39,553 research outputs found
Investigation of aeroelastic stability phenomena of a helicopter by in-flight shake test
The analytical capability of the helicopter stability program is discussed. The parameters which are found to be critical to the air resonance characteristics of the soft in-plane hingeless rotor systems are detailed. A summary of two model test programs, a 1/13.8 Froude-scaled BO-105 model and a 1.67 meter (5.5 foot) diameter Froude-scaled YUH-61A model, are presented with emphasis on the selection of the final parameters which were incorporated in the full scale YUH-61A helicopter. Model test data for this configuration are shown. The actual test results of the YUH-61A air resonance in-flight shake test stability are presented. Included are a concise description of the test setup, which employs the Grumman Automated Telemetry System (ATS), the test technique for recording in-flight stability, and the test procedure used to demonstrate favorable stability characteristics with no in-plane damping augmentation (lag damper removed). The data illustrating the stability trend of air resonance with forward speed and the stability trend of ground resonance for percent airborne are presented
Dynamical pattern formation during growth of a dual-species Bose-Einstein condensate
We simulate the growth of a dual species Bose-Einstein condensate using a
Gross-Pitaevskii equation with an additional gain term giving rise to the
growth. Such growth occurs during simultaneous evaporative cooling of a mixture
of two gases. The ground state of a dual condensate is normally either a
miscible mixture, or an immiscible phase with two spatially separated
components. In a cigar trap the ground state typically consists of one
component in the center, and the other component flanking it. Our simulations
show that when the condensates are formed in a cigar trap and the mixture is
phase separated, then the final state upon the end of the growth is generally
far from the true ground state of the system. Instead it consists of multiple,
interleaved bubbles of the two species. Such a pattern was observed recently in
an experiment by Wieman's group at JILA, and our simulations are in good
qualitative agreement with the experiment. We explain the pattern formation as
due to the onset of modulation instability during growth, and study the
dependence of the final state pattern on various parameters of the system
Modeling of premixing-prevaporizing fuel-air mixing passages
The development of a computer program for the analytical prediction of the distribution of liquid and vapor fuel in the premixing-prevaporizing passage by the direct injection method is described. The technical approach adopted for this program is to separate the problem into three parts each with its own computer code. These three parts are: calculation of the two-dimensional or axisymmetric air flow; calculation of the three-dimensional fuel droplet evaporation; and calculation of the fuel vapor diffusion. This method of approach is justified because premixing passages operate at lean equivalence ratios. Hence, a weak interaction assumption can be made wherein the airflow can affect the fuel droplet behavior but the fuel droplet behavior does not affect the airflow
The regulation of matrix metalloproteinases and their inhibitors
The matrix metalloproteinases (MMP) are a family of 23 enzymes in man. These enzymes were originally described as cleaving extracellular matrix (ECM) substrates with a predominant role in ECM homeostasis, but it is now clear that they have much wider functionality. Control over MMP and/or tissue inhibitor of metalloproteinases (TIMP) activity in vivo occurs at different levels and involves factors such as regulation of gene expression, activation of zymogens and inhibition of active enzymes by specific inhibitors. Whilst these enzymes and inhibitors have clear roles in physiological tissue turnover and homeostasis, if control of their expression or activity is lost, they contribute to a number of pathologies including e.g. cancer, arthritis and cardiovascular disease. The expression of many MMPs and TIMPs is regulated at the level of transcription by a variety of growth factors, cytokines and chemokines, though post-transcriptional pathways may contribute to this regulation in specific cases. The contribution of epigenetic modifications has also been uncovered in recent years. The promoter regions of many of these genes have been, at least partly, characterised including the role of identified single nucleotide polymorphisms. This article aims to review current knowledge across these gene families and use a bioinformatic approach to fill the gaps where no functional data are available
Zenithal bistability in a nematic liquid crystal device with a monostable surface condition
The ground-state director configurations in a grating-aligned, zenithally bistable nematic device are calculated in two dimensions using a Q tensor approach. The director profiles generated are well described by a one-dimensional variation of the director across the width of the device, with the distorted region near the grating replaced by an effective surface anchoring energy. This work shows that device bistability can in fact be achieved by using a monostable surface term in the one-dimensional model. This implies that is should be possible to construct a device showing zenithal bistability without the need for a micropatterned surface
Analytical modeling of operating characteristics of premixing-prevaporizing fuel-air mixing passages. Volume 2: User's manual
A user's manual describing the operation of three computer codes (ADD code, PTRAK code, and VAPDIF code) is presented. The general features of the computer codes, the input/output formats, run streams, and sample input cases are described
User's manual for Axisymmetric Diffuser Duct (ADD) code. Volume 1: General ADD code description
This User's Manual contains a complete description of the computer codes known as the AXISYMMETRIC DIFFUSER DUCT code or ADD code. It includes a list of references which describe the formulation of the ADD code and comparisons of calculation with experimental flows. The input/output and general use of the code is described in the first volume. The second volume contains a detailed description of the code including the global structure of the code, list of FORTRAN variables, and descriptions of the subroutines. The third volume contains a detailed description of the CODUCT code which generates coordinate systems for arbitrary axisymmetric ducts
The quantum-mechanical basis of an extended Landau-Lifshitz-Gilbert equation for a current-carrying ferromagnetic wire
An extended Landau-Lifshitz-Gilbert (LLG) equation is introduced to describe
the dynamics of inhomogeneous magnetization in a current-carrying wire. The
coefficients of all the terms in this equation are calculated
quantum-mechanically for a simple model which includes impurity scattering.
This is done by comparing the energies and lifetimes of a spin wave calculated
from the LLG equation and from the explicit model. Two terms are of particular
importance since they describe non-adiabatic spin-transfer torque and damping
processes which do not rely on spin-orbit coupling. It is shown that these
terms may have a significant influence on the velocity of a current-driven
domain wall and they become dominant in the case of a narrow wall.Comment: 19 pages, 1 figur
Recommended from our members
The effect of weld residual stresses and their re-distribution with crack growth during fatigue under constant amplitude loading
In this work the evolution of the residual stresses in a MIG-welded 2024-T3 aluminium alloy M(T) specimen during in situ fatigue crack growth at constant load amplitude has been measured with neutron diffraction. The plastic relaxation and plasticity-induced residual stresses associated with the fatigue loading were found to be small compared with the stresses arising due to elastic re-distribution of the initial residual stress field. The elastic re-distribution was modelled with a finite element simulation and a good correlation between the experimentally-determined and the modelled stresses was found. A significant mean stress effect on the fatigue crack growth rate was seen and this was also accurately predicted using the measured initial residual stresses
- …