Analysis by Finite Element Calculations of Light Scattering in Laser-textured AZO Films for PV thin-film Solar Cells

In the thin-film photovoltaic industry, to achieve a high light scattering in one or more of the cell interfaces is one of the strategies that allow an enhancement of light absorption inside the cell and, therefore, a better device behavior and efficiency. Although chemical etching is the standard method to texture surfaces for that scattering improvement, laser light has shown as a new way for texturizing different materials, maintaining a good control of the final topography with a unique, clean, and quite precise process. In this work AZO films with different texture parameters are fabricated. The typical parameters used to characterize them, as the root mean square roughness or the haze factor, are discussed and, for deeper understanding of the scattering mechanisms, the light behavior in the films is simulated using a finite element method code. This method gives information about the light intensity in each point of the system, allowing the precise characterization of the scattering behavior near the film surface, and it can be used as well to calculate a simulated haze factor that can be compared with experimental measurements. A discussion of the validation of the numerical code, based in a comprehensive comparison with experimental data is include

Activation of visible up-conversion luminescence in transparent and conducting ZnO:Er:Yb films by laser annealing

Transparent and conducting ZnO:Er:Yb thin films with visible up-conversion (660-nm emission under 980-nm excitation) were fabricated by RF magnetron sputtering. The as-deposited films were found to be transparent and conducting and the activation of the Er ions in these films to produce up-conversion luminescence was achieved by different post deposition annealing treatments in air, vacuum or by laser annealing using a Nd:YVO4 laser. The structural, electrical and optical properties and the up-conversion efficiency of these films were found to be strongly influenced by the annealing method, and a detailed study is reported in this paper. It has been demonstrated that, although the air annealing was the most efficient in terms of up-conversion, laser annealing was the only method capable of activating Er ions while preserving the electrical conductivity of the doped films. It has been shown that a minimum energy was needed in laser annealing to optically activate the rare earth ions in the ZnO host material to produce up-conversion. Up-converting and transparent conducting ZnO:Er:Yb films with an electrical resistivity of 5×10-2 Ω·cm and transparency ~80% in the visible wavelength range has been achieved by laser annealing

Investigation on the structural changes of ZnO:Er:Yb thin film during laser annealing to fabricate a transparent conducting upconverter

A transparent and conducting ZnO:Er:Yb thin film with upconversion properties has been achieved after being annealed with continuous laser radiation just before the ablation point of the material. This work demonstrates that the laser energy preserves the conductivity of the film and at the same time creates an adequate surrounding for Er and Yb to produce visible upconversion at 660, 560, 520, and 480 nm under 980 nm laser excitation. The relation between the structural, electrical and upconversion properties is discussed. It is observed that the laser energy melts part of the material, which recrystallizes creating rare earth oxides and two different wurtzite structures, one with substitutional rare earths and oxygen vacancies (responsible for the conductivity) and the other without substitutional rare earth ions (responsible for the upconversion emission)

Spectral characterization of laser-accelerated protons with CR-39 nuclear track detector

CR-39 nuclear track material is frequently used for the detection of protons accelerated in laser-plasma interactions. The measurement of track densities allows for determination of particle angular distributions, and information on the kinetic energy can be obtained by the use of passive absorbers. We present a precise method of measuring spectral distributions of laser-accelerated protons in a single etching and analysis process. We make use of a one-to-one relation between proton energy and track size and present a precise calibration based on monoenergetic particle beams. While this relation is limited to proton energies below 1 MeV, we show that the range of spectral measurements can be significantly extended by simultaneous use of absorbers of suitable thicknesses. Examples from laser-plasma interactions are presented, and quantitative results on proton energies and particle numbers are compared to those obtained from a time-of-flight detector. The spectrum end points of continuous energy distributions have been determined with both detector types and coincide within 50-100 keV

Analysis by Finite Element Calculations of Light Scattering in Laser-textured AZO Films for PV thin-film Solar Cells

In the thin-film photovoltaic industry, to achieve a high light scattering in one or more of the cell interfaces is one of the strategies that allow an enhancement of light absorption inside the cell and, therefore, a better device behavior and efficiency. Although chemical etching is the standard method to texture surfaces for that scattering improvement, laser light has shown as a new way for texturizing different materials, maintaining a good control of the final topography with a unique, clean, and quite precise process. In this work AZO films with different texture parameters are fabricated. The typical parameters used to characterize them, as the root mean square roughness or the haze factor, are discussed and, for deeper understanding of the scattering mechanisms, the light behavior in the films is simulated using a finite element method code. This method gives information about the light intensity in each point of the system, allowing the precise characterization of the scattering behavior near the film surface, and it can be used as well to calculate a simulated haze factor that can be compared with experimental measurements. A discussion of the validation of the numerical code, based in a comprehensive comparison with experimental data is include

Activation of visible up-conversion luminescence in transparent and conducting ZnO:Er:Yb films by laser annealing

Transparent and conducting ZnO:Er:Yb thin films with visible up-conversion (660-nm emission under 980-nm excitation) were fabricated by RF magnetron sputtering. The as-deposited films were found to be transparent and conducting and the activation of the Er ions in these films to produce up-conversion luminescence was achieved by different post deposition annealing treatments in air, vacuum or by laser annealing using a Nd:YVO4 laser. The structural, electrical and optical properties and the up-conversion efficiency of these films were found to be strongly influenced by the annealing method, and a detailed study is reported in this paper. It has been demonstrated that, although the air annealing was the most efficient in terms of up-conversion, laser annealing was the only method capable of activating Er ions while preserving the electrical conductivity of the doped films. It has been shown that a minimum energy was needed in laser annealing to optically activate the rare earth ions in the ZnO host material to produce up-conversion. Up-converting and transparent conducting ZnO:Er:Yb films with an electrical resistivity of 5×10-2 Ω·cm and transparency ~80% in the visible wavelength range has been achieved by laser annealing

Investigation on the structural changes of ZnO:Er:Yb thin film during laser annealing to fabricate a transparent conducting upconverter

A transparent and conducting ZnO:Er:Yb thin film with upconversion properties has been achieved after being annealed with continuous laser radiation just before the ablation point of the material. This work demonstrates that the laser energy preserves the conductivity of the film and at the same time creates an adequate surrounding for Er and Yb to produce visible upconversion at 660, 560, 520, and 480 nm under 980 nm laser excitation. The relation between the structural, electrical and upconversion properties is discussed. It is observed that the laser energy melts part of the material, which recrystallizes creating rare earth oxides and two different wurtzite structures, one with substitutional rare earths and oxygen vacancies (responsible for the conductivity) and the other without substitutional rare earth ions (responsible for the upconversion emission)

Optimization of Laser Processes for Local Rear Contacting of Passivated Silicon Solar Cells

AbstractLaser Firing Contact (LFC) and Laser Doping (LD) have become potential alternatives to the Al BSF thermal processing conventionally used in p-type c-Si solar cell rear contacts. Optimized LFC and LD processes allow, not only the generation of efficient micro-contacts, but also the diffusion of p-type doping impurities reducing the surface recombination velocity due to the formation of a local back surface field (BSF). In this work, three different laser strategies to create ohmic micro-contacts are studied: 1) evaporated Aluminum LFC, 2) Aluminum foil LFC and 3) Aluminum oxide (Al2O3) LD. The laser source used was a pulsed Nd-YAG 1064nm laser working in the nanosecond regime. Laser parameters were explored to optimize the electrical behavior of the contacts and their carrier recombination rate. Optimized laser parameters lead to specific contact resistance in the 1.0 - 1.3 mΩ·cm2 range for all three strategies. From the point of view of carrier recombination, better results were obtained for Al2O3 LD, probably related to the lower energy pulse needed to create the contact. Next, the three proposed laser approaches were applied to the back surface of heterojunction silicon solar cells. Contact quality was not limiting any cell performance indicating that the contact quality is good enough to be applied in high-efficiency c-Si cell concepts. On the other hand, surface recombination velocity at the rear surface on the final devices also points out to Al2O3 LD as the best alternative