Anomalous accelerations of the Pageos spacecraft

Anomalous accelerations of Pageos satellite and application of theory to predict perturbations in mean motio

Optical properties of cometary particles collected by the COSIMA mass spectrometer on-board <i>Rosetta</i> during the rendezvous phase around comet 67P/Churyumov–Gerasimenko

40 000 collected cometary particles have been identified on the 21 targets exposed by the COSIMA experiment on-board Rosetta to the environment of comet 67P/Churyumov–Gerasimenko from 2014 August to 2016 September. The images of the targets where obtained by the COSIMA microscope (Cosiscope, 13.95 μm pixel−1) with near grazing incidence, which is optimal for the primary objective (detection of collected particles) but very challenging for photometry. However, more than 300 of the collected particles are larger than 100 μm which makes it possible to derive constraints on the optical properties from the distribution of light levels within the particles. Two types of particles collected by COSIMA (compact particles and cluster particles) have been identified in Langevin et al. The best estimate reflectance factors of compact particles range from 10 per cent to 23 per cent. For cluster particles (>90 per cent of large collected particles), the comparison of the signal profiles with illumination from two opposite directions shows that there is scattering within the particles, with a mean free path in the 20–25 μm range, which requires high porosity. The best estimate reflectance factors of cluster particles range from 3 per cent to 22 per cent. This range of reflectance factors overlaps with that obtained from observations of the cometary nucleus at macroscopic scales by OSIRIS and it is consistent with that measured for interplanetary dust particles collected in the stratosphere of the Earth

Low Frequency Tilt Seismology with a Precision Ground Rotation Sensor

We describe measurements of the rotational component of teleseismic surface waves using an inertial high-precision ground-rotation-sensor installed at the LIGO Hanford Observatory (LHO). The sensor has a noise floor of 0.4 nrad$/ \sqrt{\rm Hz}$ at 50 mHz and a translational coupling of less than 1 $\mu$rad/m enabling translation-free measurement of small rotations. We present observations of the rotational motion from Rayleigh waves of six teleseismic events from varied locations and with magnitudes ranging from M6.7 to M7.9. These events were used to estimate phase dispersion curves which shows agreement with a similar analysis done with an array of three STS-2 seismometers also located at LHO

Blip glitches in Advanced LIGO data

Blip glitches are short noise transients present in data from ground-based gravitational-wave observatories. These glitches resemble the gravitational-wave signature of massive binary black hole mergers. Hence, the sensitivity of transient gravitational-wave searches to such high-mass systems and other potential short duration sources is degraded by the presence of blip glitches. The origin and rate of occurrence of this type of glitch have been largely unknown. In this paper we explore the population of blip glitches in Advanced LIGO during its first and second observing runs. On average, we find that Advanced LIGO data contains approximately two blip glitches per hour of data. We identify four subsets of blip glitches correlated with detector auxiliary or environmental sensor channels, however the physical causes of the majority of blips remain unclear

Tethered subsatellite study

The results are presented of studies performed relating to the feasibility of deploying a subsatellite from the shuttle by means of a tether. The dynamics, the control laws, the aerodynamics, the heating, and some communication considerations of the tethered subsatellite system are considered. Nothing was found that prohibits the use of a subsatellite joined to the shuttle by a long (100 km) tether. More detailed studies directed at specific applications are recommended

Improving LIGO calibration accuracy by tracking and compensating for slow temporal variations

Calibration of the second-generation LIGO interferometric gravitational-wave detectors employs a method that uses injected periodic modulations to track and compensate for slow temporal variations in the differential length response of the instruments. These detectors utilize feedback control loops to maintain resonance conditions by suppressing differential arm length variations. We describe how the sensing and actuation functions of these servo loops are parameterized and how the slow variations in these parameters are quantified using the injected modulations. We report the results of applying this method to the LIGO detectors and show that it significantly reduces systematic errors in their calibrated outputs.Comment: 13 pages, 8 figures. This is an author-created, un-copyedited version of an article published in Classical and Quantum Gravity. IOP Publishing Ltd is not responsible for any errors or omissions in this version of the manuscript or any version derived from i

Performance of the Charge Injection Capability of Suzaku XIS

A charge injection technique is applied to the X-ray CCD camera, XIS (X-ray Imaging Spectrometer) onboard Suzaku. The charge transfer inefficiency (CTI) in each CCD column (vertical transfer channel) is measured by the injection of charge packets into a transfer channel and subsequent readout. This paper reports the performances of the charge injection capability based on the ground experiments using a radiation damaged device, and in-orbit measurements of the XIS. The ground experiments show that charges are stably injected with the dispersion of 91eV in FWHM in a specific column for the charges equivalent to the X-ray energy of 5.1keV. This dispersion width is significantly smaller than that of the X-ray events of 113eV (FWHM) at approximately the same energy. The amount of charge loss during transfer in a specific column, which is measured with the charge injection capability, is consistent with that measured with the calibration source. These results indicate that the charge injection technique can accurately measure column-dependent charge losses rather than the calibration sources. The column-to-column CTI correction to the calibration source spectra significantly reduces the line widths compared to those with a column-averaged CTI correction (from 193eV to 173eV in FWHM on an average at the time of one year after the launch). In addition, this method significantly reduces the low energy tail in the line profile of the calibration source spectrum.Comment: Paper contains 18 figures and 15 tables. Accepted for publication in PAS

The production of platinum-coated silicate nanoparticle aggregates for use in hypervelocity impact experiments

We present a method for producing metal-coated low-density (?3) aggregate silicate dust particles for use in hypervelocity impact (HVI) experiments. Particles fabricated using the method are shown to have charged and electrostatically accelerated in the Max Planck Institut für Kernphysik (MPI-K) 2 MV Van de Graaff accelerator, allowing the production of impact ionization mass spectra of silicate particles (impacting at velocities ranging from ?1 to >30 km s?1, corresponding to sizes of >1 ?m to <0.1 ?m) using the Large Area Mass Analyser (LAMA) instrument, designed for cosmic dust detection in space. Potential uses for the coated grains, such as in the calibration of aerogel targets similar to those used on the Stardust spacecraft, are also discussed