69 research outputs found
Recommended from our members
MICE Hall PPS – User's Guide
This document describes the use of the MICE Hall Personnel Protection System ("PPS"). The PPS uses hardware logic and interlocks to track the state of ISIS, the MICE Hall and some experiment subsystems, so as to prevent or limit certain activities during unsuitable situations and therefore ensure the safety of personnel in the Hall
The design and performance of an improved target for MICE
The linear motor driving the target for the Muon Ionisation Cooling Experiment has been redesigned to improve its reliability and performance. A new coil-winding technique is described which produces better magnetic alignment and improves heat transport out of the windings. Improved field-mapping has allowed the more precise construction to be demonstrated, and an enhanced controller exploits the full features of the hardware, enabling increased acceleration and precision. The new user interface is described and analysis of performance data to monitor friction is shown to allow quality control of bearings and a measure of the ageing of targets during use
The design, construction and performance of the MICE scintillating fibre trackers
This is the Pre-print version of the Article. The official published version can be accessed from the link below - Copyright @ 2011 ElsevierCharged-particle tracking in the international Muon Ionisation Cooling Experiment (MICE) will be performed using two solenoidal spectrometers, each instrumented with a tracking detector based on diameter scintillating fibres. The design and construction of the trackers is described along with the quality-assurance procedures, photon-detection system, readout electronics, reconstruction and simulation software and the data-acquisition system. Finally, the performance of the MICE tracker, determined using cosmic rays, is presented.This work was supported by the Science and Technology Facilities Council under grant numbers PP/E003214/1, PP/E000479/1, PP/E000509/1, PP/E000444/1, and through SLAs with STFC-supported laboratories. This work was also supportedby the Fermi National Accelerator Laboratory, which is operated by the Fermi Research Alliance, under contract No. DE-AC02-76CH03000 with the U.S. Department of Energy, and by the U.S. National Science Foundation under grants PHY-0301737,PHY-0521313, PHY-0758173 and PHY-0630052. The authors also acknowledge the support of the World Premier International Research Center Initiative (WPI Initiative), MEXT, Japan
Status Report of the ATLAS SCT Optical Links
The ATLAS SCT optical links system is reviewed. The assembly and testing of prototype opto-hamesses are described. Results are also given from a system test of the SCT barrel modules, including optical readout
Characterisation of the muon beams for the Muon Ionisation Cooling Experiment
A novel single-particle technique to measure emittance has been developed and used to characterise seventeen different muon beams for the Muon Ionisation Cooling Experiment (MICE). The muon beams, whose mean momenta vary from 171 to 281 MeV/c, have emittances of approximately 1.2–2.3 π mm-rad horizontally and 0.6–1.0 π mm-rad vertically, a horizontal dispersion of 90–190 mm and momentum spreads of about 25 MeV/c. There is reasonable agreement between the measured parameters of the beams and the results of simulations. The beams are found to meet the requirements of MICE
The ATLAS SCT Optoelectronics and the Associated Electrical Services
The requirements for the optical links of the ATLAS SCT are described. From the individual detector modules to the first patch panel, the electrical services are integrated with the optical links to aid in mechanical design, construction and integration. The system architecture and critical elements of the system are described. The optical links for the ATLAS SCT have been assembled and mounted onto the carbon fibre support structures. The performance of the system as measured during QA is summarised and compared to the final performance obtained after mounting modules onto the support structures
The optical links of the ATLAS SemiConductor tracker
Optical links are used for the readout of the 4088 silicon microstrip modules that make up the SemiConductor Tracker of the ATLAS experiment at the CERN Large Hadron Collider (LHC). The optical link requirements are reviewed, with particular emphasis on the very demanding environment at the LHC. The on-detector components have to operate in high radiation levels for 10 years, with no maintenance, and there are very strict requirements on power consumption, material and space. A novel concept for the packaging of the on-detector optoelectronics has been developed to meet these requirements. The system architecture, including its redundancy features, is explained and the critical on-detector components are described. The results of the extensive Quality Assurance performed during all steps of the assembly are discussed
Transverse Emittance Reduction in Muon Beams by Ionization Cooling
Accelerated muon beams have been considered for next-generation studies of
high-energy lepton-antilepton collisions and neutrino oscillations. However,
high-brightness muon beams have not yet been produced. The main challenge for
muon acceleration and storage stems from the large phase-space volume occupied
by the beam, derived from the muon production mechanism through the decay of
pions from proton collisions. Ionization cooling is the technique proposed to
decrease the muon beam phase-space volume. Here we demonstrate a clear signal
of ionization cooling through the observation of transverse emittance reduction
in beams that traverse lithium hydride or liquid hydrogen absorbers in the Muon
Ionization Cooling Experiment (MICE). The measurement is well reproduced by the
simulation of the experiment and the theoretical model. The results shown here
represent a substantial advance towards the realization of muon-based
facilities that could operate at the energy and intensity frontiers.Comment: 23 pages and 5 figure
First demonstration of ionization cooling by the Muon Ionization Cooling Experiment
High-brightness muon beams of energy comparable to those produced by
state-of-the-art electron, proton and ion accelerators have yet to be realised.
Such beams have the potential to carry the search for new phenomena in
lepton-antilepton collisions to extremely high energy and also to provide
uniquely well-characterised neutrino beams. A muon beam may be created through
the decay of pions produced in the interaction of a proton beam with a target.
To produce a high-brightness beam from such a source requires that the phase
space volume occupied by the muons be reduced (cooled). Ionization cooling is
the novel technique by which it is proposed to cool the beam. The Muon
Ionization Cooling Experiment collaboration has constructed a section of an
ionization cooling cell and used it to provide the first demonstration of
ionization cooling. We present these ground-breaking measurements.Comment: 19 pages and 6 figure
Electron-muon ranger: performance in the MICE muon beam
The Muon Ionization Cooling Experiment (MICE) will perform a detailed study of ionization cooling to evaluate the feasibility of the technique. To carry out this program, MICE requires an efficient particle-identification (PID) system to identify muons. The Electron-Muon Ranger (EMR) is a fully-active tracking-calorimeter that forms part of the PID system and tags muons that traverse the cooling channel without decaying. The detector is capable of identifying electrons with an efficiency of 98.6%, providing a purity for the MICE beam that exceeds 99.8%. The EMR also proved to be a powerful tool for the reconstruction of muon momenta in the range 100–280 MeV/c
- …