOOS/wiki/pmwiki.php/Main/HomePage , (Accessed on 2017/02/03)Microsoft robotics studio. https://www.microsoft.com/en-us/download/details.aspx?id=29081 , (Accessed on 2017/02/03)Pr2 ros website. http://www.ros.org/wiki/Robots/PR2 . Accessed 2016/09/16Care-o-bot 3 ros website. http://www.ros.org/wiki/Robots/Care-O-bot . Accessed 2016/09/16Aila, mobile dual-arm manipulation, website. http://robotik.dfki-bremen.de/de/forschung/robotersysteme/aila.html . Accessed 2016/09/16Package libpcan documentation, website. http://www.ros.org/wiki/libpcan . Accessed 2016/09/16Pcan driver for linux, user manual. http://www.peak-system.com . Document version 7.1 (2011-03-21)Pcan driver for linux, user manual. http://wiki.ros.org/schunk_powercube_chain . Accessed 2016/09/16Ros nodes documentation, website. http://www.ros.org/wiki/Nodes . Accessed 2016/09/16Ros messages documentation, website. http://www.ros.org/wiki/Messages . Accessed 2016/09/16Ros topics documentation, website. http://www.ros.org/wiki/Topics . Accessed 2016/09/16Ros services documentation, website. http://www.ros.org/wiki/Services . Accessed 2016/09/16Yaml files officials website. http://www.yaml.org/ . Accessed 2016/ 09/16Ros robot model (urdf) documentation website. http://www.ros.org/wiki/urdf . Accessed 2016/09/16Point cloud library (pcl), website. http://www.pointclouds.org/ . Accessed 2016/09/16Arm navigation ros stack, website. http://wiki.ros.org/arm_navigation . Accessed 2016/09/16Hornung A, Wurm KM, Bennewitz M, Stachniss C, Burgard W (2013) Octomap: an efficient probabilistic 3d mapping framework based on octrees Autonomous RobotsOrocos kdl documentation, website. http://www.orocos.org/kdl . Accessed 2016/09/16Ioan A, Şucan MM, Kavraki LE (2012) The open motion planning library, vol 19. http://ompl.kavrakilab.orgWaibel M, Beetz M, Civera J, D’Andrea R, Elfring J, Galvez-Lopez D, Haussermann K, Janssen R, Montiel JMM, Perzylo A, Schiessle B, Tenorth M, Zweigle O, van de Molengraft R (2011) Roboearth. IEEE Robot Autom Mag 18(2):69–82Simox toolbox. http://simox.sourceforge.net/ . Accessed 2016/09/16Moreels P, Perona P (2007) Evaluation of features detectors and descriptors based on 3d objects. Int J Comput Vis 73:263–284Viola P, Jones M (2001) Rapid object detection using a boosted cascade of simple features. In: Proceedings of the IEEE computer society conference on computer vision and pattern recognition, 2001. CVPR 2001, vol 1Teuliere C, Marchand E, Eck L (2010) Using multiple hypothesis in model-based tracking. In: 2010 IEEE international conference on robotics and automation (ICRA), pp 4559–4565Moulianitis VC, Dentsoras AJ, Aspragathos NA (1999) A knowledge-based system for the conceptual design of grippers for handling fabrics. Artif Intell Eng Des Anal Manuf 13(1):13–25Davis S, Tsagarakis NG, Caldwell DG (2008) The initial design and manufacturing process of a low cost hand for the robot icub. In: 8th IEEE-RAS international conference on humanoid robots, pp 40–45Cerruti G, Chablat D, Gouaillier D, Sakka S (2017) Design method for an anthropomorphic hand able to gesture and grasp. In: IEEE international conference on robotics and automation. IEEE, pp 3671–367

11-[3-(Dimethyl­amino)prop­yl]-6,11-dihydro­dibenzo[b,e]thiepin-11-ol

There are two independent mol­ecules (A and B) in the asymmetric unit of the title compound, C19H23NOS. In each mol­ecule, the seven-membered thiepine ring is bent into a slightly twisted V-shape. The dihedral angles between the mean planes of the two benzene rings fused to the thiepine ring are 75.7 (5) in mol­ecule A and 73.8 (4)° in mol­ecule B. In both mol­ecules, an intra­molecular O—H⋯N hydrogen bond occurs. In the crystal, weak inter­molecular C—H⋯O and C—H⋯π-ring inter­actions are observed

Shapes, contact angles, and line tensions of droplets on cylinders

Using an interface displacement model we calculate the shapes of nanometer-size liquid droplets on homogeneous cylindrical surfaces. We determine effective contact angles and line tensions, the latter defined as excess free energies per unit length associated with the two contact lines at the ends of the droplet. The dependences of these quantities on the cylinder radius and on the volume of the droplets are analyzed.Comment: 26 pages, RevTeX, 10 Figure

Community Occupational Therapy in Dementia intervention for people with mild to moderate dementia and their family carers in the UK: the VALID research programme including RCT

BACKGROUND: People with dementia find it increasingly difficult to carry out daily activities (activities of daily living), and may require increasing support from family carers. Researchers in the Netherlands developed the Community Occupational Therapy in Dementia intervention, which was delivered in 10 1-hour sessions over 5 weeks to people with dementia and their family carers at home. Community Occupational Therapy in Dementia was found to be clinically effective and cost-effective. OBJECTIVES: Translate and adapt Community Occupational Therapy in Dementia to develop the Community Occupational Therapy in Dementia - the UK version intervention and training programme and to optimise its suitability for use within the UK. To estimate the clinical effectiveness and cost-effectiveness of Community Occupational Therapy in Dementia - the UK version for people with mild to moderate dementia and their family carers compared with treatment as usual. DESIGN: The development phase used mixed methods to develop Community Occupational Therapy in Dementia - the UK version: translation, expert review, and adaptation of the manual and training materials; training occupational therapists; focus groups and interviews, including occupational therapists, managers, people with dementia and family carers; consensus conference; and an online survey of occupational therapists to scope UK practice. A multicentre, two-arm, parallel-group, single-blind individually randomised pragmatic trial was preceded by an internal pilot. Pairs were randomly allocated between Community Occupational Therapy in Dementia - the UK version and treatment as usual. A cost–utility analysis, fidelity study and qualitative study were also completed. SETTING: Community services for people with dementia across England. PARTICIPANTS: People with mild to moderate dementia recruited in pairs with a family carer/supporter. INTERVENTIONS: Community Occupational Therapy in Dementia - the UK version is an activity-based, goal-setting approach for people with dementia and family carers, and is delivered at home by an occupational therapist for 10 hours over 10 weeks. Treatment as usual comprised the usual local service provision, which may or may not include standard occupational therapy. MAIN OUTCOMES MEASURES: Data were collected through interviews conducted in person with dyads at baseline and at 12 and 26 weeks post randomisation, and then over the telephone with a reduced sample of just carers at 52 and 78 weeks post randomisation. The primary outcome was the Bristol Activities of Daily Living Scale at 26 weeks. The secondary outcomes were as follows: person with dementia – cognition, activities of daily living, quality of life and mood; carer – sense of competence, quality of life and mood; all participants – social contacts, leisure activities and serious adverse events. RESULTS: The Community Occupational Therapy in Dementia manual and training materials were translated and reviewed. In total, 44 occupational therapists were trained and delivered Community Occupational Therapy in Dementia to 130 pairs. A total of 197 occupational therapists completed the survey, of whom 138 also provided qualitative data. In total, 31 people attended the consensus conference. Community Occupational Therapy in Dementia - the UK version has more flexibility than Community Occupational Therapy in Dementia in terms of content and delivery; for example, occupational therapists can use the wider range of assessment tools that are already in regular use within UK practice and the time span for delivery is 10 weeks to better meet the needs of pairs and be more feasible for services to deliver. In total, 31 occupational therapists provided Community Occupational Therapy in Dementia - the UK version within the randomised controlled trial. A total of 468 pairs were randomised (249 pairs to Community Occupational Therapy in Dementia - the UK version, 219 pairs to treatment as usual). People with dementia ranged in age from 55 to 97 years (mean 78.6 years), and family carers ranged in age from 29 to 94 years (mean 69.1 years). The majority of those with dementia (74.8%) were married; 19.2% lived alone. Most family carers (72.6%) were spouses but 22.2% were adult children. At 26 weeks, 406 (87%) pairs remained in the trial, and the Bristol Activities of Daily Living Scale total score did not differ at the 5% level when comparing groups (adjusted mean difference estimate 0.35, 95% confidence interval –0.81 to 1.51; p = 0.55). The adjusted (for baseline Bristol Activities of Daily Living Scale total score and randomised group) intracluster correlation coefficient estimate at week 26 was 0.043. There were no significant differences in secondary outcomes. At 52 and 78 weeks, there were no differences between the two groups in Bristol Activities of Daily Living Scale total score and secondary outcomes. The probability that Community Occupational Therapy in Dementia - the UK version is cost-effective at a threshold of willingness to pay per quality-adjusted life-year of £20,000 is 0.02%. In the qualitative interviews, participants reported positive benefits and outcomes. Of the 249 pairs allocated to Community Occupational Therapy in Dementia - the UK version, 227 reached the goal-setting phase, and 838 of the 920 goals set (90.8%) were fully or partially achieved. LIMITATIONS: The development phase took longer than estimated because of translation time and organisational delays in delivering the intervention. Recruitment to the randomised controlled trial took longer than expected. Fidelity overall was moderate, with variation across sites and therapists. It is possible that Community Occupational Therapy in Dementia - the UK version did not work well in the UK service model in which usual care differs from that in the Netherlands. CONCLUSIONS: This programme used a rigorous process to develop Community Occupational Therapy in Dementia - the UK version but found no statistical evidence of clinical effectiveness or cost-effectiveness compared with usual care. Qualitative findings provided positive examples of how Community Occupational Therapy in Dementia - the UK version had enabled people to live well with dementia. FUTURE WORK: Developing tools to measure more meaningful outcomes, such as goals achieved or the quantity and quality of activity participation, with less reliance on proxy data, to collect the views and experiences of people with dementia themselves. TRIAL REGISTRATION: This trial was registered as ISRCTN10748953 (WP3 and WP4). FUNDING: This project was funded by the National Institute for Health and Care Research (NIHR) Programme Grants for Applied Research programme and will be published in full in Programme Grants for Applied Research; Vol. 11, No. 5. See the NIHR Journals Library website for further project information

Serum metabolomic profiling in acute alcoholic hepatitis identifies multiple dysregulated pathways

Background and Objectives While animal studies have implicated derangements of global energy homeostasis in the pathogenesis of acute alcoholic hepatitis (AAH), the relevance of these findings to the development of human AAH remains unclear. Using global, unbiased serum metabolomics analysis, we sought to characterize alterations in metabolic pathways associated with severe AAH and identify potential biomarkers for disease prognosis. Methods This prospective, case-control study design included 25 patients with severe AAH and 25 ambulatory patients with alcoholic cirrhosis. Serum samples were collected within 24 hours of the index clinical encounter. Global, unbiased metabolomics profiling was performed. Patients were followed for 180 days after enrollment to determine survival. Results Levels of 234 biochemicals were altered in subjects with severe AAH. Random-forest analysis, principal component analysis, and integrated hierarchical clustering methods demonstrated that metabolomics profiles separated the two cohorts with 100% accuracy. Severe AAH was associated with enhanced triglyceride lipolysis, impaired mitochondrial fatty acid beta oxidation, and upregulated omega oxidation. Low levels of multiple lysolipids and related metabolites suggested decreased plasma membrane remodeling in severe AAH. While most measured bile acids were increased in severe AAH, low deoxycholate and glycodeoxycholate levels indicated intestinal dysbiosis. Several changes in substrate utilization for energy homeostasis were identified in severe AAH, including increased glucose consumption by the pentose phosphate pathway, altered tricarboxylic acid (TCA) cycle activity, and enhanced peptide catabolism. Finally, altered levels of small molecules related to glutathione metabolism and antioxidant vitamin depletion were observed in patients with severe AAH. Univariable logistic regression revealed 15 metabolites associated with 180-day survival in severe AAH. Conclusion Severe AAH is characterized by a distinct metabolic phenotype spanning multiple pathways. Metabolomics profiling revealed a panel of biomarkers for disease prognosis, and future studies are planned to validate these findings in larger cohorts of patients with severe AAH.This study was funded by Grant 5K08AA017622 from the National Institutes of Health and a University of Pittsburgh Medical Center Pilot Grant to JB. The funders had no role in study design, data collection and analysis, decision to publish, or preparation of the manuscript