Peri-implant fracture : a rare complication after intramedullary fixation of trochanteric femoral fracture

Introduction Trochanteric femoral fractures are among the most common operatively treated fractures. Intramedullary fixation has become the treatment of choice in many centers around the world. Nevertheless, the knowledge of rare complications of these fractures is limited. In this study, the incidence and treatment strategies for peri-implant fractures (PIF) were assessed. Materials and methods A single-center retrospective cohort study was done on 987 consecutive operatively treated trochanteric fractures. PFNA cephalomedullary nail was used as a fixation method. All patients were followed up from patient records for peri-implant fractures. Plain radiographs as well as different salvage methods were analyzed and compared. Results The total rate of peri-implant fractures was 1.4% (n = 14). The rate of PIF for patients treated with short (200 mm) nails, intermediate-length (240 mm) nails, and long nails was 2.7% (n = 2), 1.5% (n = 11), and 0.7% (n = 1), respectively (ns, p > 0.05 for difference). Treatment of choice for PIF was either ORIF with locking plate (57%, n = 8) or exchange nailing (43%, n = 6). None of the PIF patients needed additional surgeries for non-union, malunion, or delayed union. Conclusions A PIF is a rare complication of intramedullary fixation of trochanteric fractures. It can be treated with either locking plates or exchange nailing with sufficient results. There are no grounds for favoring long nails to avoid PIFs.Peer reviewe

Intramedullary Fixation of Trochanteric Fractures Can Be Safely Performed by Senior Residents Without Immediate Consultant Supervision

OBJECTIVE: To assess the safety of senior residents performing trochanteric hip fracture surgery without immediate consultant supervision DESIGN: A retrospective chart review of trochanteric hip fractures (AO-OTA 31-A) operated in a single center between years 2011 and 2016 (inclusive). Operations were divided into three groups: Group 1 surgeon was a senior resident without any immediate supervision; Group 2 surgeon was a consultant and Group 3surgeon was a senior resident supervised by a consultant. The follow-up period was a minimum of 2 years or until death. All re-operations and surgical related mortality were assessed. SETTING: Helsinki University Hospital, Finland. A tertiary level trauma center. PARTICIPANTS: 987 consecutive trochanteric fractures on 966 patients treated by operative fixation of an intertrochanteric fracture with an intramedullary nail between 2011and 2016 (inclusive). RESULTS: The total number of reoperations was smaller in Group 1 where the surgeon was a senior resident without any immediate supervision compared to Group 2 where the surgeon was a consultant (5.5 % vs 8.8 %, p < 0.05). There were no significant differences in mortality or length of surgery. The total rate of mechanical complications was 2.0 %, with no significant differences between groups. The observed blade cut-out rate was low: 1.3 %, suggesting a good overall quality of surgery. CONCLUSIONS: Senior residents can safely perform intramedullary nailing of trochanteric fractures without immediate supervision. (C) 2021 Association of Program Directors in Surgery. Published by Elsevier Inc. All rights reserved.)Peer reviewe

Infections after intramedullary fixation of trochanteric fractures are uncommon and implant removal is not usually needed

Background and purpose. Infections after intramedullary fixation of trochanteric femoral fractures are rare, but potentially life-threatening complications. There are limited data available to support decision making in these cases. Patients and methods. A retrospective study of 995 consecutive operatively treated trochanteric fractures was made to find out different risk factors for infection and to describe the results of treatment. Results. 28 patients developed a surgical site infection (2.8%) after intramedullary fixation of trochanteric fracture. 15 patients (1.5%) had a deep and 13 patients (1.3%) a superficial surgical site infection. Cigarette smoking ( p < 0.05) and prolonged operative time ( p < 0.05) were significant risk factors for an infection. 15 of 28 patients needed revision surgeries. Implant removal or exchange was needed only for 4 of 28 patients: 1 exchange of the blade, 1 removal of additional cable used to assist reduction and 2 removals of distal locking screws. None of the patients needed additional surgeries for problems with fracture healing. Mortality was not increased among patients with an infection. Interpretation. Infection after intramedullary fixation of trochanteric fractures can be successfully treated without removal or exchange of the fixation material. (c) 2020 Elsevier Ltd. All rights reserved.Peer reviewe

Coil optimisation for transcranial magnetic stimulation in realistic head geometry

Background: Transcranial magnetic stimulation (TMS) allows focal, non-invasive stimulation of the cortex. A TMS pulse is inherently weakly coupled to the cortex; thus, magnetic stimulation requires both high current and high voltage to reach sufficient intensity. These requirements limit, for example, the maximum repetition rate and the maximum number of consecutive pulses with the same coil due to the rise of its temperature. Objective: To develop methods to optimise, design, and manufacture energy-efficient TMS coils in realistic head geometry with an arbitrary overall coil shape. Methods: We derive a semi-analytical integration scheme for computing the magnetic field energy of an arbitrary surface current distribution, compute the electric field induced by this distribution with a boundary element method, and optimise a TMS coil for focal stimulation. Additionally, we introduce a method for manufacturing such a coil by using Litz wire and a coil former machined from polyvinyl chloride. Results: We designed, manufactured, and validated an optimised TMS coil and applied it to brain stimulation. Our simulations indicate that this coil requires less than half the power of a commercial figure-of-eight coil, with a 41% reduction due to the optimised winding geometry and a partial contribution due to our thinner coil former and reduced conductor height. With the optimised coil, the resting motor threshold of abductor pollicis brevis was reached with the capacitor voltage below 600 V and peak current below 3000 A. Conclusion: The described method allows designing practical TMS coils that have considerably higher efficiency than conventional figure-of-eight coils. (C) 2017 Elsevier Inc. All rights reserved.Peer reviewe

Multi-locus transcranial magnetic stimulation system for electronically targeted brain stimulation

Background: Transcranial magnetic stimulation (TMS) allows non-invasive stimulation of the cortex. In multi-locus TMS (mTMS), the stimulating electric field (E-field) is controlled electronically without coil movement by adjusting currents in the coils of a transducer. Objective: To develop an mTMS system that allows adjusting the location and orientation of the E-field maximum within a cortical region. Methods: We designed and manufactured a planar 5-coil mTMS transducer to allow controlling the maximum of the induced E-field within a cortical region approximately 30 mm in diameter. We developed electronics with a design consisting of independently controlled H-bridge circuits to drive up to six TMS coils. To control the hardware, we programmed software that runs on a field-programmable gate array and a computer. To induce the desired E-field in the cortex, we developed an optimization method to calculate the currents needed in the coils. We characterized the mTMS system and conducted a proof-of-concept motor-mapping experiment on a healthy volunteer. In the motor mapping, we kept the transducer placement fixed while electronically shifting the E-field maximum on the precentral gyrus and measuring electromyography from the contralateral hand. Results: The transducer consists of an oval coil, two figure-of-eight coils, and two four-leaf-clover coils stacked on top of each other. The technical characterization indicated that the mTMS system performs as designed. The measured motor evoked potential amplitudes varied consistently as a function of the location of the E-field maximum. Conclusion: The developed mTMS system enables electronically targeted brain stimulation within a cortical region. (c) 2021 The Author(s). Published by Elsevier Inc. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).Peer reviewe

Short-interval intracortical inhibition in human primary motor cortex: A multi-locus transcranial magnetic stimulation study

Short-interval intracortical inhibition (SICI) has been studied with paired-pulse transcranial magnetic stimulation (TMS) by administering two pulses at a millisecond-scale interstimulus interval (ISI) to a single cortical target. It has, however, been difficult to study the interaction of nearby cortical targets with paired-pulse TMS. To overcome this limitation, we have developed a multi-locus TMS (mTMS) device, which allows controlling the stimulus location electronically. Here, we applied mTMS to study SICI in primary motor cortex with paired pulses targeted to adjacent locations, aiming to quantify the extent of the cortical region producing SICI in the location of a test stimulus. We varied the location and timing of the conditioning stimulus with respect to a test stimulus targeted to the cortical hotspot of the abductor pollicis brevis (APB) in order to study their effects on motor evoked potentials. We further applied a two-coil protocol with the conditioning stimulus given by an oval coil only to the surroundings of the APB hotspot, to which a subsequent test stimulus was administered with a figure-of-eight coil. The strongest SICI occurred at ISIs below 1 ms and at ISIs around 2.5 ms. These ISIs increased when the conditioning stimulus receded from the APB hotspot. Our two-coil paired-pulse TMS study suggests that SICI at ISIs of 0.5 and 2.5 ms originate from different mechanisms or neuronal elements.Peer reviewe

Finding needles in haystacks: linking scientific names, reference specimens and molecular data for Fungi

DNA phylogenetic comparisons have shown that morphology-based species recognition often underestimates fungal diversity. Therefore, the need for accurate DNA sequence data, tied to both correct taxonomic names and clearly annotated specimen data, has never been greater. Furthermore, the growing number of molecular ecology and microbiome projects using high-throughput sequencing require fast and effective methods for en masse species assignments. In this article, we focus on selecting and re-annotating a set of marker reference sequences that represent each currently accepted order of Fungi. The particular focus is on sequences from the internal transcribed spacer region in the nuclear ribosomal cistron, derived from type specimens and/or ex-type cultures. Re-annotated and verified sequences were deposited in a curated public database at the National Center for Biotechnology Information (NCBI), namely the RefSeq Targeted Loci (RTL) database, and will be visible during routine sequence similarity searches with NR_prefixed accession numbers. A set of standards and protocols is proposed to improve the data quality of new sequences, and we suggest how type and other reference sequences can be used to improve identification of Fungi

Cardiac anisotropy in boundary-element models for the electrocardiogram

The boundary-element method (BEM) is widely used for electrocardiogram (ECG) simulation. Its major disadvantage is its perceived inability to deal with the anisotropic electric conductivity of the myocardial interstitium, which led researchers to represent only intracellular anisotropy or neglect anisotropy altogether. We computed ECGs with a BEM model based on dipole sources that accounted for a “compound” anisotropy ratio. The ECGs were compared with those computed by a finite-difference model, in which intracellular and interstitial anisotropy could be represented without compromise. For a given set of conductivities, we always found a compound anisotropy value that led to acceptable differences between BEM and finite-difference results. In contrast, a fully isotropic model produced unacceptably large differences. A model that accounted only for intracellular anisotropy showed intermediate performance. We conclude that using a compound anisotropy ratio allows BEM-based ECG models to more accurately represent both anisotropies

Technology transfer model for Austrian higher education institutions

The aim of this paper is to present the findings of a PhD research (Heinzl 2007, Unpublished PhD Thesis) conducted on the Universities of Applied Sciences in Austria. Four of the models that emerge from this research are: Generic Technology Transfer Model (Sect. 5.1); Idiosyncrasies Model for the Austrian Universities of Applied Sciences (Sect. 5.2); Idiosyncrasies-Technology Transfer Effects Model (Sect. 5.3); Idiosyncrasies-Technology Transfer Cumulated Effects Model (Sect. 5.3). The primary and secondary research methods employed for this study are: literature survey, focus groups, participant observation, and interviews. The findings of the research contribute to a conceptual design of a technology transfer system which aims to enhance the higher education institutions' technology transfer performance. © 2012 Springer Science+Business Media, LLC