Galaxy And Mass Assembly (GAMA): the signatures of galaxy interactions as viewed from small scale galaxy clustering

Statistical studies of galaxy–galaxy interactions often utilize net change in physical properties of progenitors as a function of the separation between their nuclei to trace both the strength and the observable time-scale of their interaction. In this study, we use two-point auto-, cross-, and mark-correlation functions to investigate the extent to which small-scale clustering properties of star-forming galaxies can be used to gain physical insight into galaxy–galaxy interactions between galaxies of similar optical brightness and stellar mass. The H α star formers, drawn from the highly spatially complete Galaxy And Mass Assembly (GAMA) survey, show an increase in clustering at small separations. Moreover, the clustering strength shows a strong dependence on optical brightness and stellar mass, where (1) the clustering amplitude of optically brighter galaxies at a given separation is larger than that of optically fainter systems, (2) the small-scale-clustering properties (e.g. the strength, the scale at which the signal relative to the fiducial power law plateaus) of star-forming galaxies appear to differ as a function of increasing optical brightness of galaxies. According to cross- and mark-correlation analyses, the former result is largely driven by the increased dust content in optically bright star-forming galaxies. The latter could be interpreted as evidence of a correlation between interaction-scale and optical brightness of galaxies, where physical evidence of interactions between optically bright star formers, likely hosted within relatively massive haloes, persists over larger separations than those between optically faint star formers

Cosmological parameters from SDSS and WMAP

We measure cosmological parameters using the three-dimensional power spectrum P(k) from over 200,000 galaxies in the Sloan Digital Sky Survey (SDSS) in combination with WMAP and other data. Our results are consistent with a ``vanilla'' flat adiabatic Lambda-CDM model without tilt (n=1), running tilt, tensor modes or massive neutrinos. Adding SDSS information more than halves the WMAP-only error bars on some parameters, tightening 1 sigma constraints on the Hubble parameter from h~0.74+0.18-0.07 to h~0.70+0.04-0.03, on the matter density from Omega_m~0.25+/-0.10 to Omega_m~0.30+/-0.04 (1 sigma) and on neutrino masses from <11 eV to <0.6 eV (95%). SDSS helps even more when dropping prior assumptions about curvature, neutrinos, tensor modes and the equation of state. Our results are in substantial agreement with the joint analysis of WMAP and the 2dF Galaxy Redshift Survey, which is an impressive consistency check with independent redshift survey data and analysis techniques. In this paper, we place particular emphasis on clarifying the physical origin of the constraints, i.e., what we do and do not know when using different data sets and prior assumptions. For instance, dropping the assumption that space is perfectly flat, the WMAP-only constraint on the measured age of the Universe tightens from t0~16.3+2.3-1.8 Gyr to t0~14.1+1.0-0.9 Gyr by adding SDSS and SN Ia data. Including tensors, running tilt, neutrino mass and equation of state in the list of free parameters, many constraints are still quite weak, but future cosmological measurements from SDSS and other sources should allow these to be substantially tightened.Comment: Minor revisions to match accepted PRD version. SDSS data and ppt figures available at http://www.hep.upenn.edu/~max/sdsspars.htm

Effect of Austenite Deformation on the Microstructure Evolution and Grain Refinement Under Accelerated Cooling Conditions

Although there has been much research regarding the effect of austenite deformation on accelerated cooled microstructures in microalloyed steels, there is still a lack of accurate data on boundary densities and effective grain sizes. Previous results observed from optical micrographs are not accurate enough, because, for displacive transformation products, a substantial part of the boundaries have disorientation angles below 15 deg. Therefore, in this research, a niobium microalloyed steel was used and electron backscattering diffraction mappings were performed on all of the transformed microstructures to obtain accurate results on boundary densities and grain refinement. It was found that with strain rising from 0 to 0.5, a transition from bainitic ferrite to acicular ferrite occurs and the effective grain size reduces from 5.7 to 3.1 μm. When further increasing strain from 0.5 to 0.7, dynamic recrystallization was triggered and postdynamic softening occurred during the accelerated cooling, leading to an inhomogeneous and coarse transformed microstructure. In the entire strain range, the density changes of boundaries with different disorientation angles are distinct, due to different boundary formation mechanisms. Finally, the controversial influence of austenite deformation on effective grain size of low-temperature transformation products was argued to be related to the differences in transformation conditions and final microstructures

Galaxy And Mass Assembly (GAMA): data release 4 and the z < 0.1 total and z < 0.08 morphological galaxy stellar mass functions

Galaxie

The design of cams for creep testing at constant stress

SIGLELD:6029.3293(NPL-DMA(B)--23). / BLDSC - British Library Document Supply CentreGBUnited Kingdo

Measurement of high temperature mechanical properties of materials

SIGLELD:GPB-82/NPL / BLDSC - British Library Document Supply CentreGBUnited Kingdo

Force calibration of lever creep machines

SIGLEAvailable from British Library Document Supply Centre- DSC:6029.3343(NPL-DMM(A)--40) / BLDSC - British Library Document Supply CentreGBUnited Kingdo