Wettability of Nanostructured Surfaces

There are many studies in literature concerning contact angle measurements on different materials/substrates. It is documented that textiles can be coated with multifunctional materials in form of thin films or nanoparticles to acquire characteristics that can improve the protection and comfort of the wearer. The capacity of oxide nanostructures to inhibit fungal development and neutralize bacteria is a direct consequence of their wetting behavior [1–6]. Moreover, the radical modification of wetting behavior of nanostructures from hydrophilic to hydrophobic when changing the pulsed laser deposition (PLD) ambient will be thoroughly discussed

ANALISIS GAYA TAHAN TRANSLATOR MOTOR LINIER PADA SUATU ELEVATOR

Motor linier merupakan salah satujenis mesin elektrik yang bekerja denganmenghasilkan gerak linier. Padaperkembangannya penggunaan motor liniermulai dikenal dan digunakan pada beberapaaplikasi industri dan angkutan masal. Gerakyang dihasilkan motor linier juga digunakanpada aplikasi ropeless elevator. Elevator jenis initidak lagi bergantung pada konversi gerak putarmenjadi gerak linier. Hal ini berakibat padapeningkatan efesiensi dan keandalan elevator.Kebanyakan motor linier digunakan padaaplikasi gerak linier yang horizontal. Oleh sebabitu, penggunaan pada gerak vertikal harusdiperhatikan ketahanannya. Hal itu dikarenakanketika elevator berhenti harus mampu menahanberat penumpang yang sudah naik maupunpenumpang baru. Untuk itulah, penelitian inidilakukan. Pada penelitian ini, akan diambilmotor linier jenis permanent magnet linearsynchronous motor (PMLSM) dengan coil beradapada bagian stator. Linier motor jenis inimemiliki kemampuan untuk menghasilkan gayayang besar serta bagian translator memiliki beratyang ringan.Dari penelitian ini diketahui karakteristik motorlinier, yaitu hubungan arus dari sumber yangditerapkan pada elevator motor linier adalahberbanding lurus terhadap beban yang mampuditahan oleh motor linier dalam keadaan diamatau berhenti.Kata kunci: motor linier, ropeless elevator,PMLS

Realtime Video Classification Using Dense HOF/HOG

ABSTRACT The current state-of-the-art in Video Classification is based on Bag-of-Words using local visual descriptors. Most commonly these are Histogram of Oriented Gradient (HOG) and Histogram of Optical Flow (HOF) descriptors. While such system is very powerful for classification, it is also computationally expensive. This paper addresses the problem of computational efficiency. Specifically: (1) We propose several speed-ups for densely sampled HOG and HOF descriptors and release Matlab code. (2) We investigate the trade-off between accuracy and computational efficiency of descriptors in terms of frame sampling rate and type of Optical Flow method. (3) We investigate the trade-off between accuracy and computational efficiency for the video representation, using either a k-means or hierarchical k-means based visual vocabulary, a Random Forest based vocabulary or the Fisher kernel

TrainMiC, Training in Metrology in Chemistry.

Abstract not availableJRC.D-Institute for Reference Materials and Measurements (Geel

Biomimetic nanocrystalline apatite coatings synthesized by Matrix Assisted Pulsed Laser Evaporation for medical applications

tWe report the deposition by Matrix Assisted Pulsed Laser Evaporation (MAPLE) technique of biomimeticnanocrystalline apatite coatings on titanium substrates, with potential application in tissue engineering.The targets were prepared from metastable, nanometric, poorly crystalline apatite powders, analogousto mineral bone, synthesized through a biomimetic approach by double decomposition process. For thedeposition of thin films, a KrF* excimer laser source was used (λ = 248 nm, τFWHM ≤ 25 ns). The analy-ses revealed the existence, in synthesized powders, of labile non-apatitic mineral ions, associated withthe formation of a hydrated layer at the surface of the nanocrystals. The thin film analyses showedthat the structural and chemical nature of the nanocrystalline apatite was prevalently preserved. Theperpetuation of the non-apatitic environments was also observed. The study indicated that MAPLE isa suitable technique for the congruent transfer of a delicate material, such as the biomimetic hydratednanohydroxyapatite

Pulsed Laser Deposition of Aluminum Nitride Films: Correlation between Mechanical, Optical, and Structural Properties

Aluminum nitride (AlN) films were synthesized onto Si(100) substrates by pulsed laser deposition (PLD) in vacuum or nitrogen, at 0.1, 1, 5, or 10 Pa, and substrate temperatures ranging from RT to 800 °C. The laser parameters were set at: incident laser fluence of 3–10 J/cm2 and laser pulse repetition frequency of 3, 10, or 40 Hz, respectively. The films’ hardness was investigated by depth-sensing nanoindentation. The optical properties were studied by FTIR spectroscopy and UV-near IR ellipsometry. Hardness values within the range of 22–30 GPa and Young’s modulus values of 230–280 GPa have been inferred. These values were determined by the AlN film structure that consisted of nanocrystallite grains, strongly dependent on the deposition parameters. The values of optical constants, superior to amorphous AlN, support the presence of crystallites in the amorphous film matrix. They were visualized by TEM and evidenced by FTIR spectroscopy. The characteristic Reststrahlen band of the h-AlN lattice with component lines arising from IR active phonon vibrational modes in AlN nanocrystallites was well detectable within the spectral range of 950–500 cm−1. Control X-ray diffraction and atomic force microscopy data were introduced and discussed. All measurements delivered congruent results and have clearly shown a correlation between the films’ structure and the mechanical and optical properties dependent on the experimental conditions

A new framework for sign language alphabet hand posture recognition using geometrical features through artificial neural network (part 1)

Hand pose tracking is essential in sign languages. An automatic recognition of performed hand signs facilitates a number of applications, especially for people with speech impairment to communication with normal people. This framework which is called ASLNN proposes a new hand posture recognition technique for the American sign language alphabet based on the neural network which works on the geometrical feature extraction of hands. A user’s hand is captured by a three-dimensional depth-based sensor camera; consequently, the hand is segmented according to the depth analysis features. The proposed system is called depth-based geometrical sign language recognition as named DGSLR. The DGSLR adopted in easier hand segmentation approach, which is further used in segmentation applications. The proposed geometrical feature extraction framework improves the accuracy of recognition due to unchangeable features against hand orientation compared to discrete cosine transform and moment invariant. The findings of the iterations demonstrate the combination of the extracted features resulted to improved accuracy rates. Then, an artificial neural network is used to drive desired outcomes. ASLNN is proficient to hand posture recognition and provides accuracy up to 96.78% which will be discussed on the additional paper of this authors in this journal

Measurement of gauge blocks by interferometry

The key comparison EURAMET.L-K1.2011 on gauge blocks was carried out in the framework of a EURAMET project starting in 2012 and ending in 2015. It involved the participation of 24 National Metrology Institutes from Europe and Egypt, respectively. 38 gauge blocks of steel and ceramic with nominal central lengths between 0.5 mm and 500 mm were circulated. The comparison was conducted in two loops with two sets of artifacts. A statistical technique for linking the reference values was applied. As a consequence the reference value of one loop is influenced by the measurements of the other loop although they did not even see the artifacts of the others. This influence comes solely from three "linking laboratories" which measure both sets of artifacts. In total there were 44 results were not fully consistent with the reference values. This represents 10% of the full set of 420 results which is a considerable high number. At least 12 of them are clearly outliers where the participants have been informed by the pilot as soon as possible. The comparison results help to support the calibration and measurement capabilities (CMCs) of the laboratories involved in the CIPM MRA